Nissan Juke F15. Manual - part 69

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-31

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

*

1

: It is displayed but does not operate on CVT models.

*

2

: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

UNLK SEN -DR

Indicates [On/Off] condition of driver door UNLOCK status

PUSH SW -IPDM

Indicates [On/Off] condition of push-button ignition switch

IGN RLY1 -F/B

Indicates [On/Off] condition of ignition relay 1

DETE SW -IPDM

Indicates [On/Off] condition of P position

SFT PN -IPDM

Indicates [On/Off] condition of P or N position

SFT P -MET

Indicates [On/Off] condition of P position

SFT N -MET

Indicates [On/Off] condition of N position

ENGINE STATE

Indicates [Stop/Stall/Crank/Run] condition of engine states

S/L LOCK-IPDM

NOTE:
This item is displayed, but cannot be monitored

S/L UNLK-IPDM

NOTE:
This item is displayed, but cannot be monitored

S/L RELAY-REQ

NOTE:
This item is displayed, but cannot be monitored

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h]

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status

ID OK FLAG

Indicates [Set/Reset] condition of key ID

PRMT ENG STRT

Indicates [Set/Reset] condition of engine start possibility

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

RKE-PANIC

Indicates [On/Off] condition of PANIC button of Intelligent Key

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored

Monitor Item

Condition

Test item

Description

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation

INSIDE BUZZER

This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT screen is touched
• Key: Key warning chime sounds when CONSULT screen is touched
• Knob: OFF position warning chime sounds when CONSULT screen is touched
• Off: Non-operation

BCS-32

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)

INFOID:0000000012200709

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

INDICATOR

This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

LCD

This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT screen is touched
• NO KY: Key warning lamp indicator when CONSULT screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT screen is touched
• LK WN: Engine start operation indicator lamp indicate when CONSULT screen is touched

FLASHER

This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched

HORN

This test is able to check horn operation
The horn is activated after “ON” on CONSULT screen is touched

P RANGE

This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched

PUSH SWITCH INDICATOR

This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.

TRUNK/BACK DOOR

This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT screen is touched.

Test item

Description

Monitor item [UNIT]

Description

FR WIPER HI
[Off/On]

Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER LOW
[Off/On]

Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination 
switch reading function.

FR WASHER SW
[Off/On]

Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER INT
[Off/On]

Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination 
switch reading function.

INT VOLUME
[1 - 7]

Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.

TURN SIGNAL R
[Off/On]

Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch 
reading function.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-33

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM
BCM : CONSULT Function (BCM - BCM)

INFOID:0000000012200710

WORK SUPPORT

IMMU
IMMU : CONSULT Function (BCM - IMMU)

INFOID:0000000012965018

WORK SUPPORT

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

TURN SIGNAL L
[Off/On]

Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch 
reading function.

TAIL LAMP SW
[Off/On]

Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination 
switch reading function.

HI BEAM SW
[Off/On]

Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch 
reading function.

HEAD LAMP SW 1
[Off/On]

Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination 
switch reading function.

HEAD LAMP SW 2
[Off/On]

Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination 
switch reading function.

PASSING SW
[Off/On]

Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch 
reading function.

AUTO LIGHT SW
[Off/On]

Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination 
switch reading function.

FR FOG SW
[Off/On]

Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch 
reading function.

Monitor item [UNIT]

Description

Item

Description

RESET SETTING VALUE

Return a value set with Work Support of each system to a default value in factory shipment.

Service item

Description

CONFIRM DONGLE ID

It is possible to check that dongle unit is applied to the vehicle.

Monitor item 

Content

CONFRM ID ALL

Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.

CONFIRM ID4

CONFIRM ID3

CONFIRM ID2

CONFIRM ID1

NOT REGISTERED

Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.

TP 4

Indicates the number of IDs that are registered.

TP 3

TP 2

TP 1

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

BCS-34

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)

INFOID:0000000012965032

WORK SUPPORT

*:Factory setting

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable

to this vehicle, refer to CONSULT display items.

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.

Service item

Setting item

Setting

ROOM LAMP TIMER SET

MODE 1

30 min.

Sets the interior room lamp battery saver timer operating 
time.
NOTE:
The factor setting is 10 minutes. The setting cannot be re-
turned to the factory setting, when the setting is changed 
once.

MODE 2

60 min.

MODE 3

15 min.

BATTERY SAVER SET

On

*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

IGN BATTERY SAVER SET

MODE 1

Without

Sets the ignition battery saver timer operating time.

MODE 2

30 min.

MODE 3*

10 min.

MODE 4

5 min.

MODE 5

60 min.

ACC BATTERY SAVER SET

MODE 1

Without

Sets the accessory battery saver timer operating time.

MODE 2*

30 min.

MODE 3

10 min.

MODE 4

5 min.

MODE 5

60 min.

Monitor item

[Unit]

Description

REQ SW-DR
[On/Off]

Indicated [On/Off] condition of door request switch (driver side)

REQ SW-AS
[On/Off]

Indicated [On/Off] condition of door request switch (passenger side)

REQ SW-RR
[On/Off]

NOTE:
This item is displayed, but cannot be monitored

REQ SW-RL
[On/Off]

NOTE:
This item is displayed, but cannot be monitored

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

UNLK SEN -DR
[On/Off]

Indicates [On/Off] condition of driver door UNLOCK status

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)