Nissan Juke F15. Manual - part 708

EXL-52

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

HEADLAMP (HI) CIRCUIT

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace harness.

9.

CHECK DAYTIME RUNNING LIGHT RELAY

Check daytime running light relay. Refer to 

EXL-52, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Replace daytime running light relay.

10.

CHECK HEADLAMP (HI) RH BULB

Check the headlamp (HI) RH bulb.
Is the inspection result normal?

YES

>> Check the headlamp (HI) RH harness. Repair or replace if necessary.

NO

>> Replace headlamp (HI) RH bulb. Refer to 

EXL-96, "Replacement"

.

11.

CHECK HEADLAMP (HI) LH GROUND CIRCUIT

Check continuity between headlamp harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace harness.

12.

CHECK HEADLAMP (HI) LH BULB

Check the headlamp (HI) LH bulb.
Is the inspection result normal?

YES

>> Check the headlamp (HI) LH harness. Repair or replace if necessary.

NO

>> Replace headlamp (HI) LH bulb. Refer to 

EXL-96, "Replacement"

.

Component Inspection

INFOID:0000000012201638

1.

CHECK DAYTIME RUNNING LIGHT RELAY

1. Turn ignition switch OFF.

2. Remove daytime running light relay.

3. Apply battery voltage to daytime running light relay between terminals 2 and 1.

4. Check continuity of daytime running light relay terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace daytime running light relay.

Daytime running light relay

—

Continuity

Connector

Terminal

E65

4

Ground

Existed

Headlamp

—

Continuity

Connector

Terminal

E54

3

Ground

Existed

Daytime running light relay

Condition

Continuity

Terminal

3

4

Battery voltage

Apply

Not existed

Not apply

Existed

HEADLAMP (LO) CIRCUIT

EXL-53

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

HEADLAMP (LO) CIRCUIT

Component Function Check

INFOID:0000000012201639

1.

CHECK HEADLAMP (LO) OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the headlamp (LO) is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the headlamp (LO) is turned ON.
Is the inspection result normal?

YES

>> Headlamp (LO) circuit is normal.

NO

>> Refer to 

EXL-53, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201640

1.

CHECK HEADLAMP (LO) FUSE

1. Turn ignition switch OFF.

2. Check that the following fuses are not blown (open).

Is the fuse blown (open)?

YES

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).

NO

>> GO TO 2.

2.

CHECK HEADLAMP (LO) POWER SUPPLY

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

3.

CHECK HEADLAMP (LO) POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and headlamp connector.

3. Check continuity between IPDM E/R harness connector and headlamp harness connector.

Lo

: Headlamp (LO) ON

Off

: Headlamp (LO) OFF

Unit

Location

Fuse No.

Capacity

Headlamp LO (RH)

IPDM E/R

#54

15 A

Headlamp LO (LH)

#53

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

RH

E15

52

Ground

EXTERNAL 
LAMPS

LO

9 – 16 V

Off

0 – 1 V

LH

51

LO

9 – 16 V

Off

0 – 1 V

EXL-54

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

HEADLAMP (LO) CIRCUIT

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK HEADLAMP (LO) GROUND CIRCUIT

Check continuity between headlamp harness connector and ground.

Is the inspection result normal?

YES

>> Perform the xenon headlamp diagnosis. Refer to 

EXL-55, "Diagnosis Procedure"

.

NO

>> Repair or replace harness.

IPDM E/R

Headlamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E15

52

E55

4

Existed

LH

51

E54

Headlamp

—

Continuity

Connector

Terminal

RH

E55

2

Ground

Existed

LH

E54

XENON HEADLAMP

EXL-55

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

XENON HEADLAMP

Diagnosis Procedure

INFOID:0000000012201641

1.

CHECK XENON BULB

Install the normal bulb to the applicable headlamp. Check that the headlamp (LO) is turned ON.
Is the headlamp (LO) turned ON?

YES

>> Replace the corresponding xenon bulb. Refer to 

EXL-96, "Replacement"

.

NO

>> GO TO 2.

2.

CHECK XENON HEADLAMP

Install the normal headlamp assembly to the applicable headlamp. Check that the headlamp (LO) is turned

ON.
Is the headlamp (LO) turned ON?

YES

>> Replace the corresponding headlamp assembly. Refer to 

EXL-96, "Removal and Installation"

.

NO

>> Xenon headlamp is normal.