Nissan Juke (2016 year). Service Repair Manual - part 534

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     532      533      534      535     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 534

 

 

CHECK ANTI-PINCH FUNCTION

PWC-27

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

CHECK ANTI-PINCH FUNCTION

Description

INFOID:0000000012196913

If any of the following operations are performed, the initialization is necessary for normal operation of anti-

pinch function. Refer to 

PWC-27, "Work Procedure"

.

• Disconnection and connection of battery cable from negative terminal.

• When power window main switch replaced.

• Electric power supply to power window main switch or power window motor (driver side) is interrupted by

blown fuse or disconnection and connection of the negative terminal of battery, etc.

• Disconnection and connection of power window main switch harness connector.

• Removal of power window motor (driver side) from regulator assembly.

• Operation of regulator assembly as an independent unit.

• Removal and installation of glass.

• Removal and installation of door glass run.

Work Procedure

INFOID:0000000012196914

1.

CHECK ANTI-PINCH FUNCTION

1. Close the door.

2. Fully open the door window.

3. Place a piece of wood near fully closed position.

4. Close door glass completely with AUTO-UP.

5. Check the following conditions.

-

Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.

-

Check that glass does not rise not when operating the power window main switch while lowering.

CAUTION:

•

Perform initial setting when AUTO-UP operation or anti-pinch function does not operate nor-

mally.

•

Check that AUTO-UP operates before inspection when system initialization is performed.

•

Do not check with hands and other body parts because they may be pinched. Do not get

pinched.

>> END

Revision: November 2015

2016 JUKE

PWC-28

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

DTC/CIRCUIT DIAGNOSIS

POWER SUPPLY AND GROUND CIRCUIT

POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Diagnosis Procedure

INFOID:0000000012196915

1.

CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check voltage between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between BCM harness connector and power window main switch harness connector.

4. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace harness.

3.

CHECK POWER WINDOW MAIN SWITCH GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace harness.

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

(+)

(-)

Condition

Voltage (V)

Power window main switch

Connector

Terminal 

D35

10

Ground

Ignition switch

ON

9 – 16

D36

18

OFF

BCM

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

M69

68

D35

10

Existed

69

D36

18

BCM

Ground

Continuity

Connector

Terminal

M69

68

Not existed

69

Power window main switch 

Ground

Continuity 

Connector

Terminal

D35

1

Existed

Revision: November 2015

2016 JUKE

POWER SUPPLY AND GROUND CIRCUIT

PWC-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure

INFOID:0000000012196916

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect front power window switch (passenger side) connector.

3. Turn ignition switch ON.

4. Check voltage between front power window switch (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between BCM harness connector and front power window switch (passenger side) har-

ness connector.

4. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

 NO

>> Repair or replace harness.

REAR POWER WINDOW SWITCH
REAR POWER WINDOW SWITCH : Diagnosis Procedure

INFOID:0000000012196917

1.

CHECK REAR POWER WINDOW SWITCH POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect rear power window switch connector.

3. Turn ignition switch ON.

4. Check voltage between rear power window switch harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

(+)

(-)

Voltage (V)

Front power window switch (passenger side)

Connector

Terminal

D10

1

Ground

9 – 16

BCM

Front power window switch (passenger side)

Continuity

Connector

Terminal

 Connector

Terminal

M69

68

D10

1

Existed

BCM

Ground

Continuity

Connector

Terminal

M69

68

Not existed

(+)

(-)

Voltage (V)

Rear power window switch 

Connector

Terminal

LH

D63

1

Ground

9 – 16

RH

D43

Revision: November 2015

2016 JUKE

PWC-30

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

2.

CHECK REAR POWER WINDOW SWITCH POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between BCM harness connector and rear power window switch harness connector.

4. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace harness.

BCM

Rear power window switch

Continuity

Connector

Terminal

Connector

Terminal

M69

68

LH

D63

1

Existed

RH

D43

BCM

Ground

Continuity

Connector

Terminal

M69

68

Not existed

Revision: November 2015

2016 JUKE

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

PWC-31

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

Component Function Check

INFOID:0000000012196918

1.

