Nissan Juke F15. Manual - part 1131

SEC-48

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

Refer to 

EC-160, "Work Procedure"

.

>> GO TO 7.

7.

PERFORM THROTTLE VALVE CLOSED POSITION LEARNING

Refer to 

EC-161, "Work Procedure"

.

>> GO TO 8.

8.

PERFORM IDLE AIR VOLUME LEARNING

Refer to

EC-162, "Work Procedure"

.

>> GO TO 9.

9.

PERFORM G SENSOR CALIBRATION

Refer to 

EC-164, "Work Procedure"

.

>> END

BCM
BCM : Description

INFOID:0000000012202130

BEFORE REPLACEMENT

When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-

ment. For details, refer to 

SEC-48, "BCM : Work Procedure"

.

NOTE:

If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after

replacing BCM.

AFTER REPLACEMENT

CAUTION:

When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,

BCM control function does not operate normally.

• Complete the procedure of “WRITE CONFIGURATION” in order.

• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.

• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.

NOTE:

When replacing BCM, perform the system initialization (NATS) (if equipped).

BCM : Work Procedure

INFOID:0000000012202131

1.

SAVING VEHICLE SPECIFICATION

CONSULT Configuration

Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to 

BCS-80, "Descrip-

tion"

.

NOTE:

If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after

replacing BCM.

>> GO TO 2.

2.

REPLACE BCM

Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

SEC-49

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

CONSULT Configuration

Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write

vehicle specification. Refer to 

BCS-80, "Work Procedure"

.

>> GO TO 4.

4.

INITIALIZE BCM (NATS) (IF EQUIPPED)

Perform BCM initialization. (NATS)

>> WORK END

SEC-50

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P1610 LOCK MODE

DTC/CIRCUIT DIAGNOSIS

P1610 LOCK MODE

Description

INFOID:0000000012202132

ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times

or more while communication between ECM and BCM is not normal.

DTC Logic

INFOID:0000000012202133

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-50, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202134

1.

CHECK ENGINE START FUNCTION

1. Check that DTC except for DTC P1610 is not detected.

If detected, erase the DTC after fixing.

2. Turn ignition switch OFF.

3. Depress brake pedal and contact the registered Intelligent Key backside to push-button ignition switch,

then wait 5 seconds.

4. Turn ignition switch ON.

5. Turn ignition switch OFF and wait 5 seconds.

6. Repeat steps 3 and 5 twice (a total of 3 times).

7. Check that engine can start.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1610

LOCK MODE

When ECM detects a communication malfunction between 
ECM and BCM 5 times or more.

—

P1611 ID DISCORD, IMMU-ECM

SEC-51

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

P1611 ID DISCORD, IMMU-ECM

DTC Logic

INFOID:0000000012202135

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-51, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012202136

1.

PERFORM INITIALIZATION

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK SELF DIAGNOSTIC RESULT

1. Select “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

2. Erase DTC.

3. Perform DTC CONFIRMATION PROCEDURE for DTC P1611. Refer to 

SEC-51, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

NO

>> GO TO 4.

4.

REPLACE ECM

Replace ECM.

Refer to 

EC-590, "Removal and Installation"

.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1611

ID DISCORD, IMMU-ECM

The ID verification results between BCM 
and ECM are NG.

• BCM
• ECM