Nissan Tiida C11. Manual - part 98

BRC-158

< COMPONENT DIAGNOSIS >

[ESP/TCS/ABS]

VDC OFF INDICATOR LAMP

VDC OFF INDICATOR LAMP

Description

INFOID:0000000001731190

×

: ON –: OFF

Component Function Check

INFOID:0000000001731191

1.

VDC OFF INDICATOR LAMP OPERATION CHECK 1

Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.
Is the inspection result normal?

YES

>> GO TO 2

NO

>> Go to diagnosis procedure. Refer to 

BRC-158, "Diagnosis Procedure"

.

2.

VDC OFF INDICATOR LAMP OPERATION CHECK 2

Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check VDC OFF switch. Refer to 

BRC-154, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000001731192

1.

CHECK VDC OFF SWITCH

Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?

YES

>> GO TO 2

NO

>> Check VDC OFF switch. Refer to 

BRC-154, "Diagnosis Procedure"

.

2.

CHECK SELF-DIAGNOSIS

Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to 

BRC-25, "CONSULT-III Function

(ABS)"

.

Is the inspection result normal?

YES

>> GO TO 3

NO

>> Check items displayed by self-diagnosis.

3.

CHECK COMBINATION METER

Check if the indication and operation of combination meter are normal. Refer to 

MWI-21, "Diagnosis Descrip-

tion"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-184, "Removal and Installa-

tion"

.

NO

>> Replace combination meter. Refer to 

MWI-94, "Removal and Installation"

.

Condition

VDC OFF indicator lamp

Ignition switch OFF

–

For 1 second after turning ON ignition switch

×

1 second later after turning ON ignition switch

–

VDC OFF switch turned ON. (VDC function is OFF.)

×

VDC/TCS function is malfunctioning.

×

ABS function is malfunctioning.

×

EBD function is malfunctioning.

×

SLIP INDICATOR LAMP

BRC-159

< COMPONENT DIAGNOSIS >

[ESP/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

SLIP INDICATOR LAMP

Description

INFOID:0000000001731193

×

: ON –: OFF

Component Function Check

INFOID:0000000001731194

1.

CHECK SLIP INDICATOR LAMP OPERATION

Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to diagnosis procedure. Refer to 

BRC-159, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000001731195

1.

CHECK SELF-DIAGNOSIS

Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to 

BRC-25, "CONSULT-III Function

(ABS)"

.

Is the inspection result normal?

YES

>> GO TO 2

NO

>> Check items displayed by self-diagnosis.

2.

CHECK COMBINATION METER

Check if the indication and operation of combination meter are normal. Refer to 

MWI-21, "Diagnosis Descrip-

tion"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-184, "Removal and Installa-

tion"

.

NO

>> Replace combination meter. Refer to 

MWI-94, "Removal and Installation"

.

Condition

SLIP indicator lamp

Ignition switch OFF

–

For 1 second after turning ON ignition switch

×

1 second later after turning ON ignition switch

–

VDC/TCS function is malfunctioning.

×

ABS function is malfunctioning.

×

EBD function is malfunctioning.

×

BRC-160

< ECU DIAGNOSIS >

[ESP/TCS/ABS]

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

ECU DIAGNOSIS

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Reference Value

INFOID:0000000001731196

VALUES ON THE DIAGNOSIS TOOL

CAUTION:

The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.

CONSULT-III MONITOR ITEM

 Monitor item

Display content

Data monitor

Condition

Reference value in 

normal operation

FR LH SENSOR

Wheel speed

0 [km/h (MPH)]

Vehicle stopped

Nearly matches the speed meter display 
(

±

 10% or less)

Vehicle running 

(Note 1)

FR RH SENSOR

Wheel speed

0 [km/h (MPH)]

Vehicle stopped

Nearly matches the speed meter display 
(

±

 10% or less)

Vehicle running 

(Note 1)

RR LH SENSOR

Wheel speed

0 [km/h (MPH)]

Vehicle stopped

Nearly matches the speed meter display 
(

±

 10% or less)

Vehicle running 

(Note 1)

RR RH SENSOR

Wheel speed

0 [km/h (MPH)]

Vehicle stopped

Nearly matches the speed meter display 
(

±

 10% or less)

Vehicle running 

(Note 1)

STOP LAMP SW

Stop lamp switch signal status

When brake pedal is depressed

ON

When brake pedal is released

OFF

BATTERY VOLT

Battery voltage supplied to the ABS actuator 
and electric unit (control unit)

Ignition switch ON

10 – 16 V

GEAR

Gear position determined by TCM

1st gear 
2nd gear
3rd gear
4th gear
5th gear

1
2
3
4
5

 SLCT LVR POSI

A/T selector lever position

P position
R position
N position
D position

P
R
N
D

OFF SW

VDC OFF switch ON/OFF

VDC OFF switch ON
(When VDC OFF indicator lamp is ON)

ON

VDC OFF switch OFF
(When VDC OFF indicator lamp is OFF)

OFF

YAW RATE SEN

Yaw rate detected by yaw rate/side/decel G 
sensor

When vehicle is stopped

Approx. 0 d/s

When vehicle turning

−

75 to 75 d/s

ACCEL POS SIG 

Throttle actuator opening/closing is dis-
played (linked with accelerator pedal)

Accelerator pedal not depressed (ignition 
switch is ON)

0 %

Accelerator pedal depressed (ignition 
switch is ON)

0 - 100 %

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

BRC-161

< ECU DIAGNOSIS >

[ESP/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

SIDE G-SENSOR

Transverse G detected by side G sensor

Vehicle stopped

Approx. 0 m/s

2

Vehicle turning right

Negative value 

(m/s

2

)

Vehicle turning left

Positive value

(m/s

2

)

STR ANGLE SIG

Steering angle detected by steering angle 
sensor

Straight-ahead

Approx. 0

°

Steering wheel turned

–720 to 720

°

 

PRESS SENSOR

Brake fluid pressure detected by front pres-
sure sensor

With ignition switch turned ON and brake 
pedal released

Approx. 0 bar

With ignition switch turned ON and brake 
pedal depressed

–40 to 300 bar

ENGINE SPEED

With engine running

With engine stopped

0 rpm

Engine running

Almost in accor-
dance with tachome-
ter display

FLUID LEV SW

Brake fluid level switch signal status

When brake fluid level switch ON

ON

When brake fluid level switch OFF 

OFF

FR RH IN SOL

Operation status of each solenoid valve 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)

ON

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

OFF

FR RH OUT SOL

Operation status of each solenoid valve 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)

ON

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

OFF

FR LH IN SOL

Operation status of each solenoid valve 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)

ON

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

OFF

FR LH OUT SOL

Operation status of each solenoid valve 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)

ON

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

OFF

RR RH IN SOL

Operation status of each solenoid valve 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)

ON

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

OFF

 Monitor item

Display content

Data monitor

Condition

Reference value in 

normal operation