Nissan Qashqai J11. Manual - part 1496

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

SEC-283

< SYMPTOM DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SYMPTOM DIAGNOSIS

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

Description

INFOID:0000000010338082

Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to 

SEC-237, "Work Flow"

.

• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-

TIONS)” before starting diagnosis, and check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

Ignition switch is not in the ON position.

Diagnosis Procedure

INFOID:0000000010505355

1.

CHECK SECURITY INDICATOR LAMP

Check security indicator lamp.
Refer to 

SEC-169, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

REPLACE BCM

Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

Is the result normal?

YES

>> INSPECTION END.

NO

>> GO TO 3

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> INSPECTION END

NO

>> GO TO 4.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

SEC-284

< SYMPTOM DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

VEHICLE SECURITY SYSTEM CANNOT BE SET

VEHICLE SECURITY SYSTEM CANNOT BE SET

KEY FOB

KEY FOB : Description

INFOID:0000000010338084

Armed phase is not activated when all doors are locked using keyfob.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.

KEY FOB : Diagnosis Procedure

INFOID:0000000010338085

1.

CHECK REMOTE KEYLESS ENTRY SYSTEM

Lock/unlock door with keyfob. Refer to 

DLK-391, "REMOTE KEYLESS ENTRY FUNCTION : System Descrip-

tion"

 (With super lock) or 

DLK-517, "System Description"

 (With out super lock).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

DLK-448, "Diagnosis Procedure"

.

2.

CHECK HOOD SWITCH

Check hood switch. Refer to 

SEC-274, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace hood switch.

3.

REPLACE BCM

• Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

• Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

DOOR LOCK AND UNLOCK SWITCH

DOOR LOCK AND UNLOCK SWITCH : Description

INFOID:0000000010338086

ARMED phase is not activated when door is locked using door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.

CONDITION OF VEHICLE (OPERATING CONDITION)

• SECURITY ALARM SET: ON

Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT. 

DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure

INFOID:0000000010338087

1.

CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)

Lock/unlock door with door lock and unlock switch. Refer to 

DLK-389, "System Description"

 (With super lock)

or 

DLK-515, "System Description"

 (Without super lock).

Is the inspection result normal?

YES

>> GO TO 2.

VEHICLE SECURITY SYSTEM CANNOT BE SET

SEC-285

< SYMPTOM DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

NO

>> Check power door lock system (door lock function). Refer to 

DLK-443, "ALL DOOR : Diagnosis

Procedure"

 (With super lock) or 

DLK-581, "ALL DOOR : Diagnosis Procedure"

 (Without super

lock).

2.

CHECK HOOD SWITCH

Check hood switch. Refer to 

SEC-274, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or Replace hood switch.

3.

REPLACE BCM

• Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

• Confirm the operation after replacement.
Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

UNLOCK SENSOR

UNLOCK SENSOR : Description

INFOID:0000000010506179

Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.

UNLOCK SENSOR : Diagnosis Procedure

INFOID:0000000010506180

1.

CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)

Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to 

DLK-389, "System Description"

 (With super lock) or 

DLK-515, "System Description"

 (Without super

lock).
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check power door lock system (door lock function). Refer to 

DLK-447, "Diagnosis Procedure"

(With super lock) or 

DLK-585, "Diagnosis Procedure"

 (Without super lock).

2.

CHECK HOOD SWITCH

Check hood switch.
Refer to 

SEC-274, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace hood switch.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

SEC-286

< SYMPTOM DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

VEHICLE SECURITY ALARM DOES NOT ACTIVATE

VEHICLE SECURITY ALARM DOES NOT ACTIVATE

Description

INFOID:0000000010338088

Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITIONS)

“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.

Diagnosis Procedure

INFOID:0000000010505375

1.

CHECK SENSOR CANCEL SWITCH

Check sensor cancel switch.
Refer to 

SEC-279, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace sensor cancel switch.

2.

PERFORM SELF-DIAGNOSIS OF SIREN CONTROL UNIT

Perform self-diagnosis of siren control unit.
Refer to 

SEC-207, "Diagnosis Description"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK DOOR SWITCH

Check door switch.
Refer to 

DLK-430, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace the malfunctioning door switch. Refer to 

DLK-195, "Removal and Installation"

.

4.

CHECK HOOD SWITCH

Check hood switch.
Refer to 

SEC-274, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace hood switch.

5.

CHECK INTRUDER SENSOR

Check intruder sensor.
Refer to 

SEC-277, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace intruder sensor.

6.

REPLACE SIREN CONTROL UNIT

1.

Replace siren control unit.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 7.