Nissan Juke (2016 year). Service Repair Manual - part 577

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     575      576      577      578     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 577

 

 

SPIRAL CABLE

SR-15

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

SPIRAL CABLE

Exploded View

INFOID:0000000012199971

Removal and Installation

INFOID:0000000012199972

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Never use the air tools or electric tools for servicing.

1.

Steering column upper cover

2.

Steering column assembly

3.

Steering column lower cover

4.

Side lid LH

5.

TORX bolt

6.

Driver air bag module

7.

TORX bolt

8.

Side lid RH

9.

Steering wheel

10. Spiral cable

11. Steering angle sensor

12. Combination switch

13. Steering switch

: Pawl

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

JMHIA1655GB

Revision: November 2015

2016 JUKE

SR-16

< REMOVAL AND INSTALLATION >

SPIRAL CABLE

REMOVAL

1. Remove driver air bag module. Refer to 

SR-12, "Removal and Installation"

.

2. Remove steering wheel. Refer to 

ST-9, "Removal and Installation"

.

3. Remove steering column upper cover and steering column lower cover. Refer to 

IP-13, "Removal and

Installation"

.

4. Disconnect the spiral cable body side harness connectors (A),

(B) and steering angle sensor harness connectors (C).

NOTE:

Disconnect the spiral cable body side harness connector (B)

after removing the spiral cable (A).

5. Remove the spiral cable fixing screws.
6. Remove the spiral cable fixing pawls with remover tool (A).

CAUTION:

Remove pawls slowly so that they are not damaged.

7. Remove the steering angle sensor. Refer to 

BRC-156, "Removal and Installation"

.

CAUTION:

• Never impact the spiral cable.

• Replace the spiral cable if it is dropped or sustains an impact.

• Never disassemble the spiral cable.

• Never apply lubricant to the spiral cable.

• Never allow oil, grease, detergent, or water to come in contact with the spiral cable.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

JMHIA1656ZZ

: Pawl

JMHIA1610ZZ

JMHIA0009ZZ

Revision: November 2015

2016 JUKE

SPIRAL CABLE

SR-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

• The spiral cable may snap during steering operation if the

cable is installed in an improper position.

The neutral position is set as per the following.

• Carefully turn the spiral cable clockwise to the end position.

Then turn it counterclockwise (about 2 and a half turns) and

stop turning at the mark (B) when the stopper insertion holes

are in the same position.

• The service part is installed in the neutral position by the

stopper and can be set without adjusting after the stopper is

removed.

• Never over turn the spiral cable or go beyond the number of

turns required. (This causes the cable to snap)

• Adjust the spiral cable locating pin (A) to the steering wheel

locating pin hole (C).

• Fix the driver air bag module harnesses to the harness fixing

hook (A).

• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-10, "On Board Diag-

nosis Function"

 or 

SRC-15, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

JMHIA0879ZZ

JMHIA1608ZZ

Revision: November 2015

2016 JUKE

SR-18

< REMOVAL AND INSTALLATION >

PASSENGER AIR BAG MODULE

PASSENGER AIR BAG MODULE

Exploded View

INFOID:0000000012199973

Removal and Installation

INFOID:0000000012199974

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Always work from the side of air bag module. Never work in front of it.

• Never use the air tools or the electric tools for servicing.

REMOVAL

1. Remove instrument side finisher RH, glove box lid, and glove box assembly. Refer to 

IP-13, "Removal and

Installation"

.

1.

Passenger air bag module

2.

Instrument panel assembly

: Pawl

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA1657GB

Revision: November 2015

2016 JUKE

PASSENGER AIR BAG MODULE

SR-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

2. Disconnect passenger air bag module harness connector (A)

from passenger air bag module.

3. Remove passenger air bag module fixing bolts (B).

4. Put a hand to back of instrument panel (glove box opening), dis-

engage connections of the passenger air bag module pawls

from the inside of the vehicle toward the outside, and remove.

CAUTION:

• Never insert a remover tool between passenger air bag

module and instrument panel assembly. Doing so may

cause damage.

• Wear gloves.

CAUTION:

• Always place the passenger air bag module with pad side fac-

ing upward.

• Never impact the passenger air bag module.

• Replace the passenger air bag module if it has been dropped

or sustained an impact.

• Never insert any foreign objects (screwdriver, etc.) into the passenger air bag module.

• Never disassemble the passenger air bag module.

• Never expose the passenger air bag module to temperatures exceeding 90 

°

C (194 

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the passenger air bag module.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never use the old fixing bolts after removal, replace with the new bolts.

• Never damage the harness while installing.

JMHIA1658ZZ

: Pawl

JMHIA1659ZZ

: Upward

JMHIA1613ZZ

JMHIA0009ZZ

Revision: November 2015

2016 JUKE

SR-20

< REMOVAL AND INSTALLATION >

PASSENGER AIR BAG MODULE

• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-10, "On Board Diag-

nosis Function"

 or 

SRC-15, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

Revision: November 2015

2016 JUKE

CURTAIN AIR BAG MODULE

SR-21

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

CURTAIN AIR BAG MODULE

Exploded View

INFOID:0000000012199975

Removal and Installation

INFOID:0000000012199976

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Always work from the side of curtain air bag module. Never work in front of it.

• Never use the air tools or electric tools for servicing.

REMOVAL

1. Remove headlining assembly.

• Normal roof models: Refer to 

INT-27, "NORMAL ROOF : Removal and Installation"

.

• Sunroof models: Refer to 

INT-30, "SUNROOF : Removal and Installation"

.

2. Remove the curtain air bag module mounting bolt that is located on the front pillar.

1.

Curtain air bag module

: Metal clip

: N·m (kg-m, ft-lb)

JMHIA1614GB

Revision: November 2015

2016 JUKE

SR-22

< REMOVAL AND INSTALLATION >

CURTAIN AIR BAG MODULE

3. Disengage metal clips on the front roof.

1. Fully insert a flat-bladed screwdriver (A) into center of metal clip.

2. Lift the flat-bladed screwdriver upward as shown in the figure and disengage upper side of metal clip.

3. Rotate the flat-bladed screwdriver as shown in the figure and disengage lower side of metal clip.

CAUTION:

Never deform metal clip.

4. Disconnect curtain air bag harness connector.

CAUTION:

• For installing/removing the curtain air bag harness con-

nector, insert thin screwdriver wrapped in tape into notch,

lift lock and remove the connector.

• Install the connector with lock raised, and push lock into

the connector.

• After installing the connector, check that the lock is

pushed securely into it.

5. Remove the curtain air bag module mounting bolts that are located on the rear pillar.
6. Remove the curtain air bag module mounting bolts that are located on the center pillar.
7. Remove the curtain air bag module mounting bolts that are located on the inflator, and then remove cur-

tain air bag module.

CAUTION:

• Never impact the curtain air bag module.

• Replace the curtain air bag module if it has been dropped or

sustained an impact.

• Never insert any foreign objects (screwdriver, etc.) into the curtain air bag module.

• Never disassemble the curtain air bag module.

• Never expose the curtain air bag module to temperatures exceeding 90 

°

C (194 

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the curtain air bag module.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

: Metal clip

JMHIA1615ZZ

PHIA0953J

JMHIA0009ZZ

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     575      576      577      578     ..