Nissan Juke (2012 year). Service Repair Manual

TM-252

< SERVICE DATA AND SPECIFICATIONS (SDS)

[CVT: RE0F10B]

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

General Specification

INFOID:0000000007576595

*1: Refer to

MA-10, "Fluids and Lubricants"

*2: The fluid capacity is the reference value. Check the fluid level with CVT fluid level gauge.

Shift Characteristics

INFOID:0000000007576596

Numerical value data are reference values.

Unit: rpm

*: With Integrated Control System

CAUTION:

Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).

Stall Speed

INFOID:0000000007576597

Line Pressure

INFOID:0000000007576598

Unit: kPa (bar, kg/cm

, psi)

*: Reference values

Applied model

MR16DDT

2WD

AWD

CVT model

RE0F10B

CVT assembly

Model code number

3TX0A

3TX0C

Transmission gear ratio

D range

2.349 – 0.394

Reverse

1.750

Final drive

5.798

Recommended fluid

NISSAN CVT Fluid NS-2

Fluid capacity

8.2 liter (8-5/8 US qt, 7-1/4 Imp qt)

8.6 liter (9-1/8 US qt, 7-5/8 Imp qt)

CAUTION:

• Use only Genuine NISSAN CVT Fluid NS-2. Never mix with other fluid.
• Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT durability, and may dam-

age the CVT, which is not covered by the NISSAN new vehicle limited warranty.

Throttle position

Shift pattern

Engine speed

At 40 km/h (25 MPH)

At 60 km/h (37 MPH)

2/8

“D” position

1,500 – 3,100

1,600 – 3,400

SPORT mode*

2,200 – 3,000

2,800 – 3,600

ECO mode*

1,500 – 2,400

1,600 – 2,500

8/8

“D” position

3,300 – 4,200

4,300 – 5,200

SPORT mode*

3,300 – 4,200

4,300 – 5,200

ECO mode*

3,300 – 4,200

4,300 – 5,200

Stall speed

3,000 – 3,500 rpm

Engine speed

Line pressure

“R” and “D” positions

At idle

750 (7.50, 7.65, 108.8)

At stall

5,700 (57.00, 58.14, 826.5)

Revision: 2011 October

2012 JUKE

SERVICE DATA AND SPECIFICATIONS (SDS)

TM-253

< SERVICE DATA AND SPECIFICATIONS (SDS)

[CVT: RE0F10B]

Torque Converter

INFOID:0000000007576599

Heater Thermostat

INFOID:0000000007576600

Standard

Dimension between end of converter housing and torque converter

14.4 mm (0.567 in)

Valve opening temperature

69 – 73

C (156 –163

Maximum valve lift

5.0 mm/85

C (0.197 in/185

Valve closing temperature

C (149

Revision: 2011 October

2012 JUKE

VTL-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000007824885

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Revision: 2011 October

2012 JUKE

PREPARATION

VTL-3

< PREPARATION >

VTL

PREPARATION

Commercial Service Tool

INFOID:0000000007580063

Tool name

Description

Remover tool

Remove clips, pawls, and metal clips

JMKIA3050ZZ

Revision: 2011 October

2012 JUKE

VTL-4

< SYSTEM DESCRIPTION >

VENTILATION SYSTEM

SYSTEM DESCRIPTION

VENTILATION SYSTEM

System Description

INFOID:0000000007580064

OUTLINE

Ventilation system is controlled by A/C auto amp. (AUTOMATIC AIR CONDITIONING) or A/C control (MAN-
UAL AIR CONDITIONING). For details of air conditioner system, refer to

HAC-11, "System Description"

(AUTOMATIC AIR CONDITIONING),

HAC-99, "System Description"

(MANUAL AIR CONDITIONING).

AIR FLOW

Front

Rear

Models for Canada

: Applicable

Models except for Canada

JMIIA1224ZZ

JMIIA0870ZZ

MODE/DEF position

indication

AIR OUTRET

Ventilator

Foot

Defroster (4)

Center (1)

Side (2)

Front (3)

Rear (3)

—

Revision: 2011 October

2012 JUKE

VENTILATION SYSTEM

VTL-5

< SYSTEM DESCRIPTION >

VTL

MODE/DEF position in-

dication

AIR OUTRET

Ventilator

Foot (3)

Defroster (4)

Center (1)

Side (2)

