Nissan Juke F15. Manual - part 1384

WW-32

< DTC/CIRCUIT DIAGNOSIS >

FRONT WIPER MOTOR HI CIRCUIT

FRONT WIPER MOTOR HI CIRCUIT

Component Function Check

INFOID:0000000012197055

1.

CHECK FRONT WIPER HI OPERATION

CONSULT ACTIVE TEST

1. Select “FRONT WIPER” of IPDM E/R active test item.

2. With operating the test item, check front wiper operation.

Is front wiper (HI) operation normally?

YES

>> Front wiper motor HI circuit is normal.

NO

>> Refer to 

WW-32, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012197056

1.

CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1. Turn ignition switch OFF.

2. Disconnect front wiper motor connector.

3. Turn ignition switch ON.

4. Select “FRONT WIPER” of IPDM E/R active test item.

5. With operating the test item, check voltage between front wiper motor harness connector and ground.

*: According to front wiper protection function, IPDM E/R supplies voltage for 10 seconds (battery voltage) and

then stops for 20 seconds (0 V). This operations occurs repeatedly.
Is the inspection result normal?

YES

>> Replace front wiper motor.

NO

>> GO TO 2.

2.

CHECK FRONT WIPER MOTOR (HI) CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

4. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace harness.

Hi

: Front wiper (HI) operation

Off

: Stop the front wiper.

(+)

(

−)

Condition

Voltage (Approx.)

Front wiper motor

Connector

Terminal

E20

1

Ground

FRONT WIPER

Hi

Battery voltage

(10 seconds*)

IPDM E/R

Front wiper motor

Continuity

Connector

Terminal

Connector

Terminal

E14

39

E20

1

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E14

39

Not existed

FRONT WIPER STOP POSITION SIGNAL CIRCUIT

WW-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

FRONT WIPER STOP POSITION SIGNAL CIRCUIT

Component Function Check

INFOID:0000000012197057

1.

CHECK FRONT WIPER STOP POSITION SIGNAL

CONSULT DATA MONITOR

1. Select “WIP AUTO STOP” of IPDM E/R data monitor item.

2. Operate the front wiper.

3. With the front wiper operation, check the monitor status.

Is the status of item normal?

YES

>> Front wiper stop position signal circuit is normal.

NO

>> Refer to 

WW-33, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012197058

1.

CHECK IPDM E/R OUTPUT VOLTAGE

1. Turn ignition switch OFF.

2. Disconnect front wiper motor connector.

3. Turn ignition switch ON.

4. Check voltage between front wiper motor harness connector and ground.

Is the inspection result normal?

YES

>> Replace front wiper motor.

NO

>> GO TO 2.

2.

CHECK FRONT WIPER MOTOR CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

4. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace harness.

Monitor item

Condition

Monitor status

WIP AUTO STOP

Front wiper motor

Stop position

STOP P

Except stop position

ACT P

(+)

(

−)

Voltage (Approx.)

Front wiper motor

Connector

Terminal

E20

4

Ground

Battery voltage

IPDM E/R 

Front wiper motor

Continuity

Connector

Terminal

Connector

Terminal

E13

25

E20

4

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E13

25

Not existed

WW-34

< DTC/CIRCUIT DIAGNOSIS >

FRONT WIPER MOTOR GROUND CIRCUIT

FRONT WIPER MOTOR GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000012197059

1.

CHECK FRONT WIPER MOTOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect front wiper motor connector.

3. Check continuity between front wiper motor harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace harness.

Front wiper motor

Ground

Continuity

Connector

Terminal

E20

5

Existed

WASHER SWITCH

WW-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

WASHER SWITCH

Component Inspection

INFOID:0000000012197060

1.

CHECK WASHER SWITCH

1. Turn ignition switch OFF.

2. Disconnect combination switch connector.

3. Check continuity between the combination switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace combination switch (Wiper and washer switch).

A

:  Terminal  4

B

:  Terminal  6

C

:  Terminal  3

D

:  Terminal  1

JPLIA0164GB

Combination switch

Condition

Continuity

Terminal

3

4

Front washer switch ON

Existed

1

6

1

4

Rear washer switch ON

6

3