Nissan Qashqai J11. Manual - part 2216

 

  Index      Nissan     Nissan Qashqai J11 - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  2214  2215  2216  2217   ..

 

 

Nissan Qashqai J11. Manual - part 2216

 

 

DAS-278

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BC3-00 REAR LEFT WHEEL SENSOR

C1BC3-00 REAR LEFT WHEEL SENSOR

DTC Description

INFOID:0000000010417033

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Rear left wheel sensor
• Rear left sensor rotor
• ABS actuator and electric unit (control unit)
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Start the engine.

2.

Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1 minute.

3.

Stop the vehicle.

4.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

5.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BC3-00” detected?

YES

>> Proceed to 

DAS-278, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417034

1.

CHECK REAR LH WHEEL SENSOR SYSTEM

With CONSULT

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES

>> Check the DTC. Refer to 

BRC-53, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BC3-00

RL WHEEL SENSOR
(Rear left wheel sensor)

When a malfunction is detected in rear left wheel sensor system.

DAS

C1BC3-00 REAR LEFT WHEEL SENSOR

DAS-279

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

Is DTC “C1BC3-00”, “U1000-00” or other DTC detected?

YES (“C1BC3-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END

DAS-280

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BC4-00 DECEL G SENSOR

C1BC4-00 DECEL G SENSOR

DTC Description

INFOID:0000000010417035

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Yaw rate/side/decel G sensor [integrated in ABS actuator and electric unit (control unit)]
• ABS actuator and electric unit (control unit)
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Ride Control (brake) function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BC4-00” detected?

YES

>> Proceed to 

DAS-280, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417036

1.

CHECK DECEL G SENSOR SYSTEM

With CONSULT

Perform self-diagnosis for “ABS”.
Is DTC detected?

YES

>> Check the DTC. Refer to 

BRC-53, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

Is DTC “C1BC4-00”, “U1000-00” or other DTC detected?

YES (“C1BC4-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

YES (other DTC)>>Check the DTC.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BC4-00

DECEL G SENSOR
(Decel G sensor)

When a malfunction is detected in decel G sensor system.

DAS

C1BC4-00 DECEL G SENSOR

DAS-281

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

NO

>> INSPECTION END

 

 

 

 

 

 

 

Content   ..  2214  2215  2216  2217   ..