Content      ..     16      17      18      19     ..

Mitsubishi Outlander (2022 year). Manual in english - page 18

Control System (ACC) with Stop & Go” (P.5-

The Lane Keep Assist (LKA) only steers

103).

the vehicle to maintain its position in the

center of a lane. The vehicle will not steer

The Lane Keep Assist (LKA) can be activated

to avoid objects in the road in front of the

when the following conditions are met:

vehicle or to avoid a vehicle moving into

your lane.

The ACC system is activated.

Lane markers on both sides are clearly

It is the driver’s responsibility to stay alert,

drive safely, keep the vehicle in the

detected.

traveling lane, and be in control of the

A vehicle ahead is detected

(when the

vehicle at all times. Never take your hands

vehicle is driven at speeds under 37 MPH

off the steering wheel when driving. Al-

(60 km/h)).

ways keep your hands on the steering

The driver grips the steering wheel.

wheel and drive your vehicle safely.

The vehicle is driven at the center of the

Always drive carefully and attentively

lane.

when using the Lane Keep Assist (LKA).

WAF0620X

The turn signals are not operated.

Example

thoroughly before using the Lane Keep

The windshield wiper is not operated in the

Assist (LKA). To avoid serious injury or

Lane Keep Assist (LKA) display and

high speed position (the Lane Keep Assist

death, do not rely on the system to prevent

(LKA) function is disabled after the wiper

indicators

accidents or to control the vehicle’s speed

operates for approximately 10 seconds in

1. Lane Keep Assist (LKA) status indicator/

in emergency situations. Do not use the

the high speed position).

warning

Lane Keep Assist (LKA) except in appro-

priate road and traffic conditions.

To

enable or disable the Lane Keep Assist

Displays the status of the Lane Keep Assist

(LKA), see “How to enable/disable the Lane

(LKA) by the color of the indicator/warning

Keep Assist (LKA)” (P.5-102).

Lane Keep Assist (LKA) operation

. Lane Keep Assist (LKA) status indicator

(gray): Lane Keep Assist (LKA) standby

The Lane Keep Assist (LKA) helps the driver

. Lane Keep Assist (LKA) status indicator

keep the vehicle near the center of the lane

(green): Lane Keep Assist (LKA) active

when both right and left lane markers are

. Lane Keep Assist (LKA) status indicator

detected. The Lane Keep Assist (LKA) only

(orange): Lane Keep Assist

(LKA)

operates when combined with the Adaptive

malfunction

Cruise Control System

(ACC) system. For

additional information, see

“Adaptive Cruise

5-118

Starting and driving

2.

Lane Keep Assist (LKA) indicator

operation, the Lane Keep Assist (LKA) status

indicator

, the Lane Keep Assist

(LKA)

Indicates the status of the Lane Keep Assist

indicator

, and the lane marker indicator

(LKA) by the color of the indicator

and

on the multi-information display turn

. Lane Keep Assist

(LKA) indicator

green. A chime sounds when the Lane Keep

(gray): Lane Keep Assist (LKA) standby

Assist (LKA) initially activates.

. Lane Keep Assist

(LKA) indicator

(green): Lane Keep Assist (LKA) active

When the Lane Keep Assist (LKA) deactivates,

the Lane Keep Assist (LKA) status indicator

,

3.

Lane marker indicator

the Lane Keep Assist (LKA) indicator

, and

Indicates whether the system detects the

the lane marker indicator and on the multi-

lane marker

information display turn gray and a chime

. Lane marker indicator

(gray): Lane

sounds twice.

markers not detected

. Lane marker indicator

(green): Lane

Lane Departure Prevention (LDP)

WAF0711X

markers detected

With the Lane Keep Assist (LKA) active, when

. Lane marker indicator

(orange): Lane

a curve or strong cross wind exceeds the

Hands on detection

departure is detected

capabilities of the system and your vehicle

When the Lane Keep Assist (LKA) is activated,

approaches either the left or the right side of the

4.

Lane marker indicator/speed control

it monitors the driver’s steering wheel opera-

status indicator/set distance indicator

traveling lane, the LDP system will flash the

tion.

