Mitsubishi Outlander (2013+). Manual - part 569

 

  Index      Mitsubishi     Mitsubishi Outlander - service repair manual 2013 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  567  568  569  570   ..

 

 

Mitsubishi Outlander (2013+). Manual - part 569

 

 

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-35

Inspection Procedure 11: The comfort washing function does not work normally.

CAUTION

Before replacing the ECU, ensure that the power 
supply circuit, the earth circuit and the communi-
cation circuit are normal.

COMMENTS ON TROUBLE SYMPTOM

If the comfort washer function does not work nor-
mally, the windshield wiper switch input circuit(s), the 
windshield washer switch input circuit(s) and 
ETACS-ECU may have a problem.

NOTE: Without function as a default (Refer to 

P.51-37

.)

PROBABLE CAUSES

• Malfunction of column switch

• Malfunction of ETACS-ECU

• Damaged wiring harness and connectors

DIAGNOSIS PROCEDURE

STEP 1. Check the ETACS-ECU customisation 
function.
Use the ETACS-ECU customise function to check 
that the "Intelligent/ Comfort washer" is set to "Ena-
ble."

Q: Is the check result normal?

YES : 

Go to Step 2

NO : 

Use the ETACS-ECU customise function to 
set "Intelligent/ Comfort washer" to 
"Enable." (Refer to 

P.51-37

.)

STEP 2. M.U.T.-III diagnosis code
Check that ETACS-ECU sets a diagnosis code.

Q: Is the diagnosis code set?

YES : 

Carry out the troubleshooting on 

ETACS-ECU. (Refer to GROUP 54A 

− 

ETACS, Diagnosis Code Chart .)

NO : 

Go to Step 3

STEP 3. Windshield wiper operation check
Check that the windshield wipers work normally.

Q: Is the check result normal?

YES : 

Go to Step 4

NO : 

Refer to trouble symptom chart 

P.51-24

.

STEP 4. Windshield washer operation check
Check that the windshield washer works normally.

Q: Is the check result normal?

YES : 

Go to Step 5

NO : 

Refer to Inspection Procedure 10 "The 
windshield washer does not work normally 

P.51-33

."

STEP 5. System retest
Check that the comfort washer function works nor-
mally.

Q: Is the check result normal?

YES : 

Intermittent malfunction (Refer to GROUP 

00 

− How to Use 

Troubleshooting/Inspection Service Points 

− 

How to Cope with Intermittent Malfunction .)

NO : 

Replace the ETACS-ECU.

Inspection Procedure 12: Delayed finishing wipe function does not work normally.

CAUTION

Before replacing the ECU, ensure that the power 
supply circuit, the earth circuit and the communi-
cation circuit are normal.

COMMENT ON TROUBLE SYMPTOM

If the delayed finishing wipe function does not prop-
erly operate, the input circuit of windshield wiper 
switch, the input circuit of windshield washer switch, 
or ETACS-ECU may be defective.

PROBABLE CAUSES

• Malfunction of column switch

• Malfunction of ETACS-ECU

• Damaged harness wires and connectors

DIAGNOSIS PROCEDURE

STEP 1. Check the ETACS-ECU customisation 
function.
Use the ETACS-ECU customise function to check 
that the "front wiper washer" is set to "On with 
Delayed finishing wipe function."

Q: Is the check result normal?

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-36

YES : 

Go to Step 2.

NO : 

Use the ETACS-ECU customise function to 
set the "front wiper washer" to "On with 
Delayed finishing wipe function." (Refer to 

P.51-37

.)

STEP 2. M.U.T.-III diagnosis code
Check if the ETACS-ECU sets a diagnosis code.

Q: Is the diagnosis code set?

YES : 

Carry out the troubleshooting on 

ETACS-ECU. (Refer to GROUP 54A 

− 

ETACS, Diagnosis Code Chart .)

NO : 

Go to Step 3.

STEP 3. Windshield wiper operation check
Check that the windshield wipers work normally.

Q: Is the check result normal?

YES : 

Go to Step 4.

NO : 

Refer to trouble symptom chart 

P.51-24

.

STEP 4. Windshield washer operation check
Check that the windshield washers work normally.

Q: Is the check result normal?

YES : 

Go to Step 5.

NO : 

Refer to Inspection Procedure 10 
"Windshield washers do not work normally 

P.51-33

."

STEP 5. Retest the system
Check that the delayed finishing wipe function works 
normally.

Q: Is the check result normal?

YES : 

Intermittent malfunction. (Refer to GROUP 

00 

− How to Use 

Troubleshooting/Inspection Service Points 

− 

How to Cope with Intermittent Malfunction .)

NO : 

Replace the ETACS-ECU.

DATA LIST REFERENCE TABLE

M1511015100101

LIN (LIGHTING CONTROL SENSOR)

Item No. M.U.T.-III display

Check condition

Normal condition

7005

RLS rain sensor ON/OFF

When wiper switch is in any position other 
than AUTO

OFF

When wiper switch is in AUTO position

ON

7006

RLS rain sensor sensitivity

Changes from 1 to 6 according to the 
wiper volume.

