Nissan Juke (2016 year). Service Repair Manual - part 69

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     67      68      69      70     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 69

 

 

VEHICLE JERKS DURING

BRC-145

< SYMPTOM DIAGNOSIS >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

VEHICLE JERKS DURING

Description

INFOID:0000000012199750

The vehicle jerks when VDC function, TCS function, ABS function, EBD function or brake limited slip differen-

tial (BLSD) function operates.

Diagnosis Procedure

INFOID:0000000012199751

1.

CHECK SYMPTOM

Check that the vehicle jerks when VDC function, TCS function, ABS function, EBD function or brake limited

slip differential (BLSD) function operates.
Is the inspection result normal?

YES

>> Normal

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK CONNECTOR

With CONSULT

1. Turn the ignition switch OFF.

2. Disconnect ABS actuator and electric unit (control unit) harness connector.

3. Check the connector terminal for deformation, disconnection and looseness.

4. Connect harness connector and perform self-diagnosis for “ABS” again.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Poor connection of connector terminal. Repair or replace connector terminal.

4.

CHECK ECM AND TCM SELF-DIAGNOSIS RESULTS

With CONSULT

Perform self-diagnosis for “ENGINE” and “TRANSMISSION” (for CVT models).
Is any DTC detected?

YES

>> Check the DTC.

NO

>> Replace the ABS actuator and electric unit (control unit). Refer to 

BRC-153, "Removal and Instal-

lation"

.

Revision: November 2015

2016 JUKE

BRC-146

< SYMPTOM DIAGNOSIS >

[WITH VDC]

NORMAL OPERATING CONDITION

NORMAL OPERATING CONDITION

Description

INFOID:0000000012199752

Symptom

Result

Brake pedal slightly vibrates and operation sound (motor sound and sound from suspen-
sion) occurs when VDC function, TCS function, ABS function, EBD function or brake limited 
differential (BLSD) function operates.

This is not a malfunction, The symptom 
occurs VDC function, TCS function, ABS 
function, EBD function and brake limited 
differential (BLSD) function that are nor-
mally operated.

Brake stopping distance may become longer than models without ABS function depending 
on the road conditions, when ABS function is operated on slippery road like rough road, 
gravel road or snowy road.

Brake pedal vibrates and operation sound occurs during sudden acceleration and corner-
ing, when VDC function, TCS function or brake limited slip differential (BLSD) function is 
operated.

Brake pedal vibrates and motor sound from the engine room occurs, when the engine starts 
or the vehicle starts just after starting the engine.

This is not a malfunction, because it is 
caused by operation check of ABS actua-
tor and electric unit (control unit).

Acceleration may be felt insufficient depending on the road conditions.

This is not a malfunction, because it is 
caused by TCS function that puts the 
highest priority to obtain the optimum 
traction (stability).

TCS function may operate momentarily, while driving on a road where friction coefficient 
varies, or when downshifting, or fully depressing accelerator pedal.

ABS warning lamp and VDC OFF indicator lamp may turn ON, when the vehicle is on a ro-
tating turntable or is given a strong shaking or large vibrations on a ship while the engine is 
running.

In this case, restart the engine on a nor-
mal road. If the normal condition is re-
stored, there is no malfunction. In that 
case, erase “ABS” self-diagnosis result 
memory with CONSULT.

VDC warning lamp may turn ON and VDC function, TCS function and brake limited slip dif-
ferential (BLSD) function may not normally operate, when driving on a special road the is 
extremely slanted (bank in a circuit course).

A malfunction in yaw rate/side/decel G sensor system may be detected when the vehicle 
sharply turns during a spin turn, acceleration turn or drift driving while VDC function, TCS 
function and brake limited slip differential (BLSD) function are OFF (VDC OFF switch is 
pressed and VDC OFF indicator lamp is in ON status).

The vehicle speed does not increase, when the accelerator pedal is depressed while the 
vehicle is on a 2-wheel chassis dynamometer for speedometer check.

This is not a malfunction. (When checking 
the vehicle on a chassis dynamometer, 
operate VDC OFF switch so that TCS 
function is OFF.)

Revision: November 2015

2016 JUKE

WHEEL SENSOR

BRC-147

< REMOVAL AND INSTALLATION >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

REMOVAL AND INSTALLATION

WHEEL SENSOR

FRONT WHEEL SENSOR
FRONT WHEEL SENSOR : Exploded View

INFOID:0000000012199753

NOTE:

Front RH wheel sensor is symmetrically opposite of LH.

FRONT WHEEL SENSOR : Removal and Installation

INFOID:0000000012199754

REMOVAL

1. Remove tires.
2. Remove the fender protector (front). Refer to 

EXT-31, "Removal and Installation"

.

