Nissan Qashqai J11. Manual - part 1748

 

  Index      Nissan     Nissan Qashqai J11 - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1746  1747  1748  1749   ..

 

 

Nissan Qashqai J11. Manual - part 1748

 

 

EXL-294

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

TURN SIGNAL LAMP CIRCUIT

Rear turn signal lamp

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

3.

Check continuity between BCM harness connector and ground.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-132, "Removal and Installation"

.

NO

>> Repair or replace harness.

6.

CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

+

-

Test  item

Voltage

(Approx.)

BCM

Connector

Terminal

RH

B3

136

Ground

Turn signal 
switch

Right

Center

0 V

LH

133

Left

Center

0 V

PKID0926E

PKID0926E

BCM

Continuity

Connector

Terminal

RH

E60

168

Ground

Not existed

LH

167

BCM

Continuity

Connector

Terminal

RH

M70

43

Ground

Not existed

LH

42

BCM

Continuity

Connector

Terminal

RH

B3

136

Ground

Not existed

LH

133

TURN SIGNAL LAMP CIRCUIT

EXL-295

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

3.

Check continuity between BCM harness connector and each turn signal lamp harness connector.

Front turn signal lamp

Side turn signal lamp (LHD models)

Side turn signal lamp (RHD models)

Rear turn signal lamp

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Check continuity between each turn signal lamp harness connector and ground.

Front turn signal lamp

Side turn signal lamp (LHD models)

Side turn signal lamp (RHD models)

BCM

Front combination lamp

Continuity

Connector

Terminal

Connector

Terminal

 RH

E60

168

E92

6

Existed

 LH

167

E90

BCM

Door mirror

Continuity

Connector

Terminal

Connector

Terminal

 RH

M70

43

D27

13

Existed

 LH

42

D3

BCM

Door mirror

Continuity

Connector

Terminal

Connector

Terminal

 RH

M70

43

D40

13

Existed

 LH

42

D16

BCM

Rear turn signal lamp

Continuity

Connector

Terminal

Connector

Terminal

 RH

B3

136

B80

1

Existed

 LH

133

B23

Front combination lamp

Continuity

Connector

Terminal

 RH

E92

1

Ground

Existed

 LH

E90

Door mirror

Continuity

Connector

Terminal

 RH

D27

14

Ground

Existed

 LH

D3

Door mirror

Continuity

Connector

Terminal

 RH

D40

14

Ground

Existed

 LH

D16

EXL-296

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

TURN SIGNAL LAMP CIRCUIT

Rear turn signal lamp

Is the inspection result normal?

YES-1 >> Front turn signal lamp or rear turn signal lamp: GO TO 8.
YES-2 >> Side turn signal lamp: Replace side turn signal lamp. Refer to 

EXL-323, "Removal and Installa-

tion"

.

NO

>> Repair or replace harness.

8.

CHECK TURN SIGNAL LAMP BULB

Check the applicable turn signal lamp bulb.

Is the inspection result normal?

YES

>> Check the corresponding turn signal lamp bulb socket. Repair or replace if necessary.

NO

>> Replace the corresponding turn signal lamp bulb. Refer to 

EXL-319, "Replacement"

 (front turn

signal lamp) or 

EXL-331, "Replacement"

 (rear turn signal lamp).

Rear turn signal lamp

Continuity

Connector

Terminal

 RH

B80

2

Ground

Existed

 LH

B23

LIGHT & RAIN SENSOR

EXL-297

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LIGHT & RAIN SENSOR

Component Function Check

INFOID:0000000010469994

1.

CHECK LIGHT & RAIN SENSOR

1.

Clean light & rain sensor detection area of windshield fully.

2.

Turn ignition switch ON.

3.

Turn lighting switch AUTO.

4.

With the light & rain sensor illuminating, check the auto light function. 

Is the inspection result normal?

YES

>> Light & rain sensor is normal.

NO

>> Refer to 

EXL-297, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010469995

1.

CHECK LIGHT & RAIN SENSOR POWER SUPPLY

1.

Turn ignition switch OFF

2.

Disconnect light & rain sensor connector.

3.

Turn ignition switch ON.

4.

Check voltage between light & rain sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK LIGHT & RAIN SENSOR POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Remove room lamp relay.

3.

Check continuity between room lamp relay harness connector and light & rain sensor harness connector.

Is the inspection result normal?

YES

>> Perform the interior room lamp power supply circuit diagnosis. Refer to 

INL-55, "Diagnosis Proce-

dure"

.

NO

>> Repair or replace harness.

3.

CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT

Check continuity between light & rain sensor harness connector and ground.

Condition

Auto light function

Light & rain sensor

When illuminating

Not operating

When shutting off light

Operating

+

-

Voltage

Light & rain sensor

Connector

Terminal

R5

1

Ground Battery 

voltage

Room lamp relay

Light & rain sensor

Continuity

Connector

Terminal

Connector

Terminal

M80

7

R5

1

Existed

Light & rain sensor

Continuity

Connector

Terminal

R5

3

Ground

Existed

 

 

 

 

 

 

 

Content   ..  1746  1747  1748  1749   ..