Nissan Juke (2016 year). Service Repair Manual - part 515

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     513      514      515      516     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 515

 

 

PCS-66

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

B2615 BLOWER RELAY CIRCUIT

B2615 BLOWER RELAY CIRCUIT

DTC Logic

INFOID:0000000012197200

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 1 second or more.

-

Selector lever is in the P position

-

Do not depress brake pedal

2. Check “Self-diagnosis result” of BCM with CONSULT.
Is DTC detected?

YES

>> Go to 

PCS-66, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197201

1.

CHECK BLOWER RELAY POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect blower relay.

3. Check voltage between blower relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK BLOWER RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between blower relay harness connector and BCM harness connector.

4. Check continuity between blower relay harness connector and ground.

Is the inspection result normal?

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B2615

BCM

BCM detects a difference of signal for 1 second or 
more between the following items.
• Blower relay ON/OFF request 
• Blower relay feedback

• Harness or connectors 

(Blower relay circuit is open or 
shorted)

• BCM
• Blower relay

(+)

(–)

Condition

Voltage (V)

(Approx.)

Blower relay

Terminal

1

Ground

Ignition switch

OFF or ACC

0

ON

Battery voltage

Blower relay

BCM

Continuity

Terminal

Connector

Terminal

1

M70

106

Existed

Blower relay

Ground

Continuity

Terminal

1

Not existed

Revision: November 2015

2016 JUKE

PCS

B2615 BLOWER RELAY CIRCUIT

PCS-67

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

YES

>> GO TO 6.

NO

>> Repair or replace harness.

3.

CHECK BLOWER RELAY GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check continuity between blower relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair blower relay ground circuit.

4.

CHECK BLOWER RELAY POWER SUPPLY CIRCUIT-2

1. Turn ignition switch ON.

2. Check voltage between blower relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Check continuity open or short between blower relay and battery.

5.

CHECK BLOWER RELAY

Refer to 

PCS-67, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace blower relay.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000012197202

1.

CHECK BLOWER RELAY

1. Turn ignition switch OFF.

2. Remove blower relay.

3. Check the continuity between blower relay terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace blower relay

Blower relay

Ground

Continuity

Terminal

2

Existed

(+)

(–)

Voltage (V)

(Approx.)

Blower relay

Terminal

5

Ground

Battery voltage

Terminals

Condition

Continuity

3 and 5

12 V direct current supply between terminals 1 and 2

Existed

No current supply

Not existed

PBIB0098E

Revision: November 2015

2016 JUKE

PCS-68

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

B2616 IGNITION RELAY CIRCUIT

B2616 IGNITION RELAY CIRCUIT

DTC Logic

INFOID:0000000012197203

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 1 second or more.

-

Selector lever is in the P position

-

Do not depress brake pedal

2. Check “Self-diagnosis result” with CONSULT.
Is DTC detected?

YES

>> Go to 

PCS-68, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197204

1.

CHECK IGNITION RELAY POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect ignition relay.

3. Check voltage between ignition relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK IGNITION RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between ignition relay harness connector and BCM harness connector.

4. Check continuity between ignition relay harness connector and ground.

Is the inspection result normal?

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B2616

BCM

An immediate operation of ignition relay is request-
ed by BCM, but there is no response for more than 
1 second

• Harness or connectors 

(Ignition relay circuit is open or 
shorted)

• BCM
• Ignition relay

(+)

(–)

Condition

Voltage (V)

(Approx.)

Ignition relay

Terminal

2

Ground

Ignition switch

OFF or ACC

0

ON

Battery voltage

Ignition relay

BCM

Continuity

Terminal

Connector

Terminal

2

M70

99

Existed

Ignition relay

Ground

Continuity

Terminal

2

Not existed

Revision: November 2015

2016 JUKE

PCS

B2616 IGNITION RELAY CIRCUIT

PCS-69

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK IGNITION RELAY GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check continuity between ignition relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair ignition relay ground circuit.

4.

CHECK IGNITION RELAY POWER SUPPLY CIRCUIT-2

1. Turn ignition switch ON.

2. Check voltage between ignition relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Check continuity open or short between ignition relay and battery.

5.

CHECK IGNITION RELAY

Refer to 

PCS-69, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace ignition relay.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000012197205

1.

CHECK IGNITION RELAY

1. Turn ignition switch OFF.

2. Remove ignition relay.

3. Check the continuity between ignition relay terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace Ignition relay

Ignition relay

Ground

Continuity

Terminal

1

Existed

(+)

(–)

Voltage (V)

(Approx.)

