Nissan Juke F15. Manual - part 263

P182D AWD SOLENOID (LEFT)

DLN-57

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P182D AWD SOLENOID (LEFT)

DTC Logic

INFOID:0000000012199401

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION (1)

With CONSULT

1. Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.

2. Turn the ignition switch OFF.

3. Turn the ignition switch ON, and then wait for 5 seconds or more.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?

YES

>> Proceed to 

DLN-57, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION (2)

With CONSULT

1. Lift up the vehicle.

2. Start the engine, and run at idle for 1 second.

3. Stop the engine.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?

YES

>> Proceed to 

DLN-57, "Diagnosis Procedure"

.

NO

>> GO TO 4.

4.

PERFORM DTC CONFIRMATION (3)

With CONSULT

1. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.

2. Stop the vehicle.

3. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.

4. Stop the vehicle.

5. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?

YES

>> Proceed to 

DLN-57, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199402

1.

CHECK AWD SOLENOID CIRCUIT (1)

1. Turn the ignition switch OFF.

2. Disconnect AWD control module harness connector.

3. Check the resistance between AWD control module harness connector.

DTC

Display item

Malfunction detected condition

Possible cause

P182D

SOLENOID LEFT

Malfunction related to AWD solenoid 
(left) has been detected.

• Internal malfunction of electric con-

trolled coupling (left)

• Malfunction of AWD solenoid (left) 

power supply circuit (open or short)

• Malfunction of AWD control module

DLN-58

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P182D AWD SOLENOID (LEFT)

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK AWD SOLENOID CIRCUIT (2)

1. Disconnect rear final drive sub-harness connector.

2. Check the continuity between AWD control module harness connector and rear final drive sub-harness

connector.

3. Check the continuity between AWD control module harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the error-detected parts.

3.

CHECK REAR FINAL DRIVE SUB-HARNESS

1. Disconnect electric controlled coupling (left) harness connector.

2. Check the continuity between rear final drive sub-harness connector and electric controlled coupling (left)

harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace rear final drive sub-harness. Refer to 

DLN-145, "Exploded View"

.

4.

CHECK AWD SOLENOID

Check AWD solenoid. Refer to 

DLN-59, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to 

DLN-

145, "Removal and Installation"

.

5.

CHECK TERMINALS AND HARNESS CONNECTORS

1. Check AWD control module pin terminals for damage or loose connection with harness connector.

2. Check rear final drive sub-harness pin terminals for damage or loose connection with harness connector.

AWD control module

Condition

 Resistance (Approx.)

Connector

Terminal

B47

23

24

10

°C (50°F)

2.55 

Ω

20

°C (68°F)

2.65 

Ω

30

°C (86°F)

2.76 

Ω

AWD control module

Rear final drive sub-harness

Continuity

Connector

Terminal

Connector

Terminal

B47

23

B64

4

Existed

24

8

AWD control module

—

Continuity

Connector

Terminal

B47

23

Ground

Not existed

24

Rear final drive sub-harness

Electric controlled coupling (left)

Continuity

Connector

Terminal

Connector

Terminal

B84

4

B85

4

Existed

8

8

P182D AWD SOLENOID (LEFT)

DLN-59

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

3. Check electric controlled coupling (left) pin terminals for damage or loose connection with harness con-

nector.

Is the inspection result normal?

YES

>> Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace the error-detected parts.

Component Inspection

INFOID:0000000012199403

1.

CHECK AWD SOLENOID

1. Turn the ignition switch OFF.

2. Disconnect electric controlled coupling (left) harness connector.

3. Check the resistance between electric controlled coupling (left) connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to 

DLN-

145, "Removal and Installation"

.

Electric controlled coupling (left)

Condition

 Resistance (Approx.)

Terminal

4

8

10

°C (50°F)

2.55 

Ω

20

°C (68°F)

2.65 

Ω

30

°C (86°F)

2.76 

Ω

DLN-60

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P182E AWD SOLENOID (RIGHT)

P182E AWD SOLENOID (RIGHT)

DTC Logic

INFOID:0000000012199404

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION (1)

With CONSULT

1. Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.

2. Turn the ignition switch OFF.

3. Turn the ignition switch ON, and then wait for 5 seconds or more.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?

YES

>> Proceed to 

DLN-60, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION (2)

With CONSULT

1. Lift up the vehicle.

2. Start the engine, and run at idle for 1 second.

3. Stop the engine.

4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?

YES

>> Proceed to 

DLN-60, "Diagnosis Procedure"

.

NO

>> GO TO 4.

4.

PERFORM DTC CONFIRMATION (3)

With CONSULT

1. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.

2. Stop the vehicle.

3. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.

4. Stop the vehicle.

5. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?

YES

>> Proceed to 

DLN-60, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199405

1.

CHECK AWD SOLENOID CIRCUIT (1)

1. Turn the ignition switch OFF.

2. Disconnect AWD control module harness connector.

3. Check the resistance between AWD control module harness connector.

DTC

Display item

Malfunction detected condition

Possible cause

P182E

SOLENOID RIGHT

Malfunction related to AWD solenoid 
(right) has been detected.

• Internal malfunction of electric con-

trolled coupling (right)

• Malfunction of AWD solenoid (right) 

power supply circuit (open or short)

• Malfunction of AWD control module