Nissan Juke (2016 year). Service Repair Manual - part 290

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     288      289      290      291     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 290

 

 

P2096, P2097 A/F SENSOR 1

EC-1135

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

NO

>> GO TO 14.

14.

CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE

Clear the mixture ratio self-learning value. Refer to 

EC-762, "Description"

.

Do you have CONSULT?

YES

>> GO TO 15.

NO

>> INSPECTION END

15.

CONFIRM A/F ADJUSTMENT DATA

With CONSULT

1. Turn ignition switch ON.

2. Select “A/F ADJ-B1” in “DATA MONITOR” mode with CONSULT.

3. Make sure that “0.000” is displayed on CONSULT screen.

>> INSPECTION END

Revision: November 2015

2016 JUKE

EC-1136

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2100, P2103 THROTTLE CONTROL MOTOR RELAY

P2100, P2103 THROTTLE CONTROL MOTOR RELAY

DTC Logic

INFOID:0000000012198659

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V.

Witch DTC is detected?

P2100 >> GO TO 2.

P2103 >> GO TO 3.

2.

PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P2100

1. Turn ignition switch ON and wait at least 2 seconds.

2. Start engine and let it idle for 5 seconds.

3. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-1136, "Diagnosis Procedure"

.

NO

>> INSPECTION END

3.

PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P2103

1. Turn ignition switch ON and wait at least 1 second.

2. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-1136, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198660

1.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY

1. Turn ignition switch OFF.

2. Check the voltage between ECM harness connector and ground.

DTC No.

Trouble diagnosis name

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P2100

ETC MOT PWR-B1
(Throttle control motor 
relay circuit open)

ECM detects a voltage of power source for 
throttle control motor is excessively low.

• Harness or connectors

(Throttle control motor relay circuit is 
open)

• Throttle control motor relay

P2103

ETC MOT PWR
(Throttle control motor 
relay circuit short)

ECM detect the throttle control motor relay is 
stuck ON.

• Harness or connectors

(Throttle control motor relay circuit is 
shorted)

• Throttle control motor relay

+

−

Voltage

ECM

Connector

Terminal

Connector

Terminal

F24

97

E19

152

Battery voltage

Revision: November 2015

2016 JUKE

P2100, P2103 THROTTLE CONTROL MOTOR RELAY

EC-1137

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

1. Disconnect ECM harness connector.

2. Disconnect IPDM E/R harness connector.

3. Check the continuity between ECM harness connector and IPDM E/R harness connector.

4. Also check harness for short to ground.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

3.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL

Check the voltage between ECM harness connector and ground as per the following conditions.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 4.

4.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Disconnect IPDM E/R harness connector.

4. Check the continuity between ECM harness connector and IPDM E/R harness connector.

5. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace error-detected parts.

+

−

Continuity

ECM

IPDM E/R

Connector

Terminal

Connector

Terminal

F24

97

E15

60

Existed

ECM

Condition

Voltage

(Approx.)

Connector

+

Connector

−

Terminal

Terminal

F24

118

E19

152

Ignition switch: OFF

0 V

Ignition switch: ON

Battery voltage

+

−

Continuity

ECM

IPDM E/R

Connector

Terminal

Connector

Terminal

F24

118

E15

55

Existed

Revision: November 2015

2016 JUKE

EC-1138

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

DTC Logic

INFOID:0000000012198661

DTC DETECTION LOGIC

NOTE:

•

If DTC P2101 is displayed with DTC P2100, first perform the trouble diagnosis for DTC P2100. Refer

to 

EC-1136, "DTC Logic"

.

•

If DTC P2101 is displayed with DTC P2119, first perform the trouble diagnosis for DTC P2119. Refer

to 

EC-1143, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V when

engine is running.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON and wait at least 2 seconds.

2. Start engine and let it idle for 5 seconds.

3. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-1138, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198662

1.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL

Check the voltage between ECM harness connector terminals as per the following conditions.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

DTC No.

Trouble diagnosis name

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P2101

ETC FNCTN/CIRC-B1
(Electric throttle control 
performance)

Electric throttle control function does not 
operate properly.

