Nissan Juke F15. Manual - part 1068

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

PWC-25

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

Description

INFOID:0000000012196909

When the control unit replaced, the initialization in necessary for normal operation of power window system.

Refer to 

PWC-25, "Work Procedure"

.

CAUTION:

The following specified operations cannot be performed under the non-initialized condition.

• Auto-up operation

• Anti-pinch function

Work Procedure

INFOID:0000000012196910

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

PWC-26, "Description"

.

>> GO TO 2.

2.

CHECK ANTI-PINCH FUNCTION

Check anti-pinch function. Refer to 

PWC-27, "Description"

.

>> END

PWC-26

< BASIC INSPECTION >

SYSTEM INITIALIZATION

SYSTEM INITIALIZATION

Description

INFOID:0000000012196911

If any of the following operations are performed, the initialization is necessary for normal operation of power

window system. Refer to 

PWC-26, "Work Procedure"

.

• Disconnection and connection of battery cable from negative terminal.

• When power window main switch replaced.

• Electric power supply to power window main switch or power window motor (driver side) is interrupted by

blown fuse or disconnection and connection of the negative terminal of battery, etc.

• Disconnection and connection of power window main switch harness connector.

• Removal of power window motor (driver side) from regulator assembly.

• Operation of regulator assembly as an independent unit.

• Removal and installation of glass.

• Removal and installation of door glass run.

CAUTION:

The following specified operations cannot be performed under the non-initialized condition.

• Auto-up operation

• Anti-pinch function

Work Procedure

INFOID:0000000012196912

1.

STEP 1

1. Close the door.

2. Turn ignition switch ON.

3. Operate power window switch to fully open the window. (This operation is unnecessary if the window is

already fully open)

4. Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed

position, keep pulling the switch for 2 seconds or more.

5. Check that AUTO-UP function operates normally.

>> GO TO 2.

2.

STEP 2

Check anti-pinch function. Refer to 

PWC-27, "Description"

.

>> END

CHECK ANTI-PINCH FUNCTION

PWC-27

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

CHECK ANTI-PINCH FUNCTION

Description

INFOID:0000000012196913

If any of the following operations are performed, the initialization is necessary for normal operation of anti-

pinch function. Refer to 

PWC-27, "Work Procedure"

.

• Disconnection and connection of battery cable from negative terminal.

• When power window main switch replaced.

• Electric power supply to power window main switch or power window motor (driver side) is interrupted by

blown fuse or disconnection and connection of the negative terminal of battery, etc.

• Disconnection and connection of power window main switch harness connector.

• Removal of power window motor (driver side) from regulator assembly.

• Operation of regulator assembly as an independent unit.

• Removal and installation of glass.

• Removal and installation of door glass run.

Work Procedure

INFOID:0000000012196914

1.

CHECK ANTI-PINCH FUNCTION

1. Close the door.

2. Fully open the door window.

3. Place a piece of wood near fully closed position.

4. Close door glass completely with AUTO-UP.

5. Check the following conditions.

-

Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.

-

Check that glass does not rise not when operating the power window main switch while lowering.

CAUTION:

•

Perform initial setting when AUTO-UP operation or anti-pinch function does not operate nor-

mally.

•

Check that AUTO-UP operates before inspection when system initialization is performed.

•

Do not check with hands and other body parts because they may be pinched. Do not get

pinched.

>> END

PWC-28

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

DTC/CIRCUIT DIAGNOSIS

POWER SUPPLY AND GROUND CIRCUIT

POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Diagnosis Procedure

INFOID:0000000012196915

1.

CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check voltage between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between BCM harness connector and power window main switch harness connector.

4. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace harness.

3.

CHECK POWER WINDOW MAIN SWITCH GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace harness.

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

(+)

(-)

Condition

Voltage (V)

Power window main switch

Connector

Terminal 

D35

10

Ground

Ignition switch

ON

9 – 16

D36

18

OFF

BCM

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

M69

68

D35

10

Existed

69

D36

18

BCM

Ground

Continuity

Connector

Terminal

M69

68

Not existed

69

Power window main switch 

Ground

Continuity 

Connector

Terminal

D35

1

Existed