Nissan Juke (2016 year). Service Repair Manual - part 68

BRAKE WARNING LAMP

BRC-137

< DTC/CIRCUIT DIAGNOSIS >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

BRAKE WARNING LAMP

Component Function Check

INFOID:0000000012199734

1.

CHECK BRAKE WARNING LAMP FUNCTION (1)

Check that brake warning lamp in combination meter turns ON for approx. 1 second after ignition switch is

turned ON.

CAUTION:

Never start engine.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to 

BRC-137, "Diagnosis Procedure"

.

2.

CHECK BRAKE WARNING LAMP FUNCTION (2)

Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.

NOTE:

Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON).
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check the parking brake switch system. Refer to 

BRC-132, "Diagnosis Procedure"

.

3.

CHECK BRAKE WARNING LAMP FUNCTION (3)

Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated

while brake fluid level in reservoir tank is with the specified level.

NOTE:

Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is

ON).
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check the brake fluid level switch system. Refer to 

BRC-113, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012199735

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT

Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to 

BRC-129, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair / replace harness, connector, fuse, or fusible link.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK COMBINATION METER

Check the combination meter. Refer to 

MWI-22, "CONSULT Function"

.

Is the inspection result normal?

YES

>> Replace the ABS actuator and electric unit (control unit). Refer to 

BRC-153, "Removal and Instal-

lation"

.

NO

>> Repair or replace combination meter. Refer to 

MWI-64, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

BRC-138

< DTC/CIRCUIT DIAGNOSIS >

[WITH VDC]

VDC WARNING LAMP

VDC WARNING LAMP

Component Function Check

INFOID:0000000012199736

1.

CHECK VDC WARNING LAMP FUNCTION

Check that VDC warning lamp in combination meter turns ON for approx. 1 second after ignition switch is

turned ON.

CAUTION:

Never start engine.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-138, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012199737

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to 

BRC-129, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair / replace harness, connector, fuse, or fusible link.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK VDC WARNING LAMP SIGNAL

With CONSULT

1. Select “ABS”, “DATA MONITOR” and “SLIP/VDC LAMP” according to this order.

2. Turn the ignition switch OFF.

3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then

changes to “Off”.

CAUTION:

Never start engine.

Is the inspection result normal?

YES

>> Check the combination meter. Refer to 

MWI-22, "CONSULT Function"

.

NO

>> Replace the ABS actuator and electric unit (control unit). Refer to 

BRC-153, "Removal and Instal-

lation"

.

Revision: November 2015

2016 JUKE

VDC OFF INDICATOR LAMP

BRC-139

< DTC/CIRCUIT DIAGNOSIS >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

VDC OFF INDICATOR LAMP

Component Function Check

INFOID:0000000012199738

1.

CHECK VDC OFF INDICATOR LAMP FUNCTION (1)

Check that VDC OFF indicator lamp in combination meter turns ON for approx. 1 second after ignition switch

is turned ON.

CAUTION:

Never start engine.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-139, "Diagnosis Procedure"

.

2.

CHECK VDC OFF INDICATOR LAMP FUNCTION (2)

Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check the VDC OFF switch system. Refer to 

BRC-134, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012199739

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT

Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to 

BRC-129, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair / replace harness, connector, fuse, or fusible link.

2.

CHECK VDC OFF INDICATOR LAMP SIGNAL (1)

With CONSULT

1. Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.

2. Turn the ignition switch OFF.

3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then

changes to “Off”.

CAUTION:

Never start engine.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the ABS actuator and electric unit (control unit). Refer to 

BRC-153, "Removal and Instal-

lation"

.

3.

CHECK VDC OFF INDICATOR LAMP SIGNAL (2)

With CONSULT

1. Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.

2. Check that data monitor displays “On” or “Off” each time when VDC OFF switch is operated.
Is the inspection result normal?

YES

>> Check the combination meter. Refer to 

MWI-22, "CONSULT Function"

.

