Mitsubishi Montero (2002-2004). Manual - part 897

 

  Index      Mitsubishi     Mitsubishi Montero - service repair manual 2002-2004 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..

 

 

Mitsubishi Montero (2002-2004). Manual - part 897

 

 

DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>

TSB Revision

DIAGNOSTIC TROUBLE CODE PROCEDURES

23Ac-71

STEP 6. Measure the PCM output voltage to the speed 
sensor at the PCM connector D-134 by backprobing.
(1) Do not disconnect connector D-134.
(2) Disconnect connector C-02 at the output shaft speed 

sensor.

(3) Turn the ignition switch to the "ON" position.

(4) Measure the voltage between PCM terminal 73 and ground 

by backprobing.

• The voltage should measure between 4.5 and 4.9 volts.

(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?

YES : Go to Step 7.
NO :  Go to Step 9.

AC204681AC

CONNECTOR: D-134

D-134 (GR)

61 62

63 64

65 66 67 68 69 70 71 72 73

82

89

81

88

80

79

78

77

87

86

85

76

75

74

84

83

AC204918 BK

D-134 HARNESS CONNECTOR : 
HARNESS SIDE

76

85

65

72

71

73

82

75

81

74

63 64

66

70

69

68

67

78

87

79

88 89

80

77

86

62

61

83 84

DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>

TSB Revision

DIAGNOSTIC TROUBLE CODE PROCEDURES

23Ac-72

STEP 7. Check output shaft speed sensor connector C-02, 
PCM connector D-134 and intermediate connector E-114 
for loose, corroded or damaged terminals, or terminals 
pushed back in the connector.
Q: Are the connectors in good condition?

YES : Go to Step 8.
NO :  Repair or replace the damaged components. Refer to 

GROUP 00E, Harness Connector Inspection 

P.00E-

2

.

AC204746

CONNECTOR : C-02

C-02 (GR)

AB

1 2 3

AC204681AC

CONNECTOR: D-134

D-134 (GR)

61 62

63 64

65 66 67 68 69 70 71 72 73

82

89

81

88

80

79

78

77

87

86

85

76

75

74

84

83

AC204176

CONNECTOR : E-114

BD

38

28

16

33

22

10

31

19

7

1

18

30

29

17

5

6

21

20

32

8

2

9

25

13

3

24

23

3435

1112

27

26

3637

14

4

15

DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>

TSB Revision

DIAGNOSTIC TROUBLE CODE PROCEDURES

23Ac-73

STEP 8. Check the harness for open circuit or damage 
between output shaft speed sensor connector C-02 
terminal 2 and PCM connector D-134 terminal 73.
Q: Is the harness wire in good condition?

YES : Go to Step 19.
NO :  Repair or replace the harness wire.

AC204746

CONNECTOR : C-02

C-02 (GR)

AB

1 2 3

AC204681AC

CONNECTOR: D-134

D-134 (GR)

61 62

63 64

65 66 67 68 69 70 71 72 73

82

89

81

88

80

79

78

77

87

86

85

76

75

74

84

83

DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>

TSB Revision

DIAGNOSTIC TROUBLE CODE PROCEDURES

23Ac-74

STEP 9. Check output shaft speed sensor connector C-02, 
PCM connector D-134 and intermediate connector E-114 
for loose, corroded or damaged terminals, or terminals 
pushed back in the connector.
Q: Are the connectors and terminals in good condition?

YES : Go to Step 10.
NO :  Repair or replace the damages components. Refer to 

GROUP 00E, Harness Connector Inspection 

P.00E-

2

.

AC204746

CONNECTOR : C-02

C-02 (GR)

AB

1 2 3

AC204681AC

CONNECTOR: D-134

D-134 (GR)

61 62

63 64

65 66 67 68 69 70 71 72 73

82

89

81

88

80

79

78

77

87

86

85

76

75

74

84

83

AC204176

CONNECTOR : E-114

BD

38

28

16

33

22

10

31

19

7

1

18

30

29

17

5

6

21

20

32

8

2

9

25

13

3

24

23

3435

1112

27

26

3637

14

4

15

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..