Nissan Qashqai J11. Manual - part 2021

MWI-20

< SYSTEM DESCRIPTION >

SYSTEM (METER SYSTEM)

NOTE:
• Average fuel consumption on the information display is updated approximately every 30 seconds.
• Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “

−−−

”

is displayed until after a travel of 30 seconds and approximately 500 m (0.31 mile).

• The numerical figure following after “

φ

” indicated on the vehicle information display shows average fuel con-

sumption.

Range (Distance to Empty)

The combination meter calculates range based on the following signals, and the calculated value is displayed
on the information display.

NOTE:
• Distance to empty on the information display is updated approximately every 30 seconds.
• When the ignition switch is turned from OFF to ON, “

−−−

” is displayed until after a travel of approximately

500 m (0.31 mile).

• The indicated values may not match each other when refueling with the ignition switch ON.

Average Vehicle Speed

The combination meter calculates average vehicle speed based on the following signals, and the calculated
value is displayed on the information display.

NOTE:
• Average vehicle speed on the information display is updated approximately every 30 seconds.
• Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “

−−−

”

is displayed until after a 30 seconds.

Elapsed Time

The combination meter measures and displays elapsed time (ignition switch ON time).

Driving Distance

The combination meter calculates mileage, based on the following signals and displays the mileage on the
information display.

Signal name

Signal path

Ignition signal

—

Fuel consumption monitor signal

ECM  

Combination 

meter

Vehicle speed signal

ABS actuator and electric unit (control unit) 

 Combination meter

Signal name

Signal path

Ignition signal

—

Fuel level sensor signal

Fuel level sensor unit 

 Combination meter

Fuel consumption monitor signal

ECM  

Combination 

meter

Vehicle speed signal

ABS actuator and electric unit (control unit) 

 Combination meter

Signal name

Signal path

Ignition signal

—

Vehicle speed signal

ABS actuator and electric unit (control unit) 

 Combination meter

Signal name

Signal path

Ignition signal

—

Vehicle speed signal

ABS actuator and electric unit (control unit) 

 Combination meter

MWI

SYSTEM (METER SYSTEM)

MWI-21

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Outside Temperature

• The combination meter corrects an indicated temperature, based on various signals.
• The combination meter calculates outside temperature based on the following signals, and the calculated

value is displayed on the information display.

Correction Process (Temperature indicated soon after the ignition switch ON)

• A temperature indicated soon after the ignition switch is turned ON depends on the time from the ignition

switch OFF to ON and a temperature detected by the ambient sensor.

When any condition described below is met, an ambient sensor-detected temperature is indicated.

- Time from the ignition switch OFF to ON 

≥

 Predetermined time

- Sensor-detected temperature < Temperature at the last ignition switch OFF

Correction Process (Temperature at the Ignition switch ON)

• A temperature indicated when the ignition switch is ON depends on a vehicle speed, an ambient sensor-

detected temperature, and traveling time.

The temperature on the information display is corrected to an ambient sensor-detected temperature when the following condition
is met.

- Ambient sensor-detected temperature < Temperature on the information display

A temperature on the information display is not updated when the following condition is met.

- Ambient sensor-detected temperature 

≥

 Temperature on the information display

- Vehicle speed 

≤

 20 km/h (12 MPH)

A temperature on the information display slowly rises to an ambient sensor-detected temperature when the following condition is
met.

- Ambient sensor-detected temperature 

≥

 Temperature on the information display

- Vehicle speed 

≥

 20 km/h (12 MPH)

A temperature on the information display rapidly rises to an ambient sensor-detected temperature when the following condition
is met.

- Ambient sensor-detected temperature 

≥

 Temperature on the information display

- Vehicle speed 

≥

 20 km/h (12 MPH)

- When driving more than set time
NOTE:
• After an ignition switch is turned ON, “–––” is displayed until after a 2.5 seconds.
• The ambient sensor input value that is displayed on “Data Monitor” of CONSULT is the value before the cor-

rection. It may not match the indicated temperature on the information display.

• After removal and installation of the battery and combination meter, an ambient sensor-detected tempera-

ture is indicated on the information display.