3. Remove front wheel sensor from steering knuckle.

CAUTION:

Never rotate and never pull front wheel sensor as much as possible, when pulling out.

4. Remove front wheel sensor harness from the vehicle.

CAUTION:

Never twist or pull front wheel sensor harness, when removing.

INSTALLATION

Note the following, and install in the reverse order of the removal.

1.

Front LH wheel sensor

2.

Front LH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

JPFIC0191GB

Revision: November 2015

2016 JUKE

BRC-148

< REMOVAL AND INSTALLATION >

[WITH VDC]

WHEEL SENSOR

• Check that there is no foreign material like iron powder or damage on inner surface of front wheel sensor

mounting hole of steering knuckle and sensor rotor. Install after cleaning when there are foreign material like

iron powder, or replace when there is a malfunction.

• Never twist front wheel sensor harness when installing front wheel

sensor. Check that grommet (2) is fully inserted to bracket (1).

Check that front wheel sensor harness is not twisted after installa-

tion.

REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View

INFOID:0000000012199755

2WD

Left side

JPFIC0209ZZ

JPFIC0192GB

1.

Rear LH wheel sensor

2.

Rear LH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

Revision: November 2015

2016 JUKE

WHEEL SENSOR

BRC-149

< REMOVAL AND INSTALLATION >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Right side

AWD

JPFIC0218GB

1.

Rear RH wheel sensor

2.

Rear RH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

Revision: November 2015

2016 JUKE

BRC-150

< REMOVAL AND INSTALLATION >

[WITH VDC]

WHEEL SENSOR

NOTE:

Rear RH wheel sensor is symmetrically opposite of LH.

REAR WHEEL SENSOR : Removal and Installation

INFOID:0000000012199756

REMOVAL

1. Remove rear wheel sensor from wheel hub and bearing assembly (2WD).

CAUTION:

Never rotate or pull rear wheel sensor as much as possible, when pulling out.

2. Remove rear wheel sensor from axle housing (AWD).

CAUTION:

Never rotate or pull rear wheel sensor as much as possible, when pulling out.

3. Remove rear wheel sensor harness from the vehicle.

CAUTION:

Never twist and never pull rear wheel sensor harness, when removing.

INSTALLATION

Note the following, and install in the reverse order of the removal.

• Check that there is no foreign material like iron powder or damage on inner surface of rear wheel sensor

mounting hole of wheel hub and bearing assembly and sensor rotor. Install after cleaning when there are for-

eign material like iron powder, or replace when there is a malfunction.

1.

Rear LH wheel sensor

2.

Rear LH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

JSFIA0525GB

Revision: November 2015

2016 JUKE

WHEEL SENSOR

BRC-151

< REMOVAL AND INSTALLATION >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

• Never twist rear wheel sensor harness when installing rear wheel

sensor. Check that grommet (2) is fully inserted to bracket (1).

Check that rear wheel sensor harness is not twisted after installa-

tion.

CAUTION:

Check that the identification line (A) of the rear wheel sensor

is faced upward.

JPFIC0209ZZ

JPFIC0198ZZ

Revision: November 2015

2016 JUKE

BRC-152

< REMOVAL AND INSTALLATION >

[WITH VDC]

SENSOR ROTOR

SENSOR ROTOR

FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation

INFOID:0000000012199757

REMOVAL

Replace wheel hub as an assembly when replacing because sensor rotor cannot be disassembled.

• Except NISMO RS: Refer to 

FAX-66, "Removal and Installation"

.

• NISMO RS: Refer to 

FAX-11, "Removal and Installation"

.

INSTALLATION

Replace wheel hub as an assembly when replacing because sensor rotor cannot be disassembled.

• Except NISMO RS: Refer to 

FAX-66, "Removal and Installation"

.

• NISMO RS: Refer to 

FAX-11, "Removal and Installation"

.

REAR SENSOR ROTOR
REAR SENSOR ROTOR : Removal and Installation

INFOID:0000000012199758

REMOVAL

2WD

Replace wheel hub as an assembly when replacing because sensor rotor cannot be disassembled. Refer to

RAX-7, "Removal and Installation"

.

AWD

1. Remove drive shaft. Refer to 

RAX-19, "Removal and Installation"

.

2. Remove sensor rotor from drive shaft. Refer to 

RAX-20, "WHEEL SIDE : Disassembly and Assembly"

.

INSTALLATION

Note the following, and install in the reverse order of the removal.

• Never reuse sensor rotor. (AWD)

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     67      68      69      70     ..