NO

>> Check the VDC OFF switch system. Refer to 

BRC-157, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

BRC-140

< SYMPTOM DIAGNOSIS >

[WITH VDC]

EXCESSIVE OPERATION FREQUENCY

SYMPTOM DIAGNOSIS

EXCESSIVE OPERATION FREQUENCY

Description

INFOID:0000000012199740

VDC function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function

operates in excessive operation frequency.

Diagnosis Procedure

INFOID:0000000012199741

1.

CHECK BRAKING FORCE

Check the brake force using a brake tester.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check the brake system.

2.

CHECK FRONT AND REAR AXLE

Check that there is no excessive looseness in front and rear axle.

• Front axle

- NISMO RS: Refer to 

FAX-9, "Inspection"

.

- Except for NISMO RS: Refer to 

FAX-64, "Inspection"

.

• Rear axle

- 2WD: Refer to 

RAX-6, "Inspection"

.

- AWD: Refer to 

RAX-14, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair / replace error-detecting of front or rear axle part.

3.

CHECK WHEEL SENSOR

Check the wheel sensor.

• Check the installation and damage of wheel sensor.

• Check the connection of wheel sensor harness connector.

• Check the terminal of wheel sensor harness connector.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace wheel sensor.

• Front wheel sensor: Refer to 

BRC-147, "FRONT WHEEL SENSOR : Removal and Installation"

.

• Rear wheel sensor: Refer to 

BRC-150, "REAR WHEEL SENSOR : Removal and Installation"

.

4.

CHECK SENSOR ROTOR

Check that there is no looseness, damage or foreign material on sensor rotor.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair installation or replace sensor rotor.

• Front sensor rotor: Refer to 

BRC-152, "FRONT SENSOR ROTOR : Removal and Installation"

.

• Rear sensor rotor. Refer to 

BRC-152, "REAR SENSOR ROTOR : Removal and Installation"

.

5.

CHECK WARNING LAMP TURNS OFF

Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after

key switch is turned ON and stay in OFF status during driving.

CAUTION:

Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake

fluid is less than the specified level (brake fluid level switch is ON).

Is the inspection result normal?

YES

>> Normal

NO

>> Perform self-diagnosis for “ABS” with CONSULT.

Revision: November 2015

2016 JUKE

UNEXPECTED BRAKE PEDAL REACTION

BRC-141

< SYMPTOM DIAGNOSIS >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

UNEXPECTED BRAKE PEDAL REACTION

Description

INFOID:0000000012199742

A malfunction of brake pedal feel (height or others) is detected when brake pedal is depressed.

Diagnosis Procedure

INFOID:0000000012199743

1.

CHECK FRONT AND REAR AXLE

Check that there is no excessive looseness in front and rear axle.

• Front axle

- NISMO RS: Refer to 

FAX-9, "Inspection"

.

- Except for NISMO RS: Refer to 

FAX-64, "Inspection"

.

• Rear axle

- 2WD: Refer to 

RAX-6, "Inspection"

.

- AWD: Refer to 

RAX-14, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair / replace error-detecting of front or rear axle part.

2.

CHECK DISC ROTOR

Check the disc rotor runout.

• Front: Refer to 

BR-16, "DISC ROTOR : Inspection and Adjustment"

.

• Rear: Refer to 

BR-18, "DISC ROTOR : Inspection and Adjustment"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Refinish disc rotor.

• Front: Refer to 

BR-16, "DISC ROTOR : Inspection and Adjustment"

.

• Rear: Refer to 

BR-18, "DISC ROTOR : Inspection and Adjustment"

.

3.

CHECK BRAKE FLUID LEAKAGE

Check the fluid leakage.

• Front: Refer to 

BR-27, "FRONT : Inspection"

.

• Rear: Refer to 

BR-37, "REAR : Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair / replace fluid leakage part.

4.

CHECK BRAKE PEDAL

Check the each item of brake pedal. Refer to 

BR-9, "Inspection and Adjustment"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Adjust each item of brake pedal. Refer to 

BR-9, "Inspection and Adjustment"

.

5.

