Nissan Juke (2016 year). Service Repair Manual - part 533

POWER WINDOW SYSTEM

PWC-19

< WIRING DIAGRAM >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

JRKWF4433GB

Revision: November 2015

2016 JUKE

PWC-20

< WIRING DIAGRAM >

POWER WINDOW SYSTEM

JRKWF4434GB

Revision: November 2015

2016 JUKE

POWER WINDOW SYSTEM

PWC-21

< WIRING DIAGRAM >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

JRKWF4435GB

Revision: November 2015

2016 JUKE

PWC-22

< WIRING DIAGRAM >

POWER WINDOW SYSTEM

JRKWF4436GB

Revision: November 2015

2016 JUKE

DIAGNOSIS AND REPAIR WORK FLOW

PWC-23

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

WorkFlow

INFOID:0000000012196906

DETAILED FLOW

1.

OBTAIN INFORMATION ABOUT SYMPTOM

Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-

tion occurred) as much as possible when the customer brings the vehicle in.

>> GO TO 2.

2.

REPRODUCE THE MALFUNCTION INFORMATION

Check the malfunction on the vehicle that the customer describes.

Inspect the relation of the symptoms and the condition when the symptoms occur.

>> GO TO 3.

3.

IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”

Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-

forming the diagnosis based on possible causes and symptoms.

>> GO TO 4.

4.

IDENTIFY THE MALFUNCTIONING PARTS WITH “DTC/CIRCUIT DIAGNOSIS”

Perform the diagnosis with “DTC/CIRCUIT DIAGNOSIS” of the applicable system.

>> GO TO 5.

5.

REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the specified malfunctioning parts.

>> GO TO 6.

6.

FINAL CHECK

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,

referring to the symptom inspection result in step 2.
Are the malfunctions corrected?

YES

>> INSPECTION END

NO

>> GO TO 3.

Revision: November 2015

2016 JUKE

PWC-24

< BASIC INSPECTION >

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL

Description

INFOID:0000000012196907

When the battery negative terminal is disconnected, the initialization is necessary for normal operation of

power window system. Refer to 

PWC-24, "Work Procedure"

.

CAUTION:

The following specified operations cannot be performed under the non-initialized condition.

• Auto-up operation

• Anti-pinch function

Work Procedure

INFOID:0000000012196908

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

PWC-26, "Description"

.

>> GO TO 2.

2.

CHECK ANTI-PINCH FUNCTION

Check anti-pinch function. Refer to 

PWC-27, "Description"

.

>> END

Revision: November 2015

2016 JUKE

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

PWC-25

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

Description

INFOID:0000000012196909

When the control unit replaced, the initialization in necessary for normal operation of power window system.

Refer to 

PWC-25, "Work Procedure"

.

CAUTION:

The following specified operations cannot be performed under the non-initialized condition.

• Auto-up operation

• Anti-pinch function

Work Procedure

INFOID:0000000012196910

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

PWC-26, "Description"

.

>> GO TO 2.

2.

CHECK ANTI-PINCH FUNCTION

Check anti-pinch function. Refer to 

PWC-27, "Description"

.

>> END

Revision: November 2015

2016 JUKE

PWC-26

< BASIC INSPECTION >

SYSTEM INITIALIZATION

SYSTEM INITIALIZATION

Description

INFOID:0000000012196911

If any of the following operations are performed, the initialization is necessary for normal operation of power

window system. Refer to 

PWC-26, "Work Procedure"

.

• Disconnection and connection of battery cable from negative terminal.

• When power window main switch replaced.

• Electric power supply to power window main switch or power window motor (driver side) is interrupted by

blown fuse or disconnection and connection of the negative terminal of battery, etc.

• Disconnection and connection of power window main switch harness connector.

• Removal of power window motor (driver side) from regulator assembly.

• Operation of regulator assembly as an independent unit.

• Removal and installation of glass.

• Removal and installation of door glass run.

CAUTION:

The following specified operations cannot be performed under the non-initialized condition.

• Auto-up operation

• Anti-pinch function

Work Procedure

INFOID:0000000012196912

1.

STEP 1

1. Close the door.

2. Turn ignition switch ON.

3. Operate power window switch to fully open the window. (This operation is unnecessary if the window is

already fully open)

4. Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed

position, keep pulling the switch for 2 seconds or more.

5. Check that AUTO-UP function operates normally.

>> GO TO 2.

2.

STEP 2

Check anti-pinch function. Refer to 

PWC-27, "Description"

.

>> END

Revision: November 2015

2016 JUKE