Mitsubishi Montero Sport (2004+). Manual - part 713

 

  Index      Mitsubishi     Mitsubishi Montero Sport - service repair manual 2004 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  711  712  713  714   ..

 

 

Mitsubishi Montero Sport (2004+). Manual - part 713

 

 

AUTOMATIC TRANSMISSION DIAGNOSIS

TSB Revision

AUTOMATIC TRANSMISSION

23A-417

INSPECTION PROCEDURE USING AN OSCILLOSCOPE

M1231109500119

Waveform sample

TERMINAL 
NO.

INSPECTION ITEM

INSPECTION REQUIREMENT

NORMAL CONDITION 
(WAVEFORM SAMPLE)

45

Crankshaft position 
sensor

Transmission 
range: N

Idling (Vehicle 
stopped)

Waveform A

103

Input shaft speed sensor Transmission 

range: 3

Driving at constant 
speed of 50 km/h 
(31 mph) in 3rd 
gear (Engine: 1,500 
− 2,000 r/min)

Waveform B

104

Output shaft speed 
sensor

80

Vehicle speed sensor

Waveform C

129

Low-reverse solenoid 
valve

• Ignition 

switch: ON

• Transmission 

range: P

• Engine: 

Stopped

• Throttle 

(Accelerator) 
opening 
angle: Less 
than 1 Volt

Force drive each 
solenoid valve 
(Actuator test)

Waveform D

120

Underdrive solenoid 
valve

106

Second solenoid valve

130

Overdrive solenoid valve

107

Torque converter clutch 
control solenoid valve

AC001872AE

WAVEFORM A

(V)

0

5

(ms)

AC001873AD

WAVEFORM B

(V)

0

5

(ms)

AC001873AE

WAVEFORM C

(V)

0

12

(ms)

AC001875AD

WAVEFORM D

(V)

0

20

(ms)

40

60

A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS

TSB Revision

AUTOMATIC TRANSMISSION

23A-418

A/T FAULTY OPERATION PREVENTION MECHANISM 

DIAGNOSIS

INTRODUCTION TO A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS

M1232001600282

If the key interlock and shift lock mechanisms indi-
cates a malfunction, the key interlock cable, the shift 
lock cable, or the selector lever assembly may be 
defective. In this case, follow troubleshooting below.

A/T KEY INTERLOCK AND SHIFT LOCK MECHANISM DIAGNOSTIC 
TROUBLESHOOTING STRATEGY

M1232001700289

Use these steps to plan your diagnostic strategy. If 
your follow then carefully, you will be sure that you 
have exhausted most of the possible ways to find 
automatic transmission key interlock and shift lock 
mechanism fault.
1. Gather information from the customer.

2. Verify that the condition described by the 

customer exists.

3. Find the malfunction by following the Symptom 

Chart.

4. Verify that the malfunction is eliminated.

SYMPTOM CHART <A/T FAULTY OPERATION PREVENTION MACHANISM>

M1232001800480

SYMPTOM

INSPECTION 
PROCEDURE

REFERENCE 
PAGE

Selector lever can be moved from "P" to "R" position without depressing 
brake pedal when ignition key is at any position other than "LOCK" 
(OFF) position.

1

P.23A-419

Selector lever cannot be moved from "P" to "R" position with brake 
pedal depressed when ignition key is at any position other than "LOCK" 
(OFF) position.

2

P.23A-419

Selector lever can be moved from "P" to "R" position with brake pedal 
depressed when ignition key is at "LOCK" (OFF) position.

3

P.23A-421

Selector lever cannot be moved from "P" to "R" position smoothly.

4

P.23A-421

Selector lever cannot be moved from "P" to "R" position.

5

P.23A-423

Ignition key cannot be turned to "LOCK" (OFF) position when selector 
lever is at "P" position.

6

P.23A-423

Ignition key can be turned to "LOCK" (OFF) position when selector lever 
is at any position other than "P" position.

7

P.23A-424

A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS

TSB Revision

AUTOMATIC TRANSMISSION

23A-419

SYMPTOM PROCEDURES <KEY INTERLOCK AND SHIFT LOCK MECHANISMS>

INSPECTION PROCEDURE 1: Selector Lever can be Moved from "P" to "R" Position without 
Depressing Brake Pedal when Ignition Key is at Positions other than "LOCK" (OFF) Position.

.

TECHNICAL DESCRIPTION (COMMENT)
Lock cam or shift lock cable may be defective.

.

TROUBLESHOOTING HINTS

• Malfunction of lock cam

• Malfunction of shift lock cable

DIAGNOSIS

STEP 1. Check the fit of the lock cam.

Q: Is the lock cam installed correctly?

YES : 

Go to Step 2.

