Nissan Juke (2016 year). Service Repair Manual - part 505

MWI-64

< REMOVAL AND INSTALLATION >

COMBINATION METER

REMOVAL AND INSTALLATION

COMBINATION METER

Exploded View

INFOID:0000000012201350

REMOVAL

Refer to 

IP-12, "Exploded View"

.

DISASSEMBLY

Removal and Installation

INFOID:0000000012201351

REMOVAL

1. Remove cluster lid A. Refer to 

IP-13, "Removal and Installation"

.

2. Remove the mounting screws of the combination meter.
3. Pull the combination meter straight to disengage resin clips.

(The figure shows the clip positions on the back of the combina-

tion meter.)

CAUTION:

Never damage the front cover.

1.

Front cover

2.

Unified meter control unit

JSNIA3219ZZ

JSNIA3208ZZ

Revision: November 2015

2016 JUKE

MWI

COMBINATION METER

MWI-65

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

4. Turn the lower part of the combination meter in the direction of

the arrow to remove the combination meter from the instrument

panel assembly.

CAUTION:

Never damage the front cover.

5. Remove connector to remove the combination meter.

CAUTION:

Never damage the front cover.

INSTALLATION

Install in the reverse order of removal.

Disassembly and Assembly

INFOID:0000000012201352

DISASSEMBLY

1. Disengage the pawls (2 on the sides, 3 on the lower part) of the combination meter. 
2. Insert the removal tool into the clearance (in the order of A, B)

between the front cover and the meter control unit. Remove 4

pawls on the upper side of the front cover by turning the tool

while increasing the clearance. 

CAUTION:

Wrap the removal tools with protective tape to prevent

scratches. 

3. Pull the front cover straight to remove it from the meter control unit assembly.

CAUTION:

Never damage the front cover.

Never touch the pointer and the crystalline liquid.

ASSEMBLY

Install the front cover straight to the meter control unit assembly and engage all the pawl.

CAUTION:

Never damage the front cover.

JSNIA3546ZZ

JSNIA3210ZZ

Revision: November 2015

2016 JUKE

PB-1

BRAKES

C

D

E

G

H

I

J

K

L

M

SECTION 

PB

A

B

PB

N

O

P

CONTENTS

PARKING BRAKE SYSTEM

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Precautions for Removing Battery Terminal  .............

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Commercial Service Tool  ..........................................

3

PERIODIC MAINTENANCE ..........................

4

PARKING BRAKE SYSTEM ...............................

4

Inspection and Adjustment ........................................

4

PARKING BRAKE SHOE  ...................................

5

Adjustment ................................................................

5

REMOVAL AND INSTALLATION ................

6

PARKING BRAKE CONTROL ...........................

6

Exploded View ..........................................................

6

Removal and Installation  ..........................................

7

Adjustment ................................................................

8

PARKING BRAKE SHOE  ..................................

9

Exploded View ..........................................................

9

Removal and Installation  ..........................................

9

Inspection and Adjustment  ......................................

11

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

13

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

13

Parking Drum Brake  ................................................

13

Parking Brake Control  .............................................

13

Revision: November 2015

2016 JUKE

PB-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precautions for Removing Battery Terminal

INFOID:0000000012200162

•  When removing the 12V battery terminal, turn OFF the ignition

switch and wait at least 30 seconds.

NOTE:

ECU may be active for several tens of seconds after the ignition

switch is turned OFF. If the battery terminal is removed before ECU

stops, then a DTC detection error or ECU data corruption may

occur.

•  For vehicles with the 2-batteries, be sure to connect the main bat-

tery and the sub battery before turning ON the ignition switch.

NOTE:

If the ignition switch is turned ON with any one of the terminals of

main battery and sub battery disconnected, then DTC may be

detected.

•  After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

NOTE:

The removal of 12V battery may cause a DTC detection error.