LDP indicator on the multi-information display

Displays the status of the Lane Keep Assist

If the steering wheel is not operated or the

and provide steering wheel vibration to alert the

(LKA) by the color of the lane marker

driver takes his/her hands off the steering wheel

driver. The warning chime will also sound (4

indicator.

for a period of time, the warning

appears in

rapid beeps). Then, the LDP system automati-

. Lane marker indicator (gray): Lane Keep

the multi-information display and the hands

cally applies the brakes for a short period of

Assist (LKA) standby

OFF warning light illuminates.

time to help assist the driver to return the

. Lane marker indicator

(green): Lane

vehicle to the center of the traveling lane. This

If the driver does not operate the steering wheel

Keep Assist (LKA) active

action is in addition to any Lane Keep Assist

after the warning has been displayed and the

For the speed control status indicator and set

(LKA) actions and the warnings cannot be

warning light illuminated, an audible alert

distance indicator, see “MI-PILOT Assist sys-

turned off. For more information, see “Lane

sounds and both the warning and the warning

tem display and indicators” (P.5-95).

Departure Prevention (LDP)” (P.5-38).

light flash. If the driver still does not operate the

When the Lane Keep Assist

(LKA) is in

steering wheel, the system applies a momentary

Starting and driving

5-119

brake application to request the driver to take

Lane Keep Assist (LKA) limitations

Lane Keep Assist

(LKA) could

control of the vehicle again.

detect these items as lane mar-

If the driver still does not respond, the system

kers)

WARNING

turns on the hazard flasher and slows the

— When driving on roads where the

vehicle to a complete stop.

In the following situations, the camera may

traveling lane merges or separates

The driver can cancel the deceleration at any

not detect lane markers correctly or may

Do not use the Lane Keep Assist (LKA)

time by steering, braking, accelerating, or

detect lane markers incorrectly and the

under the following conditions because the

operating the MI-PILOT Assist switch.

Lane Keep Assist (LKA) may not operate

system may not properly detect lane

properly:

markers. Doing so could cause a loss of

— When driving on roads where

vehicle control and result in an accident.

WARNING

there are multiple parallel lane

— During bad weather (rain, fog,

markers, lane markers that are

snow, dust, etc.)

Lane Keep Assist (LKA) is not a system for a

faded or not painted clearly, non-

hands-free driving. Always keep your hands on

— When rain, snow, sand, etc., is

the steering wheel and drive your vehicle

standard lane markers, or lane

thrown up by the wheels of other

safely. Failure to do so could cause a collision

markers covered with water, dirt,

vehicles

resulting in serious personal injury or death.

snow, etc.

— When dirt, oil, ice, snow, water, or

— When driving on roads with

NOTE:

another object adheres to the

discontinued lane markers

camera unit

If the driver lightly touches (instead of firmly

— When driving on roads with a

grips) the steering wheel, the steering torque

— When the lens of the camera unit

widening or narrowing lane width

sensor may not detect the driver’s hand(s) on

is foggy

the steering wheel and a sequence of warn-

— When driving on roads where

— When strong light (for example,

ings may occur. When the driver holds and

there are multiple lanes or un-

sunlight or high beams from

operates the steering wheel again, the warn-

clear lane markers due to road

oncoming vehicles) shines on the

ings turn off.

construction

camera

— When driving on roads where

— When the headlights are not

there are sharply contrasting ob-

bright due to dirt on the lens or

jects, such as shadows, snow,

the headlights are off in tunnels or

water, wheel ruts, seams, or lines

darkness

remaining after road repairs (the

5-120

Starting and driving

Do not use the conventional (fixed speed)

cruise control mode when driving under

the following conditions:

— When it is not possible to keep the

vehicle at a set speed

— In heavy traffic or in traffic that

varies in speed

— On winding or hilly roads

— On slippery roads (rain, snow, ice,

etc.)

— In very windy areas

Doing so could cause

a loss of

vehicle

WAF0712X

WAF0660X

control and result in an accident.

Conventional (fixed speed) cruise

Conventional (fixed speed) cruise

control switches

control mode display and indicators

1. RES+ switch:

The display is located in the multi-information

display.

Resumes set vehicle speed or increases

speed incrementally

1. Cruise indicator:

2. SET- switch:

This indicator indicates the condition of the

ACC system depending on a color.

Sets desired cruise speed or reduces speed

incrementally

. Cruise control ON indicator

(gray):

Indicates that the MI-PILOT Assist

3. CANCEL switch:

switch is on

Deactivates the system without erasing the

. Cruise control SET indicator

(green):

set vehicle speed

Indicates that the cruising speed is set

4. MI-PILOT Assist switch:

. Cruise control warning

(orange): Indi-

Turns the MI-PILOT Assist system on or off

cates that there is a malfunction in the

Starting and driving

5-123

ACC system

system completely off. When the ignition

switch is placed in the OFF position, the system

2. Set vehicle speed indicator:

is also automatically turned off.

