Nissan Juke (2016 year). Service Repair Manual - part 516

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     514      515      516      517     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 516

 

 

PCS-74

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

B26F1 IGNITION RELAY

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace harness.

BCM

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

M70

98

E17

68

Existed

Revision: November 2015

2016 JUKE

PCS

B26F2 IGNITION RELAY

PCS-75

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

B26F2 IGNITION RELAY

DTC Logic

INFOID:0000000012197212

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.

CVT models

-

Selector lever is in the P or N position

-

Do not depress brake pedal

M/T models

-

Do not depress clutch pedal

2. Check “Self-diagnosis result” with CONSULT. 
Is DTC detected?

YES

>> Go to 

PCS-75, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197213

1.

CHECK IPDM E/R SELF-DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Erase the DTC of IPDM E/R.

3. Turn ignition switch OFF.

4. Turn ignition switch ON and check the DTC again.
Is DTC detected?

YES

>> Repair or replace the malfunctioning part. Refer to 

PCS-24, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL

1. Turn ignition switch OFF.

2. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> GO TO 3.

3.

CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 1

1. Turn ignition switch OFF.

2. Disconnect BCM and IPDM E/R connectors.

3. Check continuity between IPDM E/R harness connector and ground.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B26F2

IGN RELAY ON

BCM transmits the ignition relay control signal 
(OFF: 12 V) or ignition switch ON signal (OFF) 
(CAN), but does not receives ignition switch 
ON signal (OFF) (CAN) from IPDM E/R.

• Harness or connectors

(Ignition relay circuit is short)

• BCM
• IPDM E/R

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E17

68

Ground

Ignition switch

OFF or ACC

12

Revision: November 2015

2016 JUKE

PCS-76

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

B26F2 IGNITION RELAY

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 2

1. Connect IPDM E/R connectors.

2. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Replace IPDM E/R.

IPDM E/R

Ground

Continuity

Connector

Terminal

E17

68

Not existed

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E17

68

Ground

Ignition switch

OFF or ACC

12

Revision: November 2015

2016 JUKE

PCS

B26F6 BCM

PCS-77

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

B26F6 BCM

DTC Logic

INFOID:0000000012197214

DTC DETECTION LOGIC

NOTE:

• If DTC B26F6 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B26F6 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 1 second or more.

CVT models

-

Selector lever is in the P or N position

-

Do not depress brake pedal

M/T models

-

Do not depress clutch pedal

2. Check “Self-diagnosis result” of BCM with CONSULT. 
Is DTC detected?

YES

>> Go to 

PCS-77, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197215

1.

INSPECTION START

1. Turn ignition switch ON.

2. Select “Self-diagnosis result” of BCM with CONSULT.

3. Touch “ERASE”.

4. Perform DTC Confirmation Procedure.

See 

BCS-62, "DTC Index"

.

Is DTC detected?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

NO

>> INSPECTION END

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B26F6

BCM

Ignition relay ON signal is not transmitted from IPDM E/
R when BCM turns ignition relay ON.

BCM

Revision: November 2015

2016 JUKE

PCS-78

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

PUSH-BUTTON IGNITION SWITCH

PUSH-BUTTON IGNITION SWITCH

Component Function Check

INFOID:0000000012197216

1.

CHECK FUNCTION

1. Select “PUSH SW” in “Data Monitor” mode with CONSULT.

2. Check the push-button ignition switch signal under the following conditions.

Is the indication normal?

YES

>> INSPECTION END.

NO

>> Go to  

PCS-78, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012197217

1.

CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 1

1. Turn ignition switch OFF.

2. Disconnect push-button ignition switch connector and IPDM E/R connector.

3. Check voltage between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 1

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and push-button ignition switch harness connector.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 2

Check voltage between IPDM E/R harness connector and ground.

Test item

Condition

Status

PUSH SW

Push-button ignition switch is pressed

ON

Push-button ignition switch is not pressed

OFF

(+)

(–)

Voltage (V)

(Approx.)

Push-button ignition switch

Connector

Terminal

M101

8

Ground

12

BCM

Push-button ignition switch

Continuity

Connector

Terminal

Connector

Terminal

M70

76

M101

8

Existed

BCM

Ground

Continuity

Connector

Terminal

M70

76

Not existed

Revision: November 2015

2016 JUKE

PCS

PUSH-BUTTON IGNITION SWITCH

PCS-79

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 2

1. Disconnect BCM connector.

2. Check continuity between IPDM E/R harness connector and push-button ignition switch harness connec-

tor.

3. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace harness.

5.

CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT 

Check continuity between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK PUSH-BUTTON IGNITION SWITCH

Refer to 

PCS-79, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace push-button ignition switch.

7.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000012197218

1.

CHECK PUSH-BUTTON IGNITION SWITCH

1. Turn ignition switch OFF.

2. Disconnect push-button ignition switch connector.

3. Check continuity between push-button ignition switch terminals.

(+)

(–)

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E17

66

Ground

12

IPDM E/R

Push-button ignition switch

Continuity

Connector

Terminal

Connector

Terminal

E17

66

M101

8

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E17

66

Not existed

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M101

4

Existed

Revision: November 2015

2016 JUKE

PCS-80

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

PUSH-BUTTON IGNITION SWITCH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace push-button ignition switch.

Push-button ignition switch

Condition

Continuity

Terminal

4

8

Pressed

Existed

Not pressed

Not existed

Revision: November 2015

2016 JUKE

PCS

PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR

PCS-81

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR

Description

INFOID:0000000012197219

Push-button ignition switch changes the power supply position.

BCM maintains the power supply position status.

BCM changes the power supply position with the operation of the push-button ignition switch.

Component Function Check

INFOID:0000000012197220

1.

CHECK FUNCTION

Check push-button ignition switch (“PUSH SWITCH INDICATOR”) in Active Test Mode with CONSULT.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PCS-81, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012197221

1.

CHECK PUSH-BUTTON IGNITION SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect push-button ignition switch connector.

3. Check voltage between push-button ignition switch harness connector and ground.

Is the inspection normal?

YES

>> GO TO 2.

NO-1 >> Check 10 A fuse [No.13, located in fuse block (J/B)].

NO-2 >> Check harness for open or short between push-button ignition switch and fuse.

2.

CHECK BCM INPUT

1. Connect push-button ignition switch connector.

2. Disconnect BCM connector.

3. Check voltage between BCM connector and ground.

Is the inspection normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> GO TO 3.

3.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT

1. Disconnect push-button ignition switch connector.

2. Check continuity between BCM harness connector and push-button ignition switch harness connector.

Test item

Description

PUSH SWITCH INDICATOR

ON

Position indicator

 Illuminates

OFF

Does not illuminate

(+)

(–)

Voltage (V)

(Approx.)

Push-button ignition switch

Connector

Terminal

M101

3

Ground

Battery voltage

(+)

(–)

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M70

91

Ground

Battery voltage

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     514      515      516      517     ..