—

Revision: 2011 October

2012 JUKE

VTL-6

< REMOVAL AND INSTALLATION >

DUCT AND GRILLE

REMOVAL AND INSTALLATION

DUCT AND GRILLE

Exploded View

INFOID:0000000007580065

FRONT

REAR

A/C unit assembly

Side ventilator duct LH

Foot duct LH

Side defroster nozzle LH

Side ventilator grille LH

Side defroster grille LH

Instrument panel assembly

Center ventilator grille LH

Cluster lid C

10. Center ventilator grille RH

11. Side defroster grille RH

12. Side ventilator grille RH

13. Center ventilator duct

14. Front defroster nozzle

15. Instrument panel bracket

16. Side defroster nozzle RH

17. Foot duct RH

18. Side ventilator duct RH

: Pawl

JMIIA1040ZZ

Revision: 2011 October

2012 JUKE

DUCT AND GRILLE

VTL-7

< REMOVAL AND INSTALLATION >

VTL

*: Models for Canada only

CENTER VENTILATOR GRILLE

CENTER VENTILATOR GRILLE : Removal and Installation

INFOID:0000000007580066

REMOVAL

Remove cluster lid C. Refer to

IP-12, "Removal and Installation"

Remove fixing screws (A).

A/C unit assembly

Rear heater duct 1 LH*

Rear heater duct 2 LH*

Rear heater duct 3 LH*

Rear heater duct 1 RH*

Rear heater duct 2 RH*

Rear heater duct 3 RH*

: Pawl

JMIIA0838ZZ

JMIIA0839ZZ

Revision: 2011 October

2012 JUKE

VTL-8

< REMOVAL AND INSTALLATION >

DUCT AND GRILLE

Disengage fixing pawls (A), and then remove center ventilator
grille.

INSTALLATION

Install in the reverse order of removal.

SIDE DEFROSTER NOZZLE

SIDE DEFROSTER NOZZLE : Removal and Installation

INFOID:0000000007580067

REMOVAL

Driver Side

Remove instrument panel assembly. Refer to

IP-12, "Removal and Installation"

Remove fixing screws (A), and then remove side defroster noz-
zle.

Passenger Side

Remove instrument panel assembly. Refer to

IP-12, "Removal and Installation"

Remove fixing screws (A), and then remove instrument panel
bracket (1).

Remove fixing screw (B), and then remove side defroster nozzle
(2).

INSTALLATION

Install in the reverse order of removal.

SIDE VENTILATOR GRILLE

SIDE VENTILATOR GRILLE : Removal and Installation

INFOID:0000000007580068

REMOVAL

Remove instrument panel assembly. Refer to

IP-12, "Removal and Installation"

JMIIA0840ZZ

JMIIA1042ZZ

JMIIA1041ZZ

Revision: 2011 October

2012 JUKE

DUCT AND GRILLE

VTL-9

< REMOVAL AND INSTALLATION >

VTL

Remove fixing screws (A), and then remove side ventilator grille.

INSTALLATION

Install in the reverse order of removal.

SIDE DEFROSTER GRILLE

SIDE DEFROSTER GRILLE : Removal and Installation

INFOID:0000000007580069

REMOVAL

Remove instrument panel assembly. Refer to

IP-12, "Removal and Installation"

Remove side defroster nozzle. Refer to

VTL-8, "SIDE DEFROSTER NOZZLE : Removal and Installation"

Remove fixing screw (A) and disengage fixing pawl (B), and
then remove side defroster grille.

INSTALLATION

Install in the reverse order of removal.

FRONT DEFROSTER NOZZLE

FRONT DEFROSTER NOZZLE : Removal and Installation

INFOID:0000000007580070

REMOVAL

Remove instrument panel assembly. Refer to

IP-12, "Removal and Installation"

Remove side defroster nozzle. Refer to

VTL-8, "SIDE DEFROSTER NOZZLE : Removal and Installation"

Remove fixing screw (A), and then remove front defroster noz-
zle.

INSTALLATION

Install in the reverse order of removal.

CENTER VENTILATOR DUCT

JMIIA0845ZZ

JMIIA0846ZZ

JMIIA0843ZZ

Revision: 2011 October

2012 JUKE

VTL-10

< REMOVAL AND INSTALLATION >

DUCT AND GRILLE

CENTER VENTILATOR DUCT : Removal and Installation

INFOID:0000000007580071

REMOVAL

Remove instrument panel assembly. Refer to

IP-12, "Removal and Installation"

Remove side defroster nozzle LH and RH. Refer to

VTL-8, "SIDE DEFROSTER NOZZLE : Removal and

Installation"

Remove front defroster nozzle. Refer to

VTL-9, "FRONT DEFROSTER NOZZLE : Removal and Installa-

tion"

Remove fixing screws (A), and then remove center ventilator
duct.

INSTALLATION

Install in the reverse order of removal.

SIDE VENTILATOR DUCT

SIDE VENTILATOR DUCT : Removal and Installation

INFOID:0000000007580072

REMOVAL

Remove instrument panel assembly. Refer to

IP-12, "Removal and Installation"

Remove fixing screws (A), and then remove side ventilator duct.

INSTALLATION

Install in the reverse order of removal.

