Nissan Juke (2016 year). Service Repair Manual - part 504

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     502      503      504      505     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 504

 

 

MWI-56

< DTC/CIRCUIT DIAGNOSIS >

FUEL LEVEL SENSOR SIGNAL CIRCUIT

4. Check continuity between combination meter harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK FUEL LEVEL SENSOR GROUND CIRCUIT

1. Check continuity between fuel level sensor unit and fuel pump harness connector terminal and combina-

tion meter harness connector terminal.

2. Check continuity between combination meter harness connector terminal and ground.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

NO

>> Repair harness or connector.

Component Inspection

INFOID:0000000012201339

2WD MODELS

1.

REMOVE FUEL LEVEL SENSOR UNIT AND FUEL PUMP

Remove the fuel level sensor unit and fuel pump. Refer to 

FL-7, "2WD : Removal and Installation"

.

>> GO TO 2.

2.

CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP

Check the resistance between fuel level sensor unit and fuel pump.

*: When float rod is contact with stopper.

Is inspection result OK?

YES

>> INSPECTION END

NO

>> Replace fuel level sensor unit and fuel pump. Refer to 

FL-7, "2WD : Removal and Installation"

.

AWD MODELS

Combination meter

Fuel level sensor unit and fuel pump

Continuity

Connector

Terminal

Connector

Terminal

M34

6

B46

2

Existed

Combination meter

Ground

Continuity

Connector

Terminal

M34

6

Not existed

Fuel level sensor unit and fuel pump

Combination meter

Continuity

Connector

Terminal

Connector

Terminal

B46

5

M34

24

Existed

Combination meter

Ground

Continuity

Connector

Terminal

M34

24

Not existed

Terminals

Condition

Resistance (

)

(Approx.)

Height [mm (in)]

Fuel level sensor unit 

and fuel pump

2

5

Full

*

 (A)

51

142.8 (5.62)

Empty

*

 (B)

283

14.3 (0.563)

JSNIA3599ZZ

Revision: November 2015

2016 JUKE

MWI

FUEL LEVEL SENSOR SIGNAL CIRCUIT

MWI-57

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

1.

REMOVE FUEL LEVEL SENSOR UNIT AND FUEL PUMP (MAIN)

Remove the fuel level sensor unit and fuel pump (main). Refer to 

FL-11, "AWD : Removal and Installation"

.

>> GO TO 2.

2.

CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (MAIN)

Check the resistance between fuel level sensor unit and fuel pump.

*: When float rod is contact with stopper.

Is inspection result OK?

YES

>> GO TO 3.

NO

>> Replace fuel level sensor unit and fuel pump (main). Refer to 

FL-11, "AWD : Removal and Instal-

lation"

.

3.

REMOVE FUEL LEVEL SENSOR UNIT (SUB)

Remove the fuel level sensor unit (sub). Refer to 

FL-11, "AWD : Removal and Installation"

.

>> GO TO 4.

4.

CHECK FUEL LEVEL SENSOR UNIT (SUB)

Check the resistance between fuel level sensor unit (sub).

*: When float rod is contact with stopper.

Is inspection result OK?

YES

>> INSPECTION END

NO

>> Replace fuel level sensor unit (sub). Refer to 

FL-11, "AWD : Removal and Installation"

.

Terminals

Condition

Resistance (

)

(Approx.)

Height [mm (in)]

Fuel level sensor unit 
and fuel pump (main)

5

2

Full

*

 (A)

25.5

147.4 (5.8)

Empty

*

 (B)

99.5

13.3 (0.524)

6

7

0

JSNIA3600ZZ

Terminals

Condition

Resistance (

)

(Approx.)

Height [mm (in)]

Fuel level sensor unit 

(sub)

7

6

Full

*

 (A)

25.5

157.4 (6.2)

Empty

*

 (B)

183.5

7.1 (0.28)

JSNIA3333ZZ

Revision: November 2015

2016 JUKE

MWI-58

< DTC/CIRCUIT DIAGNOSIS >

A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT

A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT

Diagnosis Procedure

INFOID:0000000012201340

1.

CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL

1. Turn ignition switch ON.

2. Check voltage between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect combination meter connector and A/C auto amp. connector.

3. Check continuity between combination meter harness connector and A/C auto amp. harness connector.

4. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

Terminals

Voltage

(Approx.)

(+)

(

)

Combination meter

Ground

Connector

Terminal

M34

31

5 V

Combination meter

A/C auto amp.

Continuity

Connector

Terminal

Connector

terminal

M34

31

M50

9

Existed

Combination meter

Ground

Continuity

Connector

Terminal

M34

31

Not existed

Revision: November 2015

2016 JUKE

MWI

THE FUEL GAUGE INDICATOR DOES NOT OPERATE

MWI-59

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SYMPTOM DIAGNOSIS

THE FUEL GAUGE INDICATOR DOES NOT OPERATE

Description

INFOID:0000000012201341

Fuel gauge will not indicate from a certain position.

Diagnosis Procedure

INFOID:0000000012201342

1.

CONDUCTING THE COMBINATION METER SELF-DIAGNOSIS MODE

Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally.

Refer to 

MWI-21, "On Board Diagnosis Function"

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

2.

CHECK FLOAT INTERFERENCE

Check that the float arm interferes with or binds to other components in the fuel tank.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning part.

3.

CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT

Check the fuel level sensor signal circuit. Refer to 

MWI-54, "Component Function Check"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Revision: November 2015

2016 JUKE

MWI-60

< SYMPTOM DIAGNOSIS >

THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON

THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON

Description

INFOID:0000000012201343

The oil pressure warning lamp stays off when the ignition switch is turned ON.

Diagnosis Procedure

INFOID:0000000012201344

1.

CHECK COMBINATION METER INPUT SIGNAL

1. Start the engine.

2. Select “Data Monitor” in “METER/M&A” to check that the oil pressure warning lamp state is consistent

with the “OIL W/L” monitor value.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

MWI

THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF

MWI-61

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF

Description

INFOID:0000000012201345

The oil pressure warning lamp remains illuminated while the engine is running (normal oil pressure).

Diagnosis Procedure

INFOID:0000000012201346

1.

CHECK COMBINATION METER INPUT SIGNAL

1. Start the engine.

2. Select “Data Monitor” in “METER/M&A” to check that the oil pressure warning lamp state is consistent

with the “OIL W/L” monitor value.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

MWI-62

< SYMPTOM DIAGNOSIS >

THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT

THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT

Description

INFOID:0000000012201347

• The displayed ambient air temperature is higher than the actual temperature.

• The displayed ambient air temperature is lower than the actual temperature.

Diagnosis Procedure

INFOID:0000000012201348

NOTE:

Check that the symptom is not applicable to the normal operating condition before starting diagnosis. Refer to

MWI-63, "INFORMATION DISPLAY : Description"

.

1.

CHECK AMBIENT SENSOR SIGNAL CIRCUIT

Check the ambient sensor signal circuit. Refer to 

HAC-58, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT

Check the A/C auto amp. connection recognition signal circuit. Refer to 

MWI-58, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK AMBIENT SENSOR

Perform the part check for the ambient sensor. Refer to 

HAC-59, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

NO

>> Replace ambient sensor. Refer to 

HAC-94, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

MWI

NORMAL OPERATING CONDITION

MWI-63

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

NORMAL OPERATING CONDITION

INFORMATION DISPLAY
INFORMATION DISPLAY : Description

INFOID:0000000012201349

AMBIENT TEMPERATURE

The displayed ambient temperature on the information display may differ from the actual temperature because

it is a corrected value calculated from the ambient sensor signal by the combination meter. Refer to  

MWI-16,

"INFORMATION DISPLAY : System Description"

 for details on the correction process.

DISTANCE TO EMPTY

The calculated distance to empty may differ from the actual distance to empty if the refueling amount is
approximately 15   (4 US gal, 3-1/4 Imp gal) or less. This is because the refuel control (moves the fuel gauge

needle quicker than normal judging that the driver is refueling the vehicle) is not performing.

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     502      503      504      505     ..