Nissan Juke F15. Manual - part 1265

TM-250

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10B]

P0715 INPUT SPEED SENSOR A

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

Check the following items:

• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-43, "Wiring Dia-

gram - IGNITION POWER SUPPLY -"

.

• Short circuit in harness between IPDM E/R harness connector terminal 57 and primary speed sensor har-

ness connector terminal 3.

• 10A fuse (No.55, located in IPDM E/R). Refer to 

PG-82, "Fuse, Connector and Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace damaged parts.

Primary speed sensor

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

F55

3

E15

57

Existed

P0720 OUTPUT SPEED SENSOR

TM-251

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0720 OUTPUT SPEED SENSOR

DTC Logic

INFOID:0000000012200941

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Start the engine.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “PRI SPEED” and “VEHICLE SPEED”.

4. Drive the vehicle.

5. Maintain the following conditions for 5 seconds or more.

6. Stop the vehicle.

7. Select “Self Diagnostic Results” in “TRANSMISSION”.

With GST

Follow the procedure “With CONSULT”.
Is “P0720” detected?

YES

>> Go to 

TM-251, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012200942

1.

 CHECK SECONDARY SPEED SENSOR POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect secondary speed sensor connector.

3. Turn ignition switch ON.

4. Check voltage between secondary speed sensor harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 5.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0720

Output Speed Sensor Circuit

• Secondary speed sensor signal is not input 

to TCM.

• Secondary pulley speed sensor value is 

less than 150 rpm while primary pulley 
speed is 1,000 rpm or more.

• Harness or connectors

(Sensor circuit is open or shorted.)

• Output speed sensor

PRI SPEED

: 1,000 rpm or more

VEHICLE SPEED

: 10 km/h (7 MPH) or more

+

−

Voltage

Secondary speed sensor

Connector

Terminal

F19

3

Ground

10 V – 16 V

TM-252

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10B]

P0720 OUTPUT SPEED SENSOR

2.

 CHECK TCM INPUT SIGNAL

1. Turn ignition switch OFF.

2. Connect secondary speed sensor connector.

3. Lift up the vehicle.

4. Start the engine.

5. Check frequency of secondary speed sensor.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 3.

3.

 CHECK CIRCUIT BETWEEN TCM AND SECONDARY SPEED SENSOR (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector and secondary speed sensor connector.

3. Check continuity between TCM harness connector terminals and secondary speed sensor harness con-

nector terminals.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

 CHECK CIRCUIT BETWEEN TCM AND SECONDARY SPEED SENSOR (PART 2)

Check continuity between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> Replace secondary speed sensor. Refer to 

TM-337, "Removal and Installation"

.

NO

>> Repair or replace damaged parts.

5.

 CHECK CIRCUIT BETWEEN SECONDARY SPEED SENSOR AND IPDM E/R

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between secondary speed sensor harness connector terminal and IPDM E/R harness

connector terminal.

TCM

Condition

Frequency (Approx.) 

Connector

+

−

Terminal

F81

34

25

• Selector lever: “M

1

” position

• Vehicle speed: 20 km/h (12 MPH) 

480 Hz

JPDIA0901ZZ

TCM

Secondary speed sensor

Continuity

Connector

Terminal

Connector

Terminal

F81

25

F19

1

Existed

34

2

TCM

—

Continuity

Connector

Terminal

F81

25

Ground

Not existed

34

P0720 OUTPUT SPEED SENSOR

TM-253

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

Check the following items:

• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-43, "Wiring Dia-

gram - IGNITION POWER SUPPLY -"

.

• Short circuit in harness between IPDM E/R harness connector terminal 57 and secondary speed sensor har-

ness connector terminal 3.

• 10A fuse (No.55, located in IPDM E/R). Refer to 

PG-82, "Fuse, Connector and Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace damaged parts.

Secondary speed sensor

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

F19

3

E15

57

Existed