• Harness or connectors

(Throttle control motor circuit is open or shorted)

• Electric throttle control actuator

ECM

Condition

Voltage

(Approx.)

Connector

+

Connector

−

Terminal

Terminal

F24

118

E19

152

Ignition switch: OFF

0 V

Ignition switch: ON

Battery voltage

Revision: November 2015

2016 JUKE

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

EC-1139

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

2. Disconnect ECM harness connector.

3. Disconnect IPDM E/R harness connector.

4. Check the continuity between ECM harness connector and IPDM E/R harness connector.

5. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

1. Check the continuity between ECM harness connector and IPDM E/R harness connector.

2. Also check harness for short to ground.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

4.

CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect electric throttle control actuator harness connector.

3. Disconnect ECM harness connector.

4. Check the continuity between electric throttle control actuator harness connector and ECM harness con-

nector.

5. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts.

5.

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY 

1. Remove the intake air duct. Refer to 

EM-192, "Exploded View"

.

2. Check if foreign matter is caught between the throttle valve and the housing.
Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Remove the foreign matter and clean the electric throttle control actuator inside, then perform

throttle valve closed position learning. Refer to 

EC-754, "Description"

.

+

−

Continuity

ECM

IPDM E/R

Connector

Terminal

Connector

Terminal

F24

118

E15

55

Existed

+

−

Continuity

ECM

IPDM E/R

Connector

Terminal

Connector

Terminal

F24

97

E15

60

Existed

+

−

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F29

2

F24

120

Existed

119

Not existed

1

120

Not existed

119

Existed

Revision: November 2015

2016 JUKE

EC-1140

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

6.

CHECK THROTTLE CONTROL MOTOR

Check the throttle control motor. Refer to 

EC-1140, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace electric throttle control actuator. Refer to 

EM-197, "Exploded View"

.

Component Inspection

INFOID:0000000012198663

1.

CHECK THROTTLE CONTROL MOTOR

1. Turn ignition switch OFF.

2. Disconnect electric throttle control actuator harness connector.

3. Check the resistance between electric throttle control actuator terminals as per the following.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace electric throttle control actuator. Refer to 

EM-197, "Exploded View"

.

Electric throttle control actuator

Resistance

(Approx.)

+

−

Terminals

2

1

1 - 15 

Ω

 [at 25

°

C (77

°

F)]

Revision: November 2015

2016 JUKE

P2118 THROTTLE CONTROL MOTOR

EC-1141

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P2118 THROTTLE CONTROL MOTOR

DTC Logic

INFOID:0000000012198664

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON and wait at least 2 seconds.

2. Start engine and let it idle for 5 seconds.

3. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-1141, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198665

1.

CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect electric throttle control actuator harness connector.

3. Disconnect ECM harness connector.

4. Check the continuity between electric throttle control actuator harness connector and ECM harness con-

nector.

5. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

DTC No.

Trouble diagnosis name

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P2118

ETC MOT-B1
(Throttle control motor 
circuit short)

ECM detects short in both circuits between 
ECM and throttle control motor.

• Harness or connectors

(Throttle control motor circuit is shorted.)

• Electric throttle control actuator

(Throttle control motor)

+

−

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F29

2

F24

120

Existed

119

Not existed

1

120

Not existed

119

Existed

Revision: November 2015

2016 JUKE

EC-1142

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2118 THROTTLE CONTROL MOTOR

2.

CHECK THROTTLE CONTROL MOTOR

Check the throttle control motor. Refer to 

EC-1142, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace electric throttle control actuator. Refer to 

EM-197, "Exploded View"

.

Component Inspection

INFOID:0000000012198666

1.

CHECK THROTTLE CONTROL MOTOR

1. Turn ignition switch OFF.

2. Disconnect electric throttle control actuator harness connector.

3. Check the resistance between electric throttle control actuator terminals as per the following.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace electric throttle control actuator. Refer to 

EM-197, "Exploded View"

.

Electric throttle control actuator

Resistance

(Approx.)

+

−

Terminals

2

1

1 - 15 

Ω

 [at 25

°

C (77

°

F)]

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     288      289      290      291     ..