Nissan Tiida C11. Manual - part 784

 

  Главная      Nissan     Nissan Tiida C11 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  782  783  784  785   ..

 

 

Nissan Tiida C11. Manual - part 784

 

 

FAX-1

TRANSMISSION & DRIVELINE

C

E

F

G

H

I

J

K

L

M

SECTION 

FAX

A

B

FAX

N

O

P

CONTENTS

FRONT AXLE

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Caution ......................................................................

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Special Service Tool  .................................................

3

Commercial Service Tool  ..........................................

3

SYMPTOM DIAGNOSIS  ...............................

4

NOISE, VIBRATION AND HARSHNESS 
(NVH) TROUBLESHOOTING  .............................

4

NVH Troubleshooting Chart  ......................................

4

ON-VEHICLE MAINTENANCE .....................

5

FRONT WHEEL HUB AND KNUCKLE  ..............

5

On-Vehicle Inspection and Service  ...........................

5

FRONT DRIVE SHAFT ........................................

6

On-Vehicle Inspection and Service  ...........................

6

REMOVAL AND INSTALLATION  ................

7

FRONT WHEEL HUB AND KNUCKLE  .............

7

Removal and Installation  ..........................................

7

FRONT DRIVE SHAFT  .....................................

10

Removal and Installation (Left Side) ........................

10

Removal and Installation (Right Side)  .....................

11

DISASSEMBLY AND ASSEMBLY ..............

14

FRONT DRIVE SHAFT  .....................................

14

Disassembly and Assembly (Left Side)  ...................

14

Disassembly and Assembly (Right Side) .................

19

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

26

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

26

Drive Shaft ...............................................................

26

Dynamic Damper .....................................................

26

FAX-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Caution

INFOID:0000000001716781

Observe the following precautions when disassembling and assembling drive shaft.
• Joint sub-assembly does not disassemble because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Before disassembling and assembling, clean the outside of parts.
• Prevention of the entry of foreign objects must be taken into account during disassembly of the service loca-

tion.

• Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean cover

must be placed over parts.

• Paper shop cloths must be used. Fabric shop cloths must not be used because of danger of lint adhering to

parts.

• Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by

blowing with air or wiping with paper shop cloths.

PREPARATION

FAX-3

< PREPARATION >

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000001716782

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tool

INFOID:0000000001716783

Tool number 
(Kent-Moore No.)
Tool name

Description

KV40107300
(

)

Boot Band crimping tool

Installing boot bands

KV38105500
(J-33904)
Differential side oil seal protector

Installing drive shaft LH
a: 40 mm (1.57 in) dia.

KV38106700
(J-34296)
Differential side oil seal protector

Installing drive shaft RH
a: 36 mm (1.42 in) dia. 

HT72520000
(J-25730-A)
Ball joint remover

Removing tie-rod outer end and lower ball 
joint

ZZA1229D

ZZA0835D

ZZA0835D

NT146

Tool name

Description

Power tool

• Removing wheel nuts
• Removing torque member bolts
• Removing hub lock nut

PBIC0190E

FAX-4

< SYMPTOM DIAGNOSIS >

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

SYMPTOM DIAGNOSIS

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000001716784

Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.

×

: Applicable

Reference page

FA

X

-5

FA

X

-5

FSU-5,

 "

NVH T

ro

u

b

les

h

oot

in

g Ch

art

"

Re

fe

to

 Fro

n

t axle in thi

s

 ch

art.

WT

-4, "

NVH T

rou

bl

es

ho

oti

n

g

 Cha

rt

"

WT

-4, "

NVH T

rou

bl

es

ho

oti

n

g

 Cha

rt

"

Refe

r to

 DRIVE 

SHAFT i

n

 thi

s

 cha

rt.

BR-5,

 "

NVH T

ro

u

b

les

ho

ot

ing

 Ch

art

"

ST

-5

, "

NVH T

rou

bl

es

ho

ot

in

g

 Cha

rt

"

Possible cause and SUSPECTED PARTS

Ex

ce

ss

iv

e joi

n

an

gl

e

Jo

in

t sl

id

in

g

 re

si

st

a

n

c

e

Im

ba

la

nc

e

Im

p

rop

er i

n

s

ta

lla

ti

o

n

, lo

os

en

es

s

Part

s interf

erence

Whe

e

l be

ari

n

g

 da

ma

ge

FRONT S

U

SPENSION

FRONT A

X

LE

TI

RE

S

ROAD WHEE

LS

DRIVE SHAFT

BRAKE

S

STE

E

RING

Symptom

DRIVE 
SHAFT

Noise

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

FRONT 
AXLE

Noise

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

Vibration

×

×

×

×

×

×

×

Shimmy

×

×

×

×

×

×

×

Shudder

×

×

×

×

×

×

Poor quality ride or handling

×

×

×

×

×

 

 

 

 

 

 

 

содержание   ..  782  783  784  785   ..