Nissan Juke F15. Manual - part 231

DLK-104

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000012196684

1.

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1. Select “DOOR LOCK” of “BCM” using CONSULT.

2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

Refer to 

DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

2.

CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1. Select “DOOR LOCK” of “BCM” using CONSULT.

2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

Refer to 

DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Confirm the operation after replacement.
Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-

ATE

DLK-105

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE

Diagnosis Procedure

INFOID:0000000012196685

1.

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1. Select “DOOR LOCK” of “BCM” using CONSULT.

2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

Refer to 

DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

2.

CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”

1. Select “DOOR LOCK” of “BCM” using CONSULT.

2. Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.

Refer to 

DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.

3.

CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1. Select “DOOR LOCK” of “BCM” using CONSULT.

2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

3. Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

Refer to 

DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

4.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Confirm the operation after replacement.
Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

DLK-106

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000012196686

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1 >> Refer to 

BCS-62, "DTC Index"

. (BCM)

NO-2 >> Refer to 

MWI-33, "DTC Index"

. (Combination meter)

2.

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.

3. Check the “HAZARD ANSWER BACK” in “WORK SUPPORT”.

Refer to 

DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “HAZARD ANSWER BACK” in “WORK SUPPORT”.

3.

CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.

3. Check the “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.

Refer to 

DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.

4.

CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.

3. Check the “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.

Refer to 

DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Set “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.

5.

CHECK HAZARD FUNCTION

Check hazard function.

Refer to 

DLK-80, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.

Refer to 

DLK-82, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Confirm the operation after replacement. 
Is the result normal?

YES

>> INSPECTION END

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

DLK-107

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

NO

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.