DTC P1540: LIN Communication Check by
ECM (Sending Message to Radiator
Sensor) <California>/DTC P1541: LIN
Communication Check by ECM (Receiving
Message from Radiator Sensor)
<California>................

13Ab-658

DTC P1543: DOR Tampering Monitor
(Temperature Check After Thermostat
Open) <California>..........

13Ab-663

DTC P1544: DOR Tampering Monitor
(Temperature Check Before Thermostat
Open) <California>.........

.13Ab-666

DTC P1545: DOR Tampering Monitor
(Temperature Change After Thermostat
Open) <California>..........

13Ab-669

DTC P1546: DOR Tampering Monitor
(Temperature Check at Cold Start)
<California>................

13Ab-671

DTC P1547: DOR Tampering Monitor
(Rationality Check) <California>
............................

13Ab-674

DTC P1580: DOR Radiator Tampering
Monitor (Encrypted Message)
<California>................

13Ab-676

DTC P1590: TCM to ECM Communication
Error in Torque Reduction Request
............................

13Ab-678

DTC P1603: Battery Backup Line
Malfunction.................

13Ab-680

DTC P1676: Variant Coding. . .

13Ab-684

DTC P2066: Fuel Level Sensor (sub)
Circuit Range/Performance. . .

13Ab-686

DTC P2100: Throttle Actuator Control
Motor Circuit (Open)........

13Ab-690

DTC P2101: Throttle Actuator Control
Motor Magneto Malfunction. .

.13Ab-694

DTC P2122: Accelerator Pedal Position
Sensor (main) Circuit Low Input
............................

13Ab-697

DTC P2123: Accelerator Pedal Position
Sensor (main) Circuit High Input
............................

13Ab-702

DTC P2127: Accelerator Pedal Position
Sensor (sub) Circuit Low Input
............................

13Ab-706

DTC P2128: Accelerator Pedal Position
Sensor (Sub) Circuit High Input
............................

13Ab-710

DTC P2135: Throttle Position Sensor
(Main and Sub) Range/Performance
Problem.....................

13Ab-713

DTC P2138: Accelerator Pedal Position
Sensor (main and sub) Circuit Range/
Performance Problem.........

13Ab-717

13Ab-5

Continued on next page

DTC P2195: Heated Oxygen Sensor
Inactive (bank 1, sensor 1)
............................

13Ab-721

DTC P2197: Heated Oxygen Sensor
Inactive (bank 2, sensor 1)
............................

13Ab-724

DTC P2228: Barometric Pressure
Circuit Low Input...........

13Ab-727

DTC P2229: Barometric Pressure
Circuit High Input..........

13Ab-729

DTC P2252: Heated Oxygen Sensor
Offset Circuit Low Voltage
............................

13Ab-731

DTC P2253: Heated Oxygen Sensor
Offset Circuit High Voltage
............................

13Ab-733

DTC P2423: HC adsorber (HC trap
catalyst) efficiency below threshold
............................

13Ab-735

DTC P2567: LIN Communication Check by
Radiator Sensor (Thermistor Error)
<California>................

13Ab-737

DTC U0001: Bus Off..........

13Ab-739

DTC U0101: Transmission Control
Module Time-Out.............

13Ab-740

DTC U0114: AWD-ECU Time-Out
............................

13Ab-742

DTC U0121: ABS-ECU/ASC-ECU Time-Out
............................

13Ab-744

DTC U0141: ETACS-ECU Time-Out
............................

13Ab-746

DTC U0167: KOS-ECU/WCM Communication
Error.......................

13Ab-749

DTC U1180: Combination Meter Time-
Out.........................

13Ab-750

SYMPTOM PROCEDURES..........

13Ab-753

INSPECTION PROCEDURE 1: Scan Tool
Communication with ECM Is Not
Possible...................

.13Ab-753

INSPECTION PROCEDURE 2: The
Malfunction Indicator Lamp (SERVICE

ENGINE SOON or Check Engine Lamp) Does
Not Illuminate Right after the
Ignition Switch Is Turned to the "ON"
Position....................

13Ab-756

INSPECTION PROCEDURE 3: The
Malfunction Indicator Lamp (SERVICE
ENGINE SOON or Check Engine Lamp)
Remains Illuminated and Never Goes
Out.........................

13Ab-757

INSPECTION PROCEDURE 4: Cranks, Won't
Start.......................

13Ab-758

INSPECTION PROCEDURE 5: Starts Up and
Dies........................

13Ab-765

INSPECTION PROCEDURE 6: Hard
Starting....................

13Ab-770

INSPECTION PROCEDURE 7: Unstable Idle
(rough idle, hunting).......

13Ab-775

INSPECTION PROCEDURE 8: Idle speed is
high (improper idle speed).
............................

13Ab-779

INSPECTION PROCEDURE 9: Idle Speed Is
Low (improper idle speed).
...........................

.13Ab-780

INSPECTION PROCEDURE 10: When the
engine is cold, it stalls at idle (die
out)........................

13Ab-781

INSPECTION PROCEDURE 11: When the
Engine Is Hot, It Stalls at Idle (die
out)........................

13Ab-784

INSPECTION PROCEDURE 12: The Engine
Stalls when Accelerating (pass out).
............................

13Ab-787

INSPECTION PROCEDURE 13: The engine
stalls when decelerating.. . .

13Ab-789

INSPECTION PROCEDURE 14: Hesitation,
sag, stumble, Poor acceleration or
Surge.......................

13Ab-791

INSPECTION PROCEDURE 15: Acceleration
shock.......................

13Ab-794

INSPECTION PROCEDURE 16: Knocking
............................13Ab-795

13Ab-6

Continued on next page

Content .. 200 201 202 203 ..