This indicator indicates the set vehicle

To use the ACC system again, quickly push and

speed.

release the MI-PILOT Assist switch (vehicle-to-

For Canadian models, the speed is displayed

vehicle distance control mode) or push and hold

in km/h.

it

(conventional cruise control mode) again to

turn it on.

WARNING

To avoid accidentally engaging cruise control,

make sure to turn the MI-PILOT Assist switch

WAF0713X

off when not using the ACC system.

Operating conventional (fixed speed)

cruise control mode

To turn on the conventional (fixed speed) cruise

control mode, push and hold the MI-PILOT

Assist switch

for longer than about

1.5

seconds.

When pushing the MI-PILOT Assist switch on,

the conventional

(fixed speed) cruise control

mode display and indicators are displayed in the

multi-information display. After you hold the

MI-PILOT Assist switch on for longer than

about

1.5

seconds, the ACC system display

turns off. The cruise indicator appears. You can

now set your desired cruising speed. Pushing

the MI-PILOT Assist switch again will turn the

5-124

Starting and driving

1. Push the CANCEL switch. The set vehicle

3. Push down, then quickly release the SET-

speed indicator will turn off.

switch. Each time you do this, the set

vehicle speed will decrease by about 1 MPH

2. Tap the brake pedal. The set vehicle speed

(1 km/h).

indicator will turn off.

To resume the preset vehicle speed, push up and

3. Turn the MI-PILOT Assist switch off. Both

the cruise indicator and set vehicle speed

release

the RES+ switch. The vehicle will

indicator will turn off.

resume

the last

set cruising speed when

the

vehicle speed is over

20

MPH (30

km/h).

To reset at a faster cruising speed, use one of the

following three methods:

1. Depress the accelerator pedal. When the

vehicle attains the desired speed, push down

and release the SET- switch.

WAF0714X

2. Push up and hold the RES+ switch. When

the vehicle attains the desired speed, release

To set cruising speed, accelerate your vehicle to

the switch.

the desired speed, push down the SET- switch

3. Push up, then quickly release the RES+

and release it. (The color of the cruise indicator

switch. Each time you do this, the set

changes to green and set vehicle speed indicator

vehicle speed will increase by about 1 MPH

comes on.) Take your foot off the accelerator

(1 km/h).

pedal. Your vehicle will maintain the set speed.

To reset at a slower cruising speed, use one of

. To pass another vehicle, depress the accel-

the following three methods:

erator pedal. When you release the pedal,

the vehicle will return to the previously set

1. Lightly tap the brake pedal. When the

speed.

vehicle attains the desired speed, push down

. The vehicle may not maintain the set speed

the SET- switch and release it.

when going up or down steep hills. If this

2. Push down and hold the SET- switch.

happens, manually maintain vehicle speed.

Release the switch when the vehicle slows

To cancel the preset vehicle speed, use any of

down to the desired speed.

the following methods:

Starting and driving

5-125

FORWARD COLLISION

MITIGATION SYSTEM (FCM)

WARNING

Failure to follow the warnings and instructions

for proper use of the FCM system could result

in serious injury or death.

. The FCM system is a supplemental aid to

the driver. It is not a replacement for the

driver’s attention to traffic conditions or

responsibility to drive safely. It cannot

prevent accidents due to carelessness or

dangerous driving techniques.

. The FCM system does not function in all

driving, traffic, weather and road condi-

WAF0392X

tions.

The FCM system uses a radar sensor located

The FCM system can assist the driver when

on the front of the vehicle to measure the

there is a risk of a forward collision with the

distance to the vehicle ahead in the same lane.

vehicle ahead in the traveling lane or with a

For pedestrians, the FCM system uses a camera

pedestrian.

installed behind the windshield in addition to

the radar sensor.

5-126

Starting and driving

If a risk of a forward collision is detected, the

FCM system will firstly provide the warning to

the driver by flashing the vehicle ahead

detection indicator (yellow) in the multi-infor-

mation display and providing an audible alert.

In addition, the system applies partial braking.

If the driver applies the brakes quickly and

forcefully after the warning, and the FCM

system detects that there is still the possibility

of a forward collision, the system will auto-

matically increase the braking force.