 CHECK FUNCTION

Check front power window motor (passenger side) operation with front power window switch (passenger side)

and power window main switch (passenger side switch).
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-31, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196919

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) INPUT SIGNAL 

1. Turn ignition switch OFF.

2. Disconnect front power window switch (passenger side) connector.

3. Turn ignition switch ON.

4. Check voltage between front power window switch (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check continuity between front power window switch (passenger side) harness connector and power win-

dow main switch harness connector.

4. Check continuity between front power window switch (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-54, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

Check front power window switch (passenger side).

Refer to 

PWC-32, "Component Inspection"

.

(+)

(-)

Condition

Voltage (V)

Front power window switch (passenger side)

Connector

Terminal 

D10

2

Ground

Power window main 
switch
(passenger side 
switch)

NEUTRAL

0 – 1

UP

9 – 16

3

NEUTRAL

0 – 1

DOWN

9 – 16

Front power window switch (passenger side)

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

D10

2

D35

16

Existed

3

2

Front power window switch (passenger side)

Ground

Continuity

Connector

Terminal

D10

2

Not existed

3

Revision: November 2015

2016 JUKE

PWC-32

< DTC/CIRCUIT DIAGNOSIS >

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace front power window switch (passenger side). Refer to 

PWC-54, "Removal and Installa-

tion"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000012196920

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

1. Turn ignition switch OFF.

2. Disconnect front power window switch (passenger side) connector.

3. Check front power window switch (passenger side) terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front power window switch (passenger side). Refer to 

PWC-54, "Removal and Installa-

tion"

.

Front power window switch (passenger side)

Condition

Continuity

Terminal

1

5

UP

Existed

3

4

2

5

NEUTRAL

3

4

1

4

DOWN

2

5

Revision: November 2015

2016 JUKE

REAR POWER WINDOW SWITCH

PWC-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

REAR POWER WINDOW SWITCH 

Component Function Check

INFOID:0000000012196921

1.

 CHECK FUNCTION

Check rear power window motor (LH/RH) operation with rear power window switch (LH/RH) and pawer win-

dow main switch (rear LH/RH switch).
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-33, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196922

1.

CHECK REAR POWER WINDOW SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect rear power window switch connector.

3. Turn ignition switch ON.

4. Check voltage between rear power window switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK REAR POWER WINDOW SWITCH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check continuity between rear power window switch harness connector and power window main switch

harness connector.

4. Check continuity between rear power window switch harness connector and ground.

(+)

(-)

Condition

Voltage (V)

Rear power window switch

Connector

Terminal 

LH

D63

2

Ground

Power window main 
switch
(rear LH switch)

NEUTRAL

0 – 1

UP

9 – 16

3

NEUTRAL

0 – 1

DOWN

9 – 16

RH

D43

2

Power window main 
switch
(rear RH switch)

NEUTRAL

0 – 1

UP

9 – 16

3

NEUTRAL

0 – 1

DOWN

9 – 16

Rear power window switch

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

LH

D63

2

D35

9

Existed

3

8

RH

D43

2

7

3

6

Revision: November 2015

2016 JUKE

PWC-34

< DTC/CIRCUIT DIAGNOSIS >

REAR POWER WINDOW SWITCH

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-54, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Refer to 

PWC-34, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace rear power window switch. Refer to 

PWC-54, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000012196923

1.

CHECK REAR POWER WINDOW SWITCH

1. Turn ignition switch OFF.

2. Disconnect rear power window switch connector.

3. Check rear power window switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace rear power window switch. Refer to 

PWC-54, "Removal and Installation"

.

Rear power window switch

Ground

Continuity

Connector

Terminal

LH

D63

2

Not existed

3

RH

D43

2

3

Rear power window switch

Condition

Continuity

Terminal

1

5

UP

Existed

3

4

2

5

NEUTRAL

3

4

1

4

DOWN

2

5

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     532      533      534      535     ..