CHECK BRAKING FORCE

Check the brake force using a brake tester.
Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Check the each components of brake system.

6.

CHECK BRAKE PERFORMANCE

Disconnect ABS actuator and electric unit (control unit) harness connector so that ABS does not operate.

Check that brake force is normal in this condition. Connect harness connectors after checking.
Is the inspection result normal?

YES

>> Normal

NO

>> Check the each components of brake system.

Revision: November 2015

2016 JUKE

BRC-142

< SYMPTOM DIAGNOSIS >

[WITH VDC]

THE BRAKING DISTANCE IS LONG

THE BRAKING DISTANCE IS LONG

Description

INFOID:0000000012199744

Brake stopping distance is long when ABS function is operated.

Diagnosis Procedure

INFOID:0000000012199745

CAUTION:

Brake stopping distance on slippery road like rough road, gravel road or snowy road may become

longer when ABS is operated than when ABS is not operated.

1.

CHECK BRAKING FORCE

Check the brake force using a brake tester.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check the each components of brake system.

2.

CHECK BRAKE PERFORMANCE

Disconnect ABS actuator and electric unit (control unit) harness connector so that ABS does not operate.

Check the brake stopping distance in this condition. Connect harness connectors after checking.
Is the inspection result normal?

YES

>> Normal

NO

>> Check the each components of brake system.

Revision: November 2015

2016 JUKE

DOES NOT OPERATE

BRC-143

< SYMPTOM DIAGNOSIS >

[WITH VDC]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

DOES NOT OPERATE

Description

INFOID:0000000012199746

VDC function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function

does not operate.

Diagnosis Procedure

INFOID:0000000012199747

CAUTION:

• VDC function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD)

function never operate when the vehicle speed is 10 km/h (6.2 MPH) or less.

• VDC function and TCS function never operate when VDC OFF switch is operated (when VDC OFF

indicator lamp turns ON).

1.

CHECK WARNING LAMP

Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn ON and turn OFF approx. 1

second after key switch is turned ON. Check that ABS warning lamp, brake warning lamp and VDC warning

lamp and stay in OFF status during driving.

CAUTION:

Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake

fluid is less than the specified level (brake fluid level switch is ON).

Is the inspection result normal?

YES

>> Normal

NO

>> Perform self-diagnosis for “ABS” with CONSULT.

Revision: November 2015

2016 JUKE

BRC-144

< SYMPTOM DIAGNOSIS >

[WITH VDC]

BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS

BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS

Description

INFOID:0000000012199748

• Brake pedal vibrates and motor sound from ABS actuator and electric unit (control unit) occurs, when the

engine starts.

• Brake pedal vibrates during braking.

CAUTION:

Vibration may be felt during brake pedal is lightly depressed (just placing a foot on it) in the following

conditions. This is normal.

• When shifting gears

• When driving on slippery road

• During cornering at high speed

• When passing over bumps or grooves [Approx. 50 mm (1.97 in) or more]

• When pulling away just after starting engine [at approx. 10 km/h (6.2 MPH) or higher]

Diagnosis Procedure

INFOID:0000000012199749

1.

SYMPTOM CHECK 1

Check that there are pedal vibrations when the engine is started.
Do vibrations occur?

YES

>> GO TO 2.

NO

>> Check the brake pedal. Refer to 

BR-21, "Inspection and Adjustment"

.

2.

SYMPTOM CHECK 2

Check that motor noise from ABS actuator and electric unit (control unit) occurs when the engine starts.
Does the operation sound occur?

YES

>> GO TO 3.

NO

>> Perform self-diagnosis for “ABS” with CONSULT.

3.

SYMPTOM CHECK 3

Check the symptoms when electrical component (headlamps, etc.) switches are operated.
Does the symptom occur?

YES

>> Check that radio (including wiring), antenna and antenna lead-in wires are not located near ABS

actuator and electric unit (control unit). Move them if they are located near ABS actuator and elec-

tric unit (control unit).

NO

>> Normal

Revision: November 2015

2016 JUKE