• Depending on engine heat or heat on the road surfaces, an ambient temperature may be indicated higher

than actual one.

INTERRUPT INDICATION

• The combination meter displays an interrupt regarding a warning, alert, and maintenance on the information

display, based on signals received from each unit and switch.

• When conditions are satisfied, the normal screen switches to a warning screen to display an interrupt.

Door Open Warning

• When all the following operating conditions are satisfied, the combination meter displays a door open warn-

ing on the information display by an interrupt.

Signal name

Signal path

Ignition signal

—

Ambient sensor signal

Ambient sensor 

 Combination meter

Vehicle speed signal

ABS actuator and electric unit (control unit) 

 Combination meter

MWI-22

< SYSTEM DESCRIPTION >

SYSTEM (METER SYSTEM)

• The combination meter judges showing/hiding of “door open warning”, according to the signals below:

Parking Brake Release Warning

• When all the following operating conditions are satisfied, the combination meter displays a parking brake

release warning on the information display by an interrupt.

• The combination meter judges showing/hiding of “parking brake release warning”, according to the signals

below:

Low Fuel Warning

• When all the following operating conditions are satisfied, the combination meter displays a low fuel warning

on the information display by an interrupt.

*: With the vehicle in a horizontal position

• The combination meter judges showing/hiding of “low fuel warning”, according to the signals below:

Low tire pressure warning

• The combination meter judges showing/hiding of “low tire pressure warning”, according to the signals below:

Operating condition

Ignition switch

ON

Door

Any door is open

Signal name

Signal path

Ignition signal

—

Door switch signal

Door switch 

 BCM 

 Combination meter

Operating condition

Ignition switch

ON

Parking brake

Applied

Vehicle speed

7 km/h (4.3 MPH) or more

Signal name

Signal path

Ignition signal

—

Parking brake switch signal

Parking brake switch 

 Combination meter

Vehicle speed signal

ABS actuator and electric unit (control unit) 

 Combination meter

Operating condition

Ignition switch

ON

Fuel remaining quantity

*

Approximately 11.2 

  or less (including fuel 

remained)

Signal name

Signal path

Ignition signal

—

Fuel level sensor signal

Fuel level sensor 

 Combination meter

Signal name

Signal path

Ignition signal

—

Low tire pressure warning lamp signal

BCM 

 Combination meter

MWI

SYSTEM (METER SYSTEM)

MWI-23

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

• For further information, refer to 

BCS-9, "BODY CONTROL SYSTEM : System Description"

.

Fuel filler cap warning

• The combination meter judges showing/hiding of “fuel filler cap warning”, according to the signals below:

• For further information, refer to 

MWI-18, "INFORMATION DISPLAY : System Description"

.

Low Outside Temperature (Alert)

• When all the following operating conditions are satisfied, the combination meter displays a low ambient tem-

perature on the information display by an interrupt.

• The combination meter judges showing/hiding of “low outside temperature”, according to the signals below:

Driver Alert (Alert)

• When all the following operating conditions are satisfied, the combination meter displays a driver alert on the

information display by an interrupt.

• The combination meter judges showing/hiding of “driver alert”, according to the signal below:

Service (Maintenance)

• When all the following operating conditions are satisfied, the combination meter displays a service warning

on the information display by an interrupt.

• The combination meter judges showing/hiding of “service warning”, according to the signals below:

Tire (Maintenance)

Signal name

Signal path

Ignition signal

—

Fuel filler cap warning display signal

ECM  

Combination 

meter

Operating condition

Ignition switch

ON

Ambient temperature

3 

°

C (37 

°

F) or less

information display

“ON” is selected in “SETTING”

Signal name

Signal path

Ignition signal

—

Ambient sensor signal

Ambient sensor 

 Combination meter

Operating condition

Ignition switch

Switch-ON time

Signal name

Signal path

Ignition signal

—

Operating condition

Ignition switch

ON

Mileage

More than value set in “SETTING”

Signal name

Signal path

Ignition signal

—

Vehicle speed signal

ABS actuator and electric unit (control unit)  

Combination 

meter