NO : 

Install the lock cam correctly. Refer to 

P.23A-449

. When the brake pedal is 

released with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can not be 
moved from "P" position to "R" position.

STEP 2. Check the lock cam.

Q: Is the lock cam in good condition?

YES : 

Go to Step 3.

NO : 

Replace the lock cam. Refer to 

P.23A-449

When the brake pedal is released with the 
ignition key at other positions than "LOCK" 
(OFF) position, check that the selector lever 
can not be moved from "P" position to "R" 
position.

STEP 3. Check the fit of the shift lock cable.

Q: Is the shift lock cable installed correctly?

YES : 

Go to Step 4.

NO : 

Install the shift lock cable correctly. Refer to 

P.23A-451

. When the brake pedal is 

released with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can not be 
moved from "P" position to "R" position.

STEP 4. Check the shift lock cable.

Q: Is the shift lock cable in good condition?

YES : 

There is no action to be taken.

NO : 

Replace the shift lock cable. Refer to 

P.23A-451

. When the brake pedal is 

released with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can not be 
moved from "P" position to "R" position.

INSPECTION PROCEDURE 2: Selector Lever cannot be Moved from "P" to "R" Position with Brake 
Pedal Depressed when Ignition Key is at Positions other than "LOCK" (OFF) Position.

.

TECHNICAL DESCRIPTION (COMMENT)
Selector lever assembly, shift lock cable, key inter-
lock cable, transmission control cable, or lock cam 
may be defective.

.

TROUBLESHOOTING HINTS

• Malfunction of selector lever assembly

• Malfunction of shift lock cable

• Malfunction of key interlock cable

• Malfunction of transmission control cable

• Malfunction of lock cam

A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS

TSB Revision

AUTOMATIC TRANSMISSION

23A-420

DIAGNOSIS

STEP 1. Check the connection of lock cam and 
key interlock cable.

Q: Is the connection of lock cam and key interlock 

cable in good condition?

YES : 

Go to Step 2.

NO : 

Repair the connection of lock cam and shift 
lock cable. When the brake pedal is 
depressed with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can be moved 
from "P" position to "R" position.

STEP 2. Check the connection of selector lever 
assembly and shift transmission control cable.

Q: Is the connection of selector lever assembly and 

shift transmission control cable in good condition?

YES : 

Go to Step 3.

NO : 

Repair the connection of selector lever 
assembly and shift transmission control 
cable. When the brake pedal is depressed 
with the ignition key at other positions than 
"LOCK" (OFF) position, check that the 
selector lever can be moved from "P" 
position to "R" position.

STEP 3. Check the fit of the shift lock cable.

Q: Is the shift lock cable installed correctly?

YES : 

Go to Step 4.

NO : 

Install the shift lock cable correctly. Refer to 

P.23A-451

. When the brake pedal is 

depressed with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can be moved 
from "P" position to "R" position.

STEP 4. Check the shift lock cable.

Q: Is the shift lock cable in good condition?

YES : 

Go to Step 5.

NO : 

Replace the shift lock cable. Refer to 

P.23A-451

. When the brake pedal is 

depressed with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can be moved 
from "P" position to "R" position.

STEP 5. Check the fit of the key interlock cable.

Q: Is the key interlock cable installed correctly?

YES : 

Go to Step 6.

NO : 

Install the key interlock cable correctly. 
Refer to 

P.23A-451

. When the brake pedal 

is depressed with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can be moved 
from "P" position to "R" position.

STEP 6. Check the key interlock cable.

Q: Is the key interlock cable in good condition?

YES : 

Go to Step 7.

NO : 

Replace the key interlock cable. Refer to 

P.23A-451

. When the brake pedal is 

depressed with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can be moved 
from "P" position to "R" position.

STEP 7. Check the fit of the transmission control 
cable.

Q: Is the transmission control cable installed 

correctly?

YES : 

Go to Step 8.

NO : 

Install the transmission control cable 
correctly. Refer to 

P.23A-445

. When the 

brake pedal is depressed with the ignition 
key at other positions than "LOCK" (OFF) 
position, check that the selector lever can 
be moved from "P" position to "R" position.

STEP 8. Check the transmission control cable.

Q: Is the transmission control cable in good 

condition?

YES : 

Repair or replace the selector lever 

assembly. Refer to 

P.23A-445

 and 

P.23A-449

. When the brake pedal is 

depressed with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can be moved 
from "P" position to "R" position.

NO : 

Replace the transmission control cable. 
Refer to 

P.23A-445

. When the brake pedal 

is depressed with the ignition key at other 
positions than "LOCK" (OFF) position, 
check that the selector lever can be moved 
from "P" position to "R" position.

 

 

 

 

 

 

 

Content   ..  711  712  713  714   ..