Nissan Juke F15. Manual - part 405

 

  Index      Nissan     Nissan Juke F15 (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  403  404  405  406   ..

 

 

Nissan Juke F15. Manual - part 405

 

 

P1078 EVT CONTROL POSITION SENSOR

EC-433

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace EVT control position sensor. Refer to 

EM-76, "Exploded View"

.

EVT control position sensor

Resistance

+

Terminal

1

2

Except 0 or 

∞ Ω [at 25°C (77°F)]

3

2

3

EC-434

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P1148 CLOSED LOOP CONTROL

P1148 CLOSED LOOP CONTROL

DTC Logic

INFOID:0000000012197983

DTC DETECTION LOGIC

NOTE:

DTC P1148 is displayed with DTC for A/F sensor 1.

When the DTC is detected, perform the trouble diagnosis of DTC corresponding to A/F sensor 1.

Diagnosis Procedure

INFOID:0000000012197984

DTC P1148 is displayed with DTC for A/F sensor 1. 

When the DTC is detected, perform the trouble diagnosis of DTC corresponding to A/F sensor 1.

Refer to 

EC-115, "DTC Index"

.

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P1148

CLOSED LOOP-B1
(Closed loop control func-
tion)

The closed loop control function does not 
operate even when vehicle is being driven in 
the specified condition.

• Harness or connectors

(A/F sensor 1 circuit is open or shorted.)

• A/F sensor 1
• A/F sensor 1 heater

P1197 OUT OF GAS

EC-435

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P1197 OUT OF GAS

Description

INFOID:0000000012197985

This diagnosis result is detected when the fuel level of the fuel tank is extremely low and the engine does not

run normally.

DTC Logic

INFOID:0000000012197986

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE-I

Start the engine.
Does the engine start?

YES

>> GO TO 3.

NO

>> Proceed to 

EC-435, "Diagnosis Procedure"

.

3.

PERFORM DTC CONFIRMATION PROCEDURE-II

1. Warm up the engine to the normal operating temperature.

NOTE:

For best results, warm up the engine until “COOLAN TEMP/S” on “DATA MONITOR” mode of “ENGINE”

using CONSULT reaches at least 70

°C (158°F).

2. Keep the engine speed at 3,500 rpm for 5 seconds and let it idle at least 60 seconds.

3. Check the 1st trip DTC.

NOTE:

If the fuel tank has sufficient fuel, this diagnosis result may not be detected.

Is 1st trip DTC detected?

YES

>> Proceed to 

EC-435, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197987

1.

REFUEL THE VEHICLE

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P1197

FUEL RUN OUT
(Out of gas)

• Fuel rail pressure remains at 1.1 MPa (11 

bar, 11.2 kg/cm

2

, 159.5 psi) or less for 5 

seconds or more with the fuel level too 
low.

• Fuel rail pressure remains 2.7 MPa (27 

bar, 27.5 kg/cm

2

, 392 psi) lower than a tar-

get fuel pressure for 5 seconds or more 
with the fuel level too low.

• Out of gas
• Harness or connectors (Low pressure fuel 

pump circuit is open or shorted.)

• Low pressure fuel pump
• Fuel pressure regulator
• Low pressure fuel system
• Harness or connectors (High pressure fuel 

pump circuit is shorted.)

• High pressure fuel pump
• High pressure fuel system
• Fuel rail pressure sensor
• Disconnection of the fuel hose

EC-436

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P1197 OUT OF GAS

1. Refuel 10 liter (10 US qt, 8 imp qt).

CAUTION:

Never refuel more than 10 liter.

2. Start the engine and keep the engine speed at 3,000 rpm for 30 seconds.

NOTE:

For best results, warm up the engine until “COOLAN TEMP/S” on “DATA MONITOR” mode of “ENGINE”

using CONSULT reaches at least 70

°C (158°F).

3. Turn ignition switch OFF and wait at least 10 seconds.

4. Turn ignition switch ON.

5. Turn ignition switch OFF and wait at least 10 seconds.

6. Turn ignition switch ON.

7. Erase the DTC.

8. Start the engine and let it idle at least 60 seconds.

9. Perform DTC confirmation procedure again. Refer to 

EC-435, "DTC Logic"

.

Is 1st trip DTC detected?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

CHECK LOW PRESSURE FUEL PUMP

Refer to 

EC-546, "Component Function Check"

 .

Is inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK HIGH PRESSURE FUEL PUMP

Refer to 

EC-549, "Component Function Check"

.

Is inspection result normal?

YES

>> Check the fuel hose for disconnection and looseness.

NO

>> Repair or replace error-detected parts.

 

 

 

 

 

 

 

Content   ..  403  404  405  406   ..