Nissan Qashqai J11. Manual - part 219

ECH-174

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P012A TC BOOST SENSOR

YES

>> Replace turbocharger boost sensor.

NO

>> Repair or replace error-detected parts.

P0130 HO2S1

ECH-175

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

P0130 HO2S1

DTC Logic

INFOID:0000000010379067

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

Turn ignition switch OFF and wait at least 12 minutes.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Start engine and warm it up to normal operating temperature.

2.

Maintain the following conditions for at least 11 consecutive minutes.

CAUTION:

Always drive vehicle at safe speed.

3.

Check DTC.

Is DTC is detected?

YES

>> Go to 

ECH-175, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010379068

1.

CHECK ECM HARNESS CONNECTOR CONNECTIONS

Check ECM connector connection F18.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace ECM connector connection.

2.

CHECK HEATED OXYGEN SENSOR 1 HARNESS CONNECTOR CONNECTION

Check heated oxygen sensor 1 harness connector connection F48.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace heated oxygen sensor 1 harness connector.

3.

CHECK GROUND CONNECTION

Check ground connection E4. Refer to Ground Inspection in 

GI-43, "Circuit Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible Cause

P0130

O2 SENSOR 1 B1
(O2 sensor circuit bank 1 
sensor 1)

• Heated oxygen sensor 1 voltage to ECM is 

0.02 V or less for 10 seconds or more.

• Heated oxygen sensor 1 voltage to ECM is 

1.395 V or more 0.01 seconds or more.

• ECM detects heated oxygen sensor 1 voltage 

between 0.25 V to 0.445 V during 0.2 sec-
onds.

• When minimum period duration of heated ox-

ygen sensor 1 is abnormal duration.

• Harness or connectors

(The sensor circuit is open or short-
ed.)

• Heated oxygen sensor 1

Selector lever

Suitable position

Vehicle speed

1 km/h (0.6 MPH) or more

Engine speed

1,215 - 3,750 rpm

ECH-176

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P0130 HO2S1

NO

>> Repair or replace ground connection.

4.

CHECK HO2S1 GROUND CIRCUIT FOR OPEN AND SHORT

1.

Disconnect heated oxygen sensor 1 harness connector.

2.

Disconnect ECM harness connector.

3.

Check harness continuity between HO2S1 harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.

CHECK HO2S1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Check harness continuity between HO2S1 harness connector and ECM harness connector.

2.

Check harness continuity between HO2S1 harness connector or ECM harness connector and ground.

3.

Also check harness for short to power.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace heated oxygen sensor 1.

NO

>> Repair or replace error-detected parts.

HO2S1

ECM

Continuity

Connector

Terminal

Connector

Terminal

F48

1

F18

122

existed

HO2S1

ECM

Continuity

Connector

Terminal

Connector

Terminal

F48

2

F18

99

existed

HO2S1

ECM

Ground

Continuity

Connector

Terminal

Connector

Terminal

F48

2

F18

99

Ground

Not existed

P0135 HO2S1 HEATER

ECH-177

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

P0135 HO2S1 HEATER

DTC Logic

INFOID:0000000010379070

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

Turn ignition switch OFF and wait at least 12 minutes.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 3 seconds.

2.

Check DTC.

Is DTC detected?

YES

>> Go to 

ECH-177, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010379071

1.

CHECK ECM HARNESS CONNECTOR CONNECTIONS

Check ECM connector connection F17.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace ECM connector connection.

2.

CHECK HEATED OXYGEN SENSOR 1 HARNESS CONNECTOR CONNECTION

Check heated oxygen sensor 1 harness connector connection F48.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace heated oxygen sensor 1 harness connector.

3.

CHECK GROUND CONNECTION

Check ground connection E4. Refer to Ground Inspection in 

GI-43, "Circuit Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace ground connection.

4.

CHECK HO2S1 POWER SUPPLY CIRCUIT

1.

Disconnect heated oxygen sensor 1 harness connector.

2.

Turn ignition switch ON.

3.

Check the voltage between HO2S1 sensor 1 harness connector and ground.

 DTC No.

CONSULT screen terms

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P0135

O2 SENSOR 1 HEATER 
B1
(O2 sensor heater circuit 
bank 1 sensor 1)

• ECM detects open circuit of Heated oxygen sen-

sor 1 heater circuit for 2.5 second or more.

• ECM detects short circuit to power of Heated ox-

ygen sensor 1 heater circuit for 2.5 second or 
more.

• ECM detects short circuit to ground of Heated ox-

ygen sensor 1 heater circuit for 2.5 second or 
more.

• Harness or connectors

(The heated oxygen sensor 1 heater 
circuit is open or shorted.)

• Heated oxygen sensor 1 heater