If the driver does not take action, the FCM

system provide the warning to the driver by

flashing FCM emergency warning indicator

(red) in the multi-information display and

providing an audible alert. Then the system

applies partial braking.

If the risk of a collision becomes imminent, the

FCM system applies harder braking automati-

cally.

While the FCM system is operating, you may

WAF0622X

hear the sound of brake operation. This is

normal and indicates that the FCM system is

FCM emergency warning indicator

FCM SYSTEM OPERATION

operating properly.

Vehicle ahead detection indicator (on the multi-

information display)

The FCM system will function when your

NOTE:

vehicle is driven at speeds above approximately

FCM system OFF warning light (on the meter

The vehicle’s stop lights come on when

3 MPH (5 km/h).

panel)

braking is performed by the FCM system.

Steering wheel remote control switches

(left

For the pedestrian detection function, the FCM

Depending on vehicle speed and distance to the

side)

system operates at speeds between 6 - 37 MPH

vehicle or pedestrian ahead, as well as driving

(10 - 60 km/h).

Starting and driving

5-127

and roadway conditions, the system may help

the driver avoid a forward collision or may help

mitigate the consequences of a collision should

one be unavoidable.

If the driver is handling the steering wheel,

accelerating or braking, the FCM system will

function later or will not function.

The automatic braking will cease under the

following conditions:

. When the steering wheel is turned as far as

necessary to avoid a collision.

. When the accelerator pedal is depressed.

. When there is no longer a vehicle or

pedestrian detected ahead.

If the FCM system has stopped the vehicle, the

vehicle will remain at a standstill for approxi-

mately 2 seconds before the brakes are released.

When the brake pedal is depressed while the

brake is applied by the system, you may feel the

pedal effort is changed and may hear a sound

and vibration noise. This is normal and does not

WAF0623X

indicate a malfunction. In addition, the braking

force can be increased by adding the pedal

FCM system OFF warning light (on the meter

TURNING THE FCM SYSTEM

effort.

panel)

Steering wheel remote control switches

(left

ON/OFF

side)

Perform the following steps to

turn the FCM

Multi-information display

system on or off.

1. Press the

button until “Settings”

appears in the multi-information display

5-128

Starting and driving

sensor areas covered by ice, snow or

— cyclists

stickers, for example. In these cases, the

system may not be able to warn the driver

— objects on the road (such as trees)

properly. Be sure that you check, clean and

Braking distances increase on slippery

clear sensor areas regularly.

surfaces.

In some road and traffic conditions, the

Do not use the FCM system if you are

FCM system may unexpectedly apply

towing a trailer. The system may not detect

partial braking. When acceleration is

a vehicle ahead.

necessary, depress the accelerator pedal

to override the system.

Do not use the FCM system when driving

with a tire that is not within normal tire

The FCM system may operate when a

conditions (for example, tire wear, low tire

pattern, object, shadow or lights are

pressure, installation of tire chains, non-

detected that are similar to the outline of

standard wheels).

vehicles or pedestrians, or if they are the

same size and position as a vehicle or

Excessive noise will interfere with

the

motorcycle’s tail lights.

warning chime sound, and the chime may

— objects above road (low bridge,

not be heard.

The system may keep operating when the

traffic sign, etc.)

vehicle ahead is turning right or left.

— objects on the road surface (rail-

The system may operate when your vehicle

road track, grate, steel plate, etc.)

is approaching and passing a vehicle

ahead.

— objects in the parking garage

(beam, pillar, etc.)

Depending on the road shape

(curved

road, entrance and exit of the curve,

— pedestrians, cyclists or motor-

winding road, lane regulation, under con-

cycles approaching the traveling

struction, etc.), the system may operate

lane

temporarily for the oncoming vehicle in

front of your vehicle.

— vehicles, pedestrians, cyclists, mo-

The FCM system may react to:

torcycles or objects in adjacent

lane or close to the vehicle

— objects on the roadside (traffic

sign, guardrail, pedestrian, cy-

— oncoming pedestrians

clist, motorcycle, vehicle, etc.)

Starting and driving

5-131

. The camera unit detects it’s misalignment

condition.

. The radar sensor picks up interference from

an another radar source.

Action to take:

When the above conditions no longer exist, the

FCM system will resume automatically.

NOTE:

When the inside of the windshield on camera

area is misted or frozen, it will take a period

of time to remove it after air conditioner

turns on. If dirt appears on this area, it is

recommended you visit an authorized

SSD0253

Mitsubishi Motors dealer.

