Nissan Juke F15. Manual - part 1138

SEC-76

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2604 SHIFT POSITION

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> INSPECTION END

4.

CHECK BCM INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect transmission range switch connector.

3. Disconnect BCM connector.

4. Check continuity between transmission range switch harness connector and BCM harness connector.

5. Check continuity between transmission range switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Transmission range switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

F27

2

M70

102

Existed

Transmission range switch

Ground

Continuity

Connector

Terminal

F27

2

Not existed

B2605 SHIFT POSITION

SEC-77

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2605 SHIFT POSITION

DTC Logic

INFOID:0000000012202169

DTC DETECTION LOGIC

NOTE:

• If DTC B2605 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B2605 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Shift the selector lever to the P position.

2. Turn ignition switch ON and wait 1 second or more.

3. Shift the selector lever to the N position and wait 1 second or more.

4. Shift the selector lever to any position other than P and N, and wait 1 second or more.

5. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-77, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202170

1.

CHECK IPDM E/R INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect BCM connector.

4. Check continuity between IPDM E/R harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

3. Perform DTC CONFIRMATION PROCEDURE for B2605. Refer to 

SEC-77, "DTC Logic"

.

Is DTC B2605 detected again?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2605

PNP/CLUTCH SW

When ignition switch is ON, P/N position 
signal input from transmission range switch 
and P/N position signal input (CAN) from 
IPDM E/R do not match.

• Harness or connectors

(CAN communication line is open or 
shorted.)

• Harness or connectors

(Transmission range switch circuit is 
open or shorted.)

• Transmission range switch
• IPDM E/R
• BCM

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

E15

48

M70

102

Existed

SEC-78

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2608 STARTER RELAY

B2608 STARTER RELAY

DTC Logic

INFOID:0000000012202171

DTC DETECTION LOGIC

NOTE:

• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-83, "DTC Logic"

.

• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-84, "DTC Logic"

.

• If DTC B2608 is displayed with DTC B210D (IPDM E/R), first perform the trouble diagnosis for DTC B210D.

Refer to 

SEC-109, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine.

CVT models

-

Selector lever: In the P position

-

Brake pedal: Depressed

M/T models

-

Shift lever: In the Neutral position

-

Clutch pedal: Depressed

2. Wait 1 second after engine started.

3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-78, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202172

1.

CHECK DTC OF IPDM E/R

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

PCS-24, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK STARTER RELAY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect BCM connector.

4. Check continuity between IPDM E/R harness connector and BCM harness connector.

5. Check continuity between IPDM E/R harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2608

STARTER RELAY

BCM outputs starter relay OFF signal but 
BCM receives starter relay ON signal from 
IPDM E/R (CAN).

• Harness or connectors 

(CAN communication line is open or 
shorted.)

• Harness or connectors 

(Starter relay circuit is open or shorted.)

• IPDM E/R

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

E13

30

M70

97

Existed

B2608 STARTER RELAY

SEC-79

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

REPLACE IPDM E/R

1. Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

2. Perform DTC CONFIRMATION PROCEDURE for DTC B2608. Refer to 

SEC-78, "DTC Logic"

.

Is DTC B2608 detected again?

YES

>> INSPECTION END

NO

>> GO TO 4.

4.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> INSPECTION END

IPDM E/R

Ground

Continuity

Connector

Terminal

E13

30

Not existed