Nissan Juke F15. Manual - part 1140

 

  Index      Nissan     Nissan Juke F15 (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1138  1139  1140  1141   ..

 

 

Nissan Juke F15. Manual - part 1140

 

 

SEC-84

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B261F ASCD CLUTCH SWITCH

>> INSPECTION END

B2620 PARK/NEUTRAL POSITION SWITCH

SEC-85

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2620 PARK/NEUTRAL POSITION SWITCH

DTC Logic

INFOID:0000000012202180

NOTE:

• If DTC B2620 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B2620 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Drive vehicle at a speed of 40 km/h (24.8 MPH) or more for 10 seconds.

3. Decrease the vehicle speed to below 40 km/h (24.8 MPH).

4. Repeat steps 2 and 3 twice (a total of 3 times).

5. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES >> Go 

to 

SEC-85, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202181

1.

CHECK DTC OF COMBINATION METER

Check DTC in “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.

Refer to 

MWI-33, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK FUSE

1. Turn power switch OFF.

2. Check that the following fuse in the fuse block (J/B) is not blown.

Is the fuse blown (open)?

YES

>> Replace the blown fuse after repairing the cause of blowing.

NO

>> GO TO 3.

3.

CHECK PARK/NEUTRAL POSITION SWITCH POWER SUPPLY 

1. Turn ignition switch OFF.

2. Disconnect park/neutral position switch connector.

3. Turn ignition switch ON.

4. Check voltage between park/neutral position switch harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detection condition

Possible cause

B2620

NEUTRAL SW

BCM detects the following status for 10 sec-
onds 3 times
• Park/neutral position switch input: Battery 

voltage

• Vehicle speed: 40 km/h (24.8 MPH) or more

• Harness or connector

(CAN communication line is open or 
shorted.)

• Harness or connector

(Park/neutral position switch circuit 
is open or shorted)

• Park/neutral position switch
• Combination meter
• BCM

Signal name

Fuse No.

Ignition power supply

5 (10 A)

SEC-86

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2620 PARK/NEUTRAL POSITION SWITCH

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK PARK/NEUTRAL POSITION SWITCH INPUT SIGNAL 

1. Turn ignition switch OFF.

2. Connect park/neutral position switch connector.

3. Turn ignition switch ON.

4. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> INSPECTION END

6.

CHECK PARK/NEUTRAL POSITION SWITCH SIGNAL CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect park/neutral position switch connector.

3. Disconnect BCM connector.

4. Check continuity between park/neutral position switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK PARK/NEUTRAL POSITION SWITCH

Refer to 

SEC-87, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace park/neutral position switch. Refer to 

TM-24, "Removal and Installation"

.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

(+)

(–)

Voltage (V)

(Approx.)

Park/neutral position switch

Connector

Terminal

F49

2

Ground

Battery voltage

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M70

102

Ground

Shift lever

Neutral position

Battery voltage

Except neutral position 

0

Park/neutral position switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

F49

3

M70

102

Existed

B2620 PARK/NEUTRAL POSITION SWITCH

SEC-87

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Component Inspection

INFOID:0000000012202182

1.

CHECK PARK/NEUTRAL POSITION SWITCH

1. Turn ignition switch OFF.

2. Disconnect park/neutral position switch connector.

3. Check continuity between park/neutral position switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace park/neutral position switch. Refer to 

TM-24, "Removal and Installation"

.

Park/neutral position switch

Condition

Continuity

Terminal

2

3

Shift  lever

Neutral position

Existed

Except neutral position

Not existed

 

 

 

 

 

 

 

Content   ..  1138  1139  1140  1141   ..