1,2,3,4,5,6

7008

RLS wiper auto stop SW

Windshield wipers are in operation.

Park position

Other than above

Other than Park 
position

7013

RLS wiper control output

No operation request is received from 
lighting control sensor (rain sensor).

OFF

LO operation request is received from 
lighting control sensor (rain sensor).

Lo

HI operation request is received from 
lighting control sensor (rain sensor).

Hi

7020

RLS RS measurement 
value (RS1)

Lighting control sensor (rain sensor) 
detects rain drops.

The value changes 
when sensor 1 detects 
rain drops.

7021

RLS RS measurement 
value (RS2)

Lighting control sensor (rain sensor) 
detects rain drops.

The value changes 
when sensor 2 detects 
rain drops.

7022

RLS RS adaptation value 
(RS1)

Initializing after adaptation (Sensor 1)

Output amount when 
initializing (Sensor 1)

7023

RLS RS adaptation value 
(RS2)

Initializing after adaptation (Sensor 2)

Output amount when 
initializing (Sensor 2)

7024

RLS RS adaptation gain 
level

Initializing after adaptation

The calibrated value of 
initialising

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-37

ON-VEHICLE SERVICE

WINDSHIELD INTERMITTENT WIPER 
INSPECTION

M1511023600231

1. Check that the intermittent wiper interval is 

changed as the windshield intermittent wiper vol-
ume is operated.

2. Turn the windshield intermittent wiper switch to 

the intermittent operation position. Use the 
M.U.T.-III to set a simulated vehicle speed with 
the wiper volume held. The intermittent wiper 
interval should be changed as the simulated vehi-
cle speed is changed.

3. If either of above is defective, carry out the trou-

bleshooting. (Refer to 

P.51-29

)

LIGHTING CONTROL SENSOR (RAIN 
SENSOR) INSPECTION

M1511028400113

Under clear weather (windshield glass is dry), turn 
the ignition switch to "ON" position and wiper switch 
to "AUTO" position. Check that the wiper works when 
applying water to the upper part of the windshield 
glass where the lighting control sensor is installed. If 
there is a malfunction, perform the troubleshooting 
(Refer to 

P.51-24

).

COMFORT WASHING FUNCTION 
INSPECTION

M1511029600198

1. Operate the windshield washer switch for less 

than 0.25 second with the ignition switch in the 
ACC or ON position to check whether the comfort 
washer function works normally.

2. If not, carry out the troubleshooting. (Refer to 

P.51-35

.)

NOTE: Check that the comfort washer function is set 
to "Enabled" with the customise function. (Refer to 

P.51-53

.)

DELAYED FINISHING WIPE FUNCTION 
INSPECTION

M1511029800158

1. When the washer lever of the column switch is 

operated for 0.5 seconds or longer with the 
ignition switch in the ACC or ON position, or when 
the intelligent washer function is enabled, the 
Delayed finishing wipe function injects the washer 
fluid and operates the wiper. The wiper operates 
once 6 seconds after the wiper operation is 
stopped. Check that the Delayed finishing wipe 
function works normally.

2. If not, carry out the troubleshooting. (Refer to 

P.51-35

.)

NOTE: Check that the Delayed finishing wipe func-
tion is set by the customisation function. (Refer to 

P.51-53

.)

CUSTOMISATION FUNCTION

M1511027402291

By operating the M.U.T.-III ETACS system, the fol-
lowing functions can be customised. The pro-
grammed information is held even when the battery 
is disconnected.

Adjustment 
item (M.U.T.-III 
display)

Adjustment item

Adjusting content 
(M.U.T.-III display)

Adjusting content

Front wiper 
operation

Adjustment of the 
intermittent 
windshield wiper 
operation <vehicles 
without lighting 
control sensor>

Normal INT

Intermittent wiper interval is fixed to 4 
seconds.

Variable INT

Intermittent wiper interval is calculated only 
by the wiper volume control.

Speed Sensitive

Intermittent wiper interval is calculated 
according to the intermittent wiper volume 
control and vehicle speed (initial 
condition).

Adjustment of the 
intermittent 
windshield wiper 
operation <vehicles 
with lighting control 
sensor>

Normal INT

Intermittent wiper interval is fixed to 4 
seconds.

Variable INT

Intermittent wiper interval is calculated only 
by the wiper volume control.

Speed Sensitive

Intermittent wiper interval is calculated 
according to the intermittent wiper volume 
control and vehicle speed.

Rain Sensitive

Intermittent wiper interval is calculated 
according to the intermittent wiper volume 
control and lighting control sensor (initial 
condition).

Front /rear 
wiper washer

Disabling or 
enabling 
washer-linked wiper 
function

Only Washer

No function

Washer & Wiper

With function: Without delayed finishing 
wipe function <Initial condition>

With after wipe

With function: With delayed finishing wipe 
function

Intelligent/Comf
ort washer

With/without 
Comfort washer 
function

Disable

No function (Initial condition)

Enable

With function

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-38

 

 

 

 

 

 

 

Content   ..  567  568  569  570   ..