When driving on some roads, such as winding,

SYSTEM TEMPORARILY UN-

Condition B

hilly, curved, narrow roads, or roads which are

AVAILABLE

In the following condition, the FCM system

under construction or on a slope, the sensor may

OFF warning light will flash and the “Forward

detect vehicles in a different lane, or may

Condition A

Driving Aids temporarily disabled Front Sensor

temporarily not detect a vehicle traveling ahead.

If the following conditions, the FCM

system

blocked” warning message will appear in the

This may cause the system to work inappropri-

OFF warning light will blink

(no message

multi-information display.

ately.

appears in the multi-information display).

. The sensor area of the front of the vehicle is

The detection of vehicles may also be affected

. Strong light is shining from the front of the

covered with dirt or is obstructed

by vehicle operation

(steering maneuver or

vehicle.

Action to take:

traveling position in the lane, etc.) or vehicle

. The cabin temperature is over approxi-

condition. If this occurs, the system may warn

If the warning light flashes, stop the vehicle in a

mately 104°F (40°C) in direct sunlight.

you by blinking the system indicator and

safe place and turn the engine off. Clean the

sounding the chime unexpectedly. You will

. The camera area of the windshield is misted

radar cover on the front of the vehicle with a

have to manually control the proper distance

or frozen.

soft cloth, and restart the engine. If the warning

away from the vehicle traveling ahead.

message continues to illuminate, check that the

cover of the sensor is not covered by dirt, snow

5-132

Starting and driving

or ice. If the warning light is still illuminated,

Action to take:

have the FCM system checked. It is recom-

If the warning light (orange) comes on, stop the

mended that you visit an authorized Mitsubishi

vehicle in a safe location. Turn the engine off

Motors dealer for this service.

and restart the engine. If the warning light

. When driving on roads with limited road

continues to illuminate, have the FCM system

structures or buildings (for example, long

checked. It is recommended that you

visit an

bridges, deserts, snow fields, driving next to

authorized

Mitsubishi

Motors

dealer

for

this

long walls).

service.

Action to take:

When the above conditions no longer exist, the

FCM system will resume automatically.

Condition C

WAF0392X

When the Active stability control (ASC) is OFF,

the FCM brake will not operate. In this case

SYSTEM MAINTENANCE

only visible and audible warning operates. The

FCM system warning light

(orange) will

The radar sensor is located on the front of the

illuminate.

vehicle. The camera is located on the upper

side of the windshield.

Action to take:

To keep the FCM system operating properly, be

When the ASC is ON, the FCM system will

sure to observe the following:

resume automatically.

. Always keep the sensor area on the front of

SYSTEM MALFUNCTION

the vehicle and windshield clean.

If the FCM system malfunctions, it will be

. Do not strike or damage the areas around

turned off automatically, a chime will sound, the

the sensors (ex. vehicle front area, wind-

FCM system warning light will (orange) will

shield).

illuminate and the warning message “Malfunc-

. Do not cover or attach stickers or similar

tion” will appear in the multi-information

objects on the front of the vehicle near the

display.

sensor area. This could cause failure or

malfunction.

Starting and driving

5-133

PREDICTIVE FORWARD

COLLISION WARNING (PFCW)

WARNING

Failure to follow the warnings and instructions

for proper use of the PFCW system could

result in serious injury or death.

. The PFCW system helps warn the driver

before a collision but will not avoid a

collision. It is the driver’s responsibility to

stay alert, drive safely and be in control of

the vehicle at all times.

The PFCW system can help alert the driver

when there is a sudden braking of a second

WAF0395X

vehicle traveling in front of the vehicle ahead in

the same lane.

The PFCW system uses a radar sensor

located on the front of the vehicle to measure

the distance to a second vehicle ahead in the

same lane.

Starting and driving

5-135

WAF0624X

Vehicle ahead detection indicator (on the multi-

information display)

Forward Collision Mitigation

(FCM) System

OFF warning light (on the meter panel)

5-136

Starting and driving

WAF0661X

PFCW SYSTEM OPERATION

The PFCW system operates at speeds above

approximately 3 MPH (5 km/h).

If there is a potential risk of a forward collision,

the PFCW system will warn the driver by

blinking the vehicle ahead detection indicator

, and sounding an audible alert.

Starting and driving

5-137

Content      ..     16      17      18      19     ..