Nissan Juke (2016 year). Service Repair Manual - part 578

CURTAIN AIR BAG MODULE

SR-23

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

• Insert metal clips of front roof until a locking sound is heard. Pull metal clips and check that it is fully

locked to the vehicle body.

• Check perforation of curtain air bag module to check that curtain air bag module is not twisted.

• Never damage the harness while installing.

• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-10, "On Board Diag-

nosis Function"

 or 

SRC-15, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

Revision: November 2015

2016 JUKE

SR-24

< REMOVAL AND INSTALLATION >

CRASH ZONE SENSOR

CRASH ZONE SENSOR

Exploded View

INFOID:0000000012199977

Removal and Installation

INFOID:0000000012199978

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Never use the air tools or electric tools for servicing.

REMOVAL

1. Remove front center grille fixing clips. Refer to 

EXT-26, "Removal and Installation"

.

1.

Crash zone sensor

2.

Bracket

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA1616GB

Revision: November 2015

2016 JUKE

CRASH ZONE SENSOR

SR-25

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

2. Pull back front center grille, it makes work space.

3. Remove the crash zone sensor fixing nuts (A), and then pull the

bracket (1) and crash zone sensor (2) for vehicle front.

4. Disconnect the crash zone sensor harness connector, and then remove crash zone sensor.

CAUTION:

• Never impact the crash zone sensor.

• Replace the crash zone sensor if it has been dropped or sus-

tained an impact.

• Replace the crash zone sensor of deployed driver air bag, deployed passenger air bag, seat belt pre-

tensioner and deployed lap pre-tensioner.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never use the old fixing nut after removal, replace with the new nut.

• Never damage the harness while installing.

• Always install normally aligning to the cutout hole, because performance of the crash zone sensor

excessively fluctuates according to the installation position.

• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-10, "On Board Diag-

nosis Function"

 or 

SRC-15, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

JMHIA1617ZZ

JMHIA1618ZZ

JMHIA0009ZZ

Revision: November 2015

2016 JUKE

SR-26

< REMOVAL AND INSTALLATION >

SATELLITE SENSOR

SATELLITE SENSOR

Exploded View

INFOID:0000000012199979

Removal and Installation

INFOID:0000000012199980

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Never use the air tools or electric tools for servicing.

FRONT SATELLITE SENSOR

Removal

1. Remove the front door finisher. Refer to 

INT-13, "Removal and Installation"

.

2. Remove sealing screen (lower side).

NOTE:

Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing

screen is reused.

1.

Front satellite sensor

2.

Front door inner panel

3.

Satellite sensor bracket

4.

Center pillar inner panel

5.

Rear satellite sensor

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA1805GB

Revision: November 2015

2016 JUKE

SATELLITE SENSOR

SR-27

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

3. Remove the front satellite sensor mounting nuts (A), and then

pull the front satellite sensor (1).

4. Disconnect the harness connector and then remove the front satellite sensor. 

CAUTION:

• Never impact the front satellite sensor.

• Replace the front satellite sensor if it has been dropped or

sustained an impact.

• Replace the front satellite sensor of deployed side air bag module and deployed curtain air bag mod-

ule. 

Installation

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never use the old fixing nuts after removal, replace with the new nuts.

• Never damage the harness while installing.

• Always install normally aligning to the cutout hole, because performance of the front satellite sensor

excessively fluctuates according to the installation position.

• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-10, "On Board Diag-

nosis Function"

 or 

SRC-15, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

REAR SATELLITE SENSOR

Removal

1. Remove the center pillar lower garnish. Refer to 

INT-22, "CENTER PILLAR LOWER GARNISH : Removal

and Installation"

.

2. Remove the rear satellite sensor mounting nut (A), and then pull

the rear satellite sensor (1).

3. Disconnect the harness connector and then remove the rear satellite sensor. 

JMHIA1806ZZ

JMHIA0009ZZ

JMHIA1620ZZ

Revision: November 2015

2016 JUKE

SR-28

< REMOVAL AND INSTALLATION >

SATELLITE SENSOR

CAUTION:

• Never impact the rear satellite sensor.

• Replace the rear satellite sensor if it has been dropped or sus-

tained an impact.

• Replace the rear satellite sensor of deployed side air bag module and deployed curtain air bag mod-

ule. 

Installation

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never use the old fixing nut after removal, replace with the new nut.

• Never damage the harness while installing.

• Always install normally aligning to the cutout hole, because performance of the rear satellite sensor

excessively fluctuates according to the installation position.

• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-10, "On Board Diag-

nosis Function"

 or 

SRC-15, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

JMHIA0009ZZ

Revision: November 2015

2016 JUKE

DIAGNOSIS SENSOR UNIT

SR-29

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

DIAGNOSIS SENSOR UNIT

Exploded View

INFOID:0000000012199981

Removal and Installation

INFOID:0000000012199982

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-

ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by

static electricity and pre-tensioner seat belt operation.

• Never use the air tools or electric tools for servicing.

• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-

est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the

air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags

and seat belt pre-tensioners in a collision resulting in serious personal injury or death.

REMOVAL

1. Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using

CONSULT.

2. Disconnect the each connector of all air bag modules and pre-tensioner seat belts.

1.

Diagnosis sensor unit

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA3047GB

Revision: November 2015

2016 JUKE

SR-30

< REMOVAL AND INSTALLATION >

DIAGNOSIS SENSOR UNIT

3. Remove the center console assembly. Refer to 

IP-24, "Removal and Installation"

.

4. Disconnect the diagnosis sensor unit harness connectors (A).
5. Remove the diagnosis sensor unit mounting bolts (B), and then

remove the diagnosis sensor unit.

CAUTION:

• Never impact the diagnosis sensor unit.

• Replace the diagnosis sensor unit if it has been dropped or

sustained an impact.

• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-

sioner.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never use the old bolts after removal, replace with the new bolts.

• Never damage the harness while installing.

• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-10, "On Board Diag-

nosis Function"

 or 

SRC-15, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

• After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-

nated number (identification number) of the new replacement air bag sensor unit matches the ECU

discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.

NOTE:

If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU

discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify

that the correct air bag diagnosis sensor unit was installed.

JMHIA1624ZZ

JMHIA0009ZZ

Revision: November 2015

2016 JUKE