Nissan Juke (2016 year). Service Repair Manual - part 361

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     359      360      361      362     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 361

 

 

EXL-110

< REMOVAL AND INSTALLATION >

[XENON TYPE]

REAR COMBINATION LAMP

• Never touch bulb by hand while it is lit or right after being turned off.

• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

TAIL LAMP (LED)

CAUTION:

Replacement of a single part is not possible due to the adoption of LED. For replacement, replace rear

combination lamp as a set. Refer to 

EXL-109, "Removal and Installation"

.

STOP/TAIL LAMP BULB (REAR SIDE MARKER LAMP)

1. Remove rear combination lamp assembly. Refer to 

EXL-109, "Removal and Installation"

.

2. Rotate stop/tail lamp bulb socket counterclockwise, and then remove stop/tail lamp bulb socket.
3. Remove stop/tail lamp bulb from stop/tail lamp bulb socket.

REAR TURN SIGNAL LAMP BULB

1. Remove rear combination lamp assembly. Refer to 

EXL-109, "Removal and Installation"

.

2. Rotate rear turn signal lamp bulb socket counterclockwise, and then remove rear turn signal lamp bulb

socket.

3. Remove rear turn signal lamp bulb from rear turn signal lamp bulb socket.

BACK-UP LAMP BULB

1. Remove rear combination lamp assembly. Refer to 

EXL-109, "Removal and Installation"

.

2. Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3. Remove back-up lamp bulb from back-up lamp bulb socket.

Revision: November 2015

2016 JUKE

HIGH-MOUNTED STOP LAMP

EXL-111

< REMOVAL AND INSTALLATION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

HIGH-MOUNTED STOP LAMP

Exploded View

INFOID:0000000012201702

EXCEPT FOR NISMO AND NISMO RS

NISMO AND NISMO RS

Removal and Installation

INFOID:0000000012201703

CAUTION:

Disconnect the battery negative terminal or remove power circuit fuse when performing the operation

for preventing electric leakage. Refer to 

EXL-7, "Precautions for Removing Battery Terminal"

.

REMOVAL

Except for NISMO and NISMO RS

1. Remove blind seal from back door inside.

CAUTION:

1.

High-mounted stop lamp

2.

Seal packing

: N·m (kg-m, in-lb)

JMLIA1220GB

1.

Rear spoiler

2.

High-mounted stop lamp

3.

High-mounted stop lamp cover

JMLIA3757ZZ

Revision: November 2015

2016 JUKE

EXL-112

< REMOVAL AND INSTALLATION >

[XENON TYPE]

HIGH-MOUNTED STOP LAMP

Never damage the blind seal, so that it can be reused.

2. Remove high-mounted stop lamp mounting nuts and connector.
3. Pull high-mounted stop lamp toward vehicle upside, and then remove high-mounted stop lamp.

NISMO and NISMO RS

1. Remove rear spoiler. Refer to 

EXT-49, "Removal and Installation"

.

2. Remove high-mounted stop lamp cover mounting bolts, and then remove high-mounted stop lamp cover.
3. Remove high-mounted stop lamp harness connector from rear spoiler.
4. Pull out high-mounted stop lamp, and then remove high-mounted stop lamp.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

Seal packing cannot be reused.

Revision: November 2015

2016 JUKE

LICENSE PLATE LAMP

EXL-113

< REMOVAL AND INSTALLATION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LICENSE PLATE LAMP

Exploded View

INFOID:0000000012201704

Removal and Installation

INFOID:0000000012201705

CAUTION:

Disconnect the battery negative terminal or remove power circuit fuse when performing the operation

for preventing electric leakage. Refer to 

EXL-7, "Precautions for Removing Battery Terminal"

.

REMOVAL

1. While pressing the license plate lamp to direction right side, pull

it to direction outside and then remove it.

2. Disconnect license plate lamp connector.

INSTALLATION

Install in the reverse order of removal.

Replacement

INFOID:0000000012201706

CAUTION:

• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-

tion for preventing electric leakage. Refer to 

EXL-7, "Precautions for Removing Battery Terminal"

.

• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.

• Never touch bulb by hand while it is lit or right after being turned off.

• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

LICENSE PLATE LAMP BULB

1. Remove license plate lamp. Refer to 

EXL-113, "Removal and Installation"

.

2. Rotate the bulb socket counterclockwise and unlock it.

1.

License plate lamp housing assembly

2.

Bulb

3.

License plate lamp bulb socket

: Pawl

JMLIA1219ZZ

JPLIA0364ZZ

Revision: November 2015

2016 JUKE

EXL-114

< REMOVAL AND INSTALLATION >

[XENON TYPE]

LICENSE PLATE LAMP

3. Remove the bulb from the socket.

Revision: November 2015

2016 JUKE

REAR FOG LAMP

EXL-115

< REMOVAL AND INSTALLATION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

REAR FOG LAMP

Exploded View

INFOID:0000000012201707

REMOVAL

Removal and Installation

INFOID:0000000012201708

REMOVAL

1. Remove rear bumper fascia lower. Refer to 

EXT-23, "Removal and Installation"

.

2. Remove rear fog lamp housing mounting nuts.
3. Remove rear fog lamp housing from the rear bumper fascia lower.
4. Remove rear fog lamp housing bracket from rear bumper fascia lower.

INSTALLATION

Installation is the reverse order of removal.

1.

Rear fog lamp housing

2.

Rear bumper fascia lower

3.

Rear fog lamp housing bracket

N·m (kg-m, in-lb)

: Vehicle front

JMLIA3677GB

Revision: November 2015

2016 JUKE

EXL-116

< REMOVAL AND INSTALLATION >

[XENON TYPE]

REAR REFLEX REFLECTOR

REAR REFLEX REFLECTOR

Exploded View

INFOID:0000000012201709

EXCEPT FOR NISMO AND NISMO RS

NISMO AND NISMO RS

Removal and Installation

INFOID:0000000012201710

REMOVAL

Except for NISMO and NISMO RS

1. Remove rear bumper fascia lower. Refer to 

EXT-23, "Removal and Installation"

.

1.

Rear bumper fascia lower

2.

Rear reflex reflector LH

3.

Rear reflex reflector RH

: Pawl

: N·m (kg-m, in-lb)

JMLIA5406GB

1.

Rear bumper fascia lower

2.

Rear reflex reflector RH

3.

Rear reflex reflector LH

: Metal clip

: Vehicle front

JMLIA3679ZZ

Revision: November 2015

2016 JUKE

REAR REFLEX REFLECTOR

EXL-117

< REMOVAL AND INSTALLATION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

2. Remove rear reflex reflector fixing screw.
3. Disengage rear reflex reflector fixing pawls, and then remove rear reflex reflector.

NISMO and NISMO RS

1. Remove rear bumper fascia lower. Refer to 

EXT-23, "Removal and Installation"

.

2. Disengage rear reflex reflector fixing metal clip, and then

remove rear reflex reflector according to numerical order 1

3

indicated by arrows as shown in the figure.

INSTALLATION

Install in the reverse order of removal.

JMLIA3680ZZ

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     359      360      361      362     ..