Nissan Juke F15. Manual - part 264

P182E AWD SOLENOID (RIGHT)

DLN-61

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK AWD SOLENOID CIRCUIT (2)

1. Disconnect rear final drive sub-harness connector.

2. Check the continuity between AWD control module harness connector and rear final drive sub-harness

connector.

3. Check the continuity between AWD control module harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the error-detected parts.

3.

CHECK REAR FINAL DRIVE SUB-HARNESS

1. Disconnect electric controlled coupling (right) harness connector.

2. Check the continuity between rear final drive sub-harness connector and electric controlled coupling

(right) harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace rear final drive sub-harness. Refer to 

DLN-145, "Exploded View"

.

4.

CHECK AWD SOLENOID

Check AWD solenoid. Refer to 

DLN-62, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to 

DLN-

145, "Removal and Installation"

.

5.

CHECK TERMINALS AND HARNESS CONNECTORS

1. Check AWD control module pin terminals for damage or loose connection with harness connector.

2. Check rear final drive sub-harness pin terminals for damage or loose connection with harness connector.

AWD control module

Condition

 Resistance (Approx.)

Connector

Terminal

B47

25

26

10

°C (50°F)

2.55 

Ω

20

°C (68°F)

2.65 

Ω

30

°C (86°F)

2.76 

Ω

AWD control module

Rear final drive sub-harness

Continuity

Connector

Terminal

Connector

Terminal

B47

25

B64

2

Existed

26

6

AWD control module

—

Continuity

Connector

Terminal

B47

25

Ground

Not existed

26

Rear final drive sub-harness

Electric controlled coupling (right)

Continuity

Connector

Terminal

Connector

Terminal

B84

2

B86

2

Existed

6

6

DLN-62

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P182E AWD SOLENOID (RIGHT)

3. Check electric controlled coupling (right) pin terminals for damage or loose connection with harness con-

nector.

Is the inspection result normal?

YES

>> Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace the error-detected parts.

Component Inspection

INFOID:0000000012199406

1.

CHECK AWD SOLENOID

1. Turn the ignition switch OFF.

2. Disconnect electric controlled coupling (right) harness connector.

3. Check the resistance between electric controlled coupling (right) connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to 

DLN-

145, "Removal and Installation"

.

Electric controlled coupling (right)

Condition

 Resistance (Approx.)

Terminal

2

6

10

°C (50°F)

2.55 

Ω

20

°C (68°F)

2.65 

Ω

30

°C (86°F)

2.75 

Ω

P1830 ABS OPERATION SIGNAL

DLN-63

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P1830 ABS OPERATION SIGNAL

DTC Logic

INFOID:0000000012199407

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1830” detected?

YES

>> Proceed to 

DLN-63, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199408

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 2.

2.

ERASE SELF-DIAGNOSTIC RESULT

With CONSULT

1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.

3. Stop the vehicle.

4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> Refer to 

BRC-136, "Component Function Check"

.

3.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1830”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1830

ABS OP SIG

Malfunction is detected in ABS operation 
signal that is output from ABS actuator 
and electric unit (control unit) through 
CAN communication.

• ABS actuator and electric unit (control 

unit)

• AWD control module
• CAN communication line

DLN-64

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P1831 VDC OPERATION SIGNAL

P1831 VDC OPERATION SIGNAL

DTC Logic

INFOID:0000000012199409

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1831” detected?

YES

>> Proceed to 

DLN-64, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199410

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 2.

2.

ERASE SELF-DIAGNOSTIC RESULT

With CONSULT

1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.

3. Stop the vehicle.

4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> Refer to 

BRC-136, "Component Function Check"

.

3.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1831”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1831

VDC OP SIG

Malfunction is detected in VDC opera-
tion signal that is output from ABS actu-
ator and electric unit (control unit) 
through CAN communication.

• ABS actuator and electric unit (control 

unit)

• AWD  control  module
• CAN communication line