SEF289H

Revision: November 2015

2016 JUKE

PREPARATION

PB-3

< PREPARATION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

PREPARATION

PREPARATION

Commercial Service Tool

INFOID:0000000012200163

Tool name

Description

Power tool

Loosening bolts and nuts

PBIC0190E

Revision: November 2015

2016 JUKE

PB-4

< PERIODIC MAINTENANCE >

PARKING BRAKE SYSTEM

PERIODIC MAINTENANCE

PARKING BRAKE SYSTEM

Inspection and Adjustment

INFOID:0000000012200164

INSPECTION

Lever Stroke

1. Operate the parking brake lever with a force of 196 N (20 kg, 44 lb). Check that the lever stroke is within

the specified number of notches. (Check it by listening to the clicks of the ratchet.)

2. When brake warning lamp turns ON, check that the lever stroke is within the specified number of notches.

(Check it by listening to the clicks of the ratchet.)

Inspect Components

• Check each component for installation condition such as looseness.

• Check the parking brake lever assembly for bend, damage and cracks. Replace if necessary.

• Check the cables and equalizer for wear, damage and cracks. Replace if necessary.

• Check the parking brake switch, and replace it if necessary. Refer to 

BRC-116, "Component Inspection"

.

ADJUSTMENT

1. Remove rear tires with power tool.
2. Fix the disc rotor using wheel nut.
3. Remove the console mask. Refer to 

IP-24, "Removal and Installation"

.

4. Remove the adjusting hole plug from the disc rotor. Turn the

adjuster (1) in the direction (A) as shown in the figure using a

suitable tool until the disc rotor is locked.

5. Turn back the adjuster 7 notches from the locked position.
6. Rotate the disc rotor to check that there is no drag. Install the

adjuster hole plug. Refer to 

PB-11, "Inspection and Adjustment"

.

7. Adjust the cable with the following procedure.
a. Operate and maintain the parking brake lever with a force of 400 N (41 kg, 90 lb) for 15 minutes or more.
b. Adjust the parking brake lever stroke by turning the adjusting nut

(1) with a socket wrench.

CAUTION:

Make sure to securely depress the brake pedal.

c.

Operate the parking brake lever with a force of 196 N (20 kg,

44lb). Check that the lever stroke is within the specified number

of notches. (Check it by listening to the clicks of the ratchet.)

d. Rotate the disc rotor to check that there is no drag. Refer to 

PB-

11, "Inspection and Adjustment"

.

Number of notches

: Refer to 

PB-13, "Parking Brake Control"

.

Number of notches

: Refer to 

PB-13, "Parking Brake Control"

.

JPFIB0088ZZ

Number of notches

: Refer to 

PB-13, "Parking 

Brake Control"

.

JPFIB0131ZZ

Revision: November 2015

2016 JUKE

PARKING BRAKE SHOE

PB-5

< PERIODIC MAINTENANCE >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

PARKING BRAKE SHOE

Adjustment

INFOID:0000000012200165

1. Adjust parking brake lever stroke. Refer to 

PB-4, "Inspection and Adjustment"

.

2. Perform parking brake break-in (drag on) operation by driving vehicle under the following conditions:

• Drive forward

• Vehicle speed: Approx. 43 km/h (27 MPH) set (constant and forward)

• Parking brake operating force: 125 N (12.8 kg, 28.1 lb) set contact

• Time: Approx. 8 sec.

CAUTION:

To prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after

every break-in operation.

3. After the break-in procedure, check parking brake lever stroke of parking brake.

CAUTION:

If it is out of the specification, adjust again. Refer to 

PB-4, "Inspection and Adjustment"

.

Revision: November 2015

2016 JUKE

PB-6

< REMOVAL AND INSTALLATION >

PARKING BRAKE CONTROL

REMOVAL AND INSTALLATION

PARKING BRAKE CONTROL

Exploded View

INFOID:0000000012200166

2WD

AWD

1.

Parking brake lever assembly

2.

Adjusting nut

3.

Parking brake switch

4.

Front cable

5.

Rear cable (LH)

6.

Rear cable (RH)

: Apply multi-purpose grease.

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

: Always replace after every disassembly.

JSFIA0603GB

Revision: November 2015

2016 JUKE