Nissan Qashqai J11. Manual - part 1516

PWC-44

< DTC/CIRCUIT DIAGNOSIS >

REAR POWER WINDOW SWITCH

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-68, "POWER WINDOW MAIN SWITCH :

Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.
Refer to 

PWC-44, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace rear power window switch. Refer to 

PWC-69, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010286501

1.

CHECK REAR POWER WINDOW SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch connector.

3.

Check rear power window switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace rear power window switch. Refer to 

PWC-69, "Removal and Installation"

.

Power window main switch

Ground

Continuity

Connector

Terminal

D10 (LHD models)

D30 (RHD models)

8

Not existed

9

6

7

Rear power window switch

Condition

Continuity

Terminal

1

5

UP

Existed

3

4

3

4

NEUTRAL

2

5

1

4

DOWN

2

5

POWER WINDOW MOTOR

PWC-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

POWER WINDOW MOTOR

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000010325683

1.

 CHECK FUNCTION

Check front power window motor (driver side) operation with power window main switch.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-45, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000010286502

LHD MODELS

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between front power window motor (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window motor (driver side). Refer to 

GW-26, "Disassembly and Assembly"

.

NO

>> GO TO 2.

2.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-68, "POWER WINDOW MAIN SWITCH :

Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(

−

)

Condition

Voltage

Front power window motor (driver side)

Connector

Terminal

D12

3

Ground

Power window main 
switch

UP

0 - 1 V

DOWN

9 - 16 V

4

UP

9 - 16 V

DOWN

0 - 1 V

 Power window main switch

Front power window motor (driver side)

Continuity

Connector

Terminal

Connector

Terminal

D11

17

D12

4

Existed

19

3

Power window main switch

Ground

Continuity

Connector

Terminal

D11

17

Not existed

19

PWC-46

< DTC/CIRCUIT DIAGNOSIS >

POWER WINDOW MOTOR

RHD MODELS

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between front power window motor (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window motor (driver side). Refer to 

GW-26, "Disassembly and Assembly"

.

NO

>> GO TO 2.

2.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-68, "POWER WINDOW MAIN SWITCH :

Removal and Installation"

.

NO

>> Repair or replace harness.

PASSENGER SIDE

PASSENGER SIDE : Component Function Check

INFOID:0000000010325684

1.

 CHECK FUNCTION

Check front power window motor (passenger side) operation with power window main switch (passenger side
switch) or front power window switch (passenger side).

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-46, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000010286503

LHD MODELS

(+)

(

−

)

Condition

Voltage

Front power window motor (driver side)

Connector

Terminal

D32

3

Ground

Power window main 
switch

UP

0 - 1 V

DOWN

9 - 16 V

4

UP

9 - 16 V

DOWN

0 - 1 V

 Power window main switch

Front power window motor (driver side)

Continuity

Connector

Terminal

Connector

Terminal

D31

17

D32

4

Existed

19

3

Power window main switch

Ground

Continuity

Connector

Terminal

D31

17

Not existed

19

POWER WINDOW MOTOR

PWC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

1.

CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (passenger side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between front power window motor (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window motor (passenger side). Refer to 

GW-26, "Disassembly and Assem-

bly"

.

NO

>> GO TO 2.

2.

CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) connector.

3.

Check continuity between front power window switch (passenger side) harness connector and front power
window motor (passenger side) harness connector.

4.

Check continuity between front power window switch (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window switch (passenger side). Refer to 

PWC-68, "FRONT POWER WIN-

DOW SWITCH (PASSENGER SIDE) : Removal and Installation"

.

NO

>> Repair or replace harness.

RHD MODELS

1.

CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (passenger side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between front power window motor (passenger side) harness connector and ground.

(+)

(

−

)

Condition

Voltage

Front power window motor (passenger side)

Connector

Terminal 

D35

1

Ground

Front power window 
switch
(passenger side)

UP

9 - 16 V

DOWN

0 - 1 V

2

UP

0 - 1 V

DOWN

9 - 16 V

Front power window switch (passenger side)

Front power window motor (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

D37

6

D35

2

Existed

7

1

Front power window switch (passenger side)

Ground

Continuity

Connector

Terminal

D37

6

Not existed

7