Nissan Qashqai J11. Manual - part 2207

DAS-242

< BASIC INSPECTION >

[CHASSIS CONTROL]

CONFIGURATION (CHASSIS CONTROL MODULE)

Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

>> GO TO 8.

8.

WRITING (MANUAL WRITING)

CONSULT Configuration

1.

Select “Manual Configuration”.

2.

Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the
chassis control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 9.

9.

VERIFYING TYPE ID (2)

Compare “Type ID” written into the chassis control module with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 10.

10.

CHECKING CHASSIS CONTROL WARNING

1.

Turn the ignition switch OFF.

2.

Turn the ignition switch ON and check that the chassis control warning to information display of combina-
tion meter displays OFF after staying illuminated for approximately two seconds.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Perform the “Self Diagnostic Result” of “CHASSIS CONTROL”. Refer to 

DAS-219, "CONSULT

Function"

.

11.

PERFORMING SUPPLEMENTARY WORK

1.

Perform the self-diagnosis of all systems.

2.

Erase self-diagnosis results.

>> End of work.

DAS

C1B92-00 BRAKE CONTROL SYSTEM

DAS-243

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

DTC/CIRCUIT DIAGNOSIS

C1B92-00 BRAKE CONTROL SYSTEM

DTC Description

INFOID:0000000010416985

DTC DETECTION LOGIC

POSSIBLE CAUSE

• ABS actuator and electric unit (control unit) system
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Ride Control function
• Active Trace Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1B92-00” detected?

YES

>> Proceed to 

DAS-243, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010416986

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

With CONSULT

Perform self-diagnosis for “ABS”.
Is DTC detected?

YES

>> Check the DTC. Refer to 

BRC-53, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

Is DTC “C1B92”, “U1000” or other DTC detected?

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1B92-00

BRAKE CONTROL SYSTEM
(Brake control system)

When a malfunction is detected in ABS actuator and electric unit (control unit) sys-
tem.

DAS-244

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1B92-00 BRAKE CONTROL SYSTEM

YES (“C1B92-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END

DAS

C1B93-00 ENGINE/HEV SYSTEM

DAS-245

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1B93-00 ENGINE/HEV SYSTEM

DTC Description

INFOID:0000000010416987

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Engine system
• ECM
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1B93-00” detected?

YES

>> Proceed to 

DAS-245, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010416988

1.

CHECK ECM SYSTEM

With CONSULT

Perform self-diagnosis for “ENGINE”.

Is DTC detected?

YES

>> Check the DTC. Refer to 

ECH-71, "DTC Index"

 (HRA2DDT), 

ECM-93, "DTC Index"

 (MR20DD),

ECK-97, "DTC Index"

 (K9K) or 

EC9-108, "DTC Index"

 (R9M)

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

Is DTC “C1B93-00”, “U1000-00” or other DTC detected?

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1B93-00

ENGINE/HEV SYSTEM
(Engine/HEV system)

When a malfunction is detected in ECM system.