Ignition relay

Terminal

5

Ground

Battery voltage

Terminals

Condition

Continuity

3 and 5

12 V direct current supply between terminals 1 and 2

Existed

No current supply

Not existed

PBIB0098E

Revision: November 2015

2016 JUKE

PCS-70

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

B2618 BCM

B2618 BCM

DTC Logic

INFOID:0000000012197206

DTC DETECTION LOGIC

NOTE:

• If DTC B2618 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B2618 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 1 second or more.

CVT models

-

Selector lever is in the P or N position

-

Do not depress brake pedal

M/T models

-

Do not depress clutch pedal

2. Check “Self-diagnosis result” of BCM with CONSULT. 
Is DTC detected?

YES

>> Go to 

PCS-70, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197207

1.

INSPECTION START

1. Turn ignition switch ON.

2. Select “Self-diagnosis result” of BCM with CONSULT.

3. Touch “ERASE”.

4. Perform DTC Confirmation Procedure.

See 

PCS-70, "DTC Logic"

.

Is the 1st trip DTC B2618 displayed again?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

NO

>> INSPECTION END

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B2618

BCM

An immediate operation of ignition relay (IPDM E/R) is re-
quested by BCM, but there is no response for more than 
1 second

BCM

Revision: November 2015

2016 JUKE

PCS

B261A PUSH-BUTTON IGNITION SWITCH

PCS-71

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

B261A PUSH-BUTTON IGNITION SWITCH

DTC Logic

INFOID:0000000012197208

DTC DETECTION LOGIC

NOTE:

• If DTC B261A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B261A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press the push-button ignition switch under the following conditions, and wait for 1 second or more.

CVT models

-

Selector lever is in the P or N position

-

Do not depress brake pedal

M/T models

-

Do not depress clutch pedal

2. Check “Self-diagnosis result” of BCM with CONSULT. 
Is DTC detected?

YES

>> Go to 

PCS-71, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197209

1.

CHECK IGNITION SWITCH OUTPUT SIGNAL (PUSH-BUTTON IGNITION SWITCH)

1. Disconnect push-button ignition switch connector and IPDM E/R connector.

2. Check voltage between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (BCM)

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and push-button ignition switch harness connector.

3. Check continuity between push-button ignition switch harness connector and ground.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B261A

PUSH-BTN IGN SW

 BCM detects a difference of signal for 1 second or 
more between the following items. 
• Push-button ignition switch signal
• Push-button ignition switch status signal (CAN)

• Harness or connectors

(Push-button ignition switch circuit 
is open or shorted.)

• BCM
• IPDM  E/R

(+)

(–)

Voltage (V)

(Approx.)

Push-button ignition switch

Connector

Terminal

M101

8

Ground

12

BCM

Push-button ignition switch

Continuity

Connector

Terminal

Connector

Terminal

M70

76

M101

8

Existed

Revision: November 2015

2016 JUKE

PCS-72

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

B261A PUSH-BUTTON IGNITION SWITCH

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R)

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> GO TO 4.

4.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R)

1. Disconnect BCM connector.

2. Check continuity between IPDM E/R harness connector and push-button ignition switch harness connec-

tor.

3. Check continuity between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M101

8

Not existed

(+)

(–)

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E17

66

Ground

12

IPDM E/R

Push-button ignition switch

Continuity

Connector

Terminal

Connector

Terminal

E17

66

M101

8

Existed

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M101

8

Not existed

Revision: November 2015

2016 JUKE

PCS

B26F1 IGNITION RELAY

PCS-73

< DTC/CIRCUIT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

B26F1 IGNITION RELAY

DTC Logic

INFOID:0000000012197210

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.

CVT models

-

Selector lever is in the P or N position

-

Do not depress brake pedal

M/T models

-

Do not depress clutch pedal

2. Check “Self-diagnosis result” with CONSULT. 
Is DTC detected?

YES

>> Go to 

PCS-73, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197211

1.

CHECK IPDM E/R SELF-DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Erase the DTC of IPDM E/R.

3. Turn ignition switch OFF.

4. Turn ignition switch ON and check the DTC again.
Is DTC detected?

YES

>> Repair or replace the malfunctioning part. Refer to 

PCS-24, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

3.

CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM and IPDM connectors.

3. Check continuity between BCM harness connector and IPDM E/R harness connector.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B26F1

IGN RELAY OFF

BCM transmits the ignition relay control signal 
(ON: 0 V) or ignition switch ON signal (ON) 
(CAN), but does not receives ignition switch 
ON signal (ON) (CAN) from IPDM E/R.

• Harness or connectors

(Ignition relay circuit is open)

• BCM
• IPDM E/R

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M70

98

Ground

Ignition switch

ON

0

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     513      514      515      516     ..