REAR HEATER DUCT 1

REAR HEATER DUCT 1 : Removal and Installation

INFOID:0000000007580073

REMOVAL

Remove center console assembly. Refer to

IP-22, "Removal and Installation"

JMIIA1043ZZ

Driver side

Passenger side

JMIIA0847ZZ

Revision: 2011 October

2012 JUKE

DUCT AND GRILLE

VTL-11

< REMOVAL AND INSTALLATION >

VTL

Disengage fixing pawls, and then remove rear heater duct 1.
(Models for Canada only)

INSTALLATION

Install in the reverse order of removal.

REAR HEATER DUCT 2

REAR HEATER DUCT 2 : Removal and Installation

INFOID:0000000007580074

REMOVAL

Remove center console assembly. Refer to

IP-22, "Removal and Installation"

Remove front seat assmbly. Refer to

SE-18, "Removal and Installation"

Remove front kicking plate inner and rear kicking plate inner. Refer to

INT-18, "KICKING PLATE INNER :

Removal and Installation"

Remove center pillar lower garnish. Refer to

INT-21, "CENTER PILLAR LOWER GARNISH : Removal

and Installation"

Remove dash side finisher. Refer to

INT-20, "DASH SIDE FINISHER : Removal and Installation"

Remove rear heater duct 2. (Models for Canada only)
• Peel off floor carpet (1).
• Remove rear heater duct 3 (2) from rear heater duct 2 (3).

• Remove front floor spacer, and then remove rear heater duct 2

(2) from rear heater duct 1 (1).

INSTALLATION

Install in the reverse order of removal.

REAR HEATER DUCT 3

REAR HEATER DUCT 3 : Removal and Installation

INFOID:0000000007580075

REMOVAL

: Pawl

JMIIA0848ZZ

: Vehicle front

JMIIA0849ZZ

: Vehicle front

JMIIA0850ZZ

Revision: 2011 October

2012 JUKE

VTL-12

< REMOVAL AND INSTALLATION >

DUCT AND GRILLE

Remove center console assembly. Refer to

IP-22, "Removal and Installation"

Remove front seat assmbly. Refer to

SE-18, "Removal and Installation"

Remove front kicking plate inner and rear kicking plate inner. Refer to

INT-18, "KICKING PLATE INNER :

Removal and Installation"

Remove center pillar lower garnish. Refer to

INT-21, "CENTER PILLAR LOWER GARNISH : Removal

and Installation"

Remove dash side finisher. Refer to

INT-20, "DASH SIDE FINISHER : Removal and Installation"

Remove rear heater duct 3. (Models for Canada only)
• Peel off floor carpet (1).
• Remove rear floor spacer, and then remove rear heater duct 3

(2) from rear heater duct 2 (3).

INSTALLATION

Install in the reverse order of removal.

FOOT DUCT

FOOT DUCT : Removal and Installation

INFOID:0000000007580076

REMOVAL

Driver Side

Remove instrument lower panel LH. Refer to

IP-12, "Removal and Installation"

Disconnect harness connector.

Remove harness connector fixing clamp.

Remove fixing screws, and then remove foot duct LH.

Passenger Side

Remove glove box assembly. Refer to

IP-12, "Removal and Installation"

Remove fixing screws, and then remove foot duct RH.

INSTALLATION

Install in the reverse order of removal.

: Vehicle front

JMIIA0849ZZ

Revision: 2011 October

2012 JUKE

BLOWER MOTOR

VTL-13

< REMOVAL AND INSTALLATION >

VTL

BLOWER MOTOR

Exploded View

INFOID:0000000007580077

• *1: Manual air conditioning

• *2: Automatic air conditioning

Removal and Installation

INFOID:0000000007580078

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or the electric tools for servicing.

REMOVAL

Remove glove box assembly. Refer to

IP-12, "Removal and Installation"

Disconnect blower motor harness connector (1) and front pas-
senger air bag module harness connector (2).

Remove front passenger air bag module. Refer to

SR-16, "Removal and Installation"

A/C unit assembly

Blower fan resistor

Sub harness

Power transistor

Sub harness

Blower motor

JPIIA1549ZZ

JMIIA1044ZZ

Revision: 2011 October

2012 JUKE

VTL-14

< REMOVAL AND INSTALLATION >

BLOWER MOTOR

Press flange holding hook (A), and then turn blower motor (1)
clockwise.

Pull outside, and then remove blower motor.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never use the old mounting bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioningparts, reset the memory using self-diagnosis or CONSULT-III. Refer to

SRC-11, "On Board

Diagnosis Function"

SRC-16, "CONSULT Function"

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

JPIIA1692ZZ

Revision: 2011 October

2012 JUKE

Nissan Juke (2012 year). Service Repair Manual - part 236