Nissan Juke F15. Manual - part 266

P183D SIDE G SENSOR

DLN-69

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P183D SIDE G SENSOR

DTC Logic

INFOID:0000000012199417

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183D” detected?

YES

>> Proceed to 

DLN-69, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199418

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 2.

2.

ERASE SELF-DIAGNOSTIC RESULT

With CONSULT

1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

3. Stop the vehicle.

4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> Refer to 

BRC-136, "Component Function Check"

.

3.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183D”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P183D

SIDE G SENSOR

Malfunction is detected in side G sensor 
signal that is output from ABS actuator 
and electric unit (control unit) through 
CAN communication.

• ABS actuator and electric unit (control 

unit)

• Yaw rate/side/decel G sensor (Side G 

sensor signal)

• AWD control module
• CAN communication line

DLN-70

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P183E YAW RATE SENSOR

P183E YAW RATE SENSOR

DTC Logic

INFOID:0000000012199419

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183E” detected?

YES

>> Proceed to 

DLN-70, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199420

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 2.

2.

ERASE SELF-DIAGNOSTIC RESULT

With CONSULT

1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

3. Stop the vehicle.

4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> Refer to 

BRC-136, "Component Function Check"

.

3.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183E”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P183E

YAWRATE SENSOR

Malfunction is detected in yaw rate sen-
sor signal that is output from ABS actua-
tor and electric unit (control unit) through 
CAN communication.

• ABS actuator and electric unit (control 

unit)

• Yaw rate/side/decel G sensor (Yaw 

rate signal)

• AWD  control  module
• CAN communication line

P183F GEAR POSITION SIGNAL

DLN-71

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P183F GEAR POSITION SIGNAL

DTC Logic

INFOID:0000000012199421

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine.

CAUTION:

Never drive the vehicle.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183F” detected?

YES

>> Proceed to 

DLN-71, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199422

1.

PERFORM TCM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “TRANSMISSION”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

TM-203, "DTC Index"

 (RE0F10B), 

TM-414,

"DTC Index"

 (RE0F10D).

NO

>> GO TO 2.

2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183F”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P183F

GEAR POSI SIGNAL

Malfunction is detected in current gear 
position signal that is output from TCM 
through CAN communication.

• Sensor related to CVT
• TCM
• AWD control module
• CAN communication line

DLN-72

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P1840 OUTPUT SPEED SIGNAL

P1840 OUTPUT SPEED SIGNAL

DTC Logic

INFOID:0000000012199423

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1840” detected?

YES

>> Proceed to 

DLN-72, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199424

1.

PERFORM TCM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “TRANSMISSION”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

TM-203, "DTC Index"

 (RE0F10B), 

TM-414,

"DTC Index"

 (RE0F10D).

NO

>> GO TO 2.

2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1840”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1840

OUTPUT SPEED SIGNAL

Malfunction is detected in output shaft 
revolution signal that is output from TCM 
through CAN communication.

• Sensor related to CVT
• TCM
• AWD  control  module
• CAN communication line