Nissan Juke F15. Manual - part 220

DLK-60

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

BACK DOOR OPENER ACTUATOR

Is the inspection normal?

YES

>> Replace back door lock assembly.

NO

>> Repair or replace harness.

Back door lock assembly

Ground

Continuity

Connector

Terminal

D106

2

Existed

BACK DOOR OPENER SWITCH

DLK-61

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR OPENER SWITCH

Component Function Check

INFOID:0000000012196616

1.

CHECK FUNCTION

1. Select “TRUNK” of “BCM” using CONSULT.

2. Select “TR/BD OPEN SW” in “DATA MONITOR” mode.

3. Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Back door opener switch is OK.

NO

>> Refer to 

DLK-61, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196617

1.

CHECK BACK DOOR OPENER SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect back door opener switch connector.

3. Check signal between back door opener switch harness connector and ground using oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK BACK DOOR OPENER SWITCH CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and back door opener switch harness connector.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

Monitor item

Condition

Status

TR/BD OPEN SW

Back door opener switch

Pressed

ON

Released

OFF

(+)

(–)

Signal

(Reference value)

Back door opener switch

Connector

Terminal 

D107

1

Ground

JPMIA0012GB

BCM

Back door opener switch

Continuity 

Connector

Terminal

Connector

Terminal

M68

30

D107

1

Existed

BCM

Ground

Continuity 

Connector

Terminal

M68

30

Not existed

DLK-62

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

BACK DOOR OPENER SWITCH

3.

CHECK BACK DOOR OPENER SWITCH GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK BACK DOOR OPENER SWITCH

Refer to 

DLK-62, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace back door opener switch.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000012196618

1.

CHECK BACK DOOR OPENER SWITCH

1. Turn ignition switch OFF.

2. Disconnect back door opener switch connector.

3. Check continuity between back door opener switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace back door opener switch.

Back door opener switch

Ground

Continuity 

Connector

Terminal

D107

2

Existed

Back door opener switch

Condition

Continuity 

Terminal 

1

2

Back door opener 
switch

Pressed

Existed

Released

Not existed

BACK DOOR REQUEST SWITCH

DLK-63

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR REQUEST SWITCH

Component Function Check

INFOID:0000000012196619

1.

CHECK FUNCTION

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “REQ SW-BD/TR” in “DATA MONITOR” mode.

3. Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Back door request switch is OK.

NO

>> Refer to 

DLK-63, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196620

1.

CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect back door opener switch connector.

3. Check voltage between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK BACK DOOR REQUEST SWITCH CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and back door opener switch harness connector.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair harness or connector.

3.

CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Monitor item

Condition

Status

REQ SW-BD/TR

Back door request switch

Pressed

On

Released

Off

(+)

(–)

Voltage

(Approx.)

Back door opener switch

Connector

Terminal 

D107

3

Ground

12 V

BCM

Back door opener switch

Continuity 

Connector

Terminal

Connector

Terminal

M68

51

D107

3

Existed

BCM

Ground

Continuity 

Connector

Terminal

M68

51

Not existed

Back door opener switch

Ground

Continuity 

Connector

Terminal

D107

4

Existed