Mitsubishi Galant. Manual - part 388

 

  Index      Mitsubishi     Mitsubishi Galant - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  386  387  388  389   ..

 

 

Mitsubishi Galant. Manual - part 388

 

 

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-19

6

Selector lever 
position: N (on a 
flat and straight 
road.)

Selector lever position 
and vehicle speed (Each 
condition should be 
maintained for 10 
seconds or more.)
(1)Idling in L range 
(Vehicle stopped)
(2)Driving at constant 
speed of 10 km/h (6.2 
mph) in L position
(3)Driving at constant 
speed of 30 km/h (19 
mph) in 2 position
(4)Driving at constant 
speed of 50 km/h (31 
mph) in 3 position
(5)Driving at constant 
speed of 50 km/h (31 
mph) in D position

Data list No. 63
(2) 1st, (3) 2nd, 
(4) 3rd, (5) 4th

Shift 
position

-

-

Data list No. 31
(2) 0 %, (3) 100 
%, (4) 100 %, (5) 
100 %

Low-
reverse 
solenoid 
valve duty 
%

31

Low-reverse 
solenoid valve 
system (

P.23A-

156

.)

Data list No. 32
(2) 0 %, (3) 0 %, 
(4) 0 %, (5) 100 
%

Underdrive 
solenoid 
valve duty 
%

32

Underdrive 
solenoid valve 
system (

P.23A-

164

.)

Data list No. 33
(2)100 %, (3) 0 
%, (4) 100 %, (5) 
0 %

Second 
solenoid 
valve duty 
%

33

Second 
solenoid valve 
system (

P.23A-

170

.)

Data list No. 34
(2) 100 %, (3) 
100 %, (4) 0 %, 
(5) 0 %

Overdrive 
solenoid 
valve duty 
%

34

Overdrive 
solenoid valve 
system (

P.23A-

177

.)

Data list No. 29
(1)0 km/h (0 
mph)
(4)50 km/h (31 
mph)

Vehicle 
speed 
sensor

29

Vehicle speed 
sensor system 
(

P.23A-150

.)

Data list No. 22
(4) 1,600 

 1,900 

r/min <2.4L 
Engine>
1,300 

 1.600 r/

min <3.0L 
Engine>

Input shaft 
speed 
sensor

22

Input shaft 
speed sensor 
system (

P.23A-

94

.)

Data list No. 23
(4) 1,600 

 1,900 

r/min <2.4L 
Engine>
1,300 

 1,600 r/

min <3.0L 
Engine>

Output 
shaft speed 
sensor

23

Output shaft 
speed sensor 
system (

P.23A-

105

.)

STEP CONDITION 

BEFORE TEST/
OPERATION

TEST/OPERATION

STANDARD

INSPECTI
ON ITEM

DTC

INSPECTION 
PROCEDURE 
PAGE

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-20

Selector lever 
position: 3 (on a 
flat and straight 
road.)

Selector lever position 
and vehicle speed
(1)Driving at speed of 50 
km/h (31 mph) in 3rd 
gear
(2)Driving at constant 
speed of 50 km/h (31 
mph)
(3)Release accelerator 
pedal (Speed under 50 
km/h (31 mph))

Data list No. 36
(2)70 

 90 %

(3)70 

 90 %

 0 

%

Torque 
converter 
clutch 
solenoid 
valve duty 
%

36, 
52, 
53

Torque 
converter 
clutch solenoid 
system (

P.23A-

184

,  

P.23A-

201

P.23A-

206

.)

Data list No. 52
(2)

10 to 10 r/

min
(3)

300 to 

100 

or 100 to 300 r/
min

Torque 
converter 
clutch 
amount of 
slippage

Use the scan 
tool (MUT-II) to 
stop the 
INVECS-II 
function.
Selector lever 
position: D (on a 
flat and straight 
road.)

Monitor data list No. 11, 
23, and 63 with the scan 
tool (MUT-II).
(1)Accelerate to 4th gear 
at a throttle position 
sensor output of 1.5V 
(accelerator opening 
angle of 30 %).
(2)Slowly decelerate to a 
stop.
(3)Accelerate to 4th gear 
at a throttle position 
sensor output of 2.5 V 
(accelerator opening 
angle of 50%).
(4)While driving at 60 
km/h (37 mph) in 4th 
gear, shift down to 3 
range.
(5)While driving at 40 
km/h (25 mph) in 3rd 
gear, shift down to 2 
range.
(6)While driving at 20 
km/h (12 mph) in 2nd 
gear, shift down to L 
range.

For (1), (2) and 
(3), the reading 
should be the 
same as the 
specified output 
shaft speed, and 
no abnormal shift 
shocks should 
occur.
For (4), (5) and 
(6), downshifting 
should occur 
immediately after 
moving the 
selector lever.

Malfunction 
when 
shifting

-

Shift shocks 
and slipping 
(

P.23A-233

.)

Does not 
shift 
according 
to 
instructions

-

Early or late 
shifting in all 
gears (

P.23A-

234

.)

-

Early or late 
shifting in 
some gears 
(

P.23A-237

.)

Does not 
shift

-

No diagnostic 
trouble code 
(

P.23A-239

.)

22

Input shaft 
speed sensor 
system (

P.23A-

94

.)

23

Output shaft 
speed sensor 
system (

P.23A-

105

.)

STEP CONDITION 

BEFORE TEST/
OPERATION

TEST/OPERATION

STANDARD

INSPECTI
ON ITEM

DTC

INSPECTION 
PROCEDURE 
PAGE

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-21

Use the scan 
tool (MUT-II) to 
stop the 
INVECS-II 
function.
Selector lever 
position: D (on a 
flat and straight 
road.)

Monitor data list No. 11, 
23, and 63 with the scan 
tool (MUT-II).
(1)Accelerate to 4th gear 
at a throttle position 
sensor output of 1.5V 
(accelerator opening 
angle of 30 %).
(2)Slowly decelerate to a 
stop.
(3)Accelerate to 4th gear 
at a throttle position 
sensor output of 2.5 V 
(accelerator opening 
angle of 50%).
(4)While driving at 60 
km/h (37 mph) in 4th 
gear, shift down to 3 
range.
(5)While driving at 40 
km/h (25 mph) in 3rd 
gear, shift down to 2 
range.
(6)While driving at 20 
km/h (12 mph) in 2nd 
gear, shift down to L 
range.

For (1), (2) and 
(3), the reading 
should be the 
same as the 
specified output 
shaft speed, and 
no abnormal shift 
shocks should 
occur.
For (4), (5) and 
(6), downshifting 
should occur 
immediately after 
moving the 
selector lever.

Does not 
shift from 1 
to 2 or 2 to 
1

31

Low-reverse 
solenoid valve 
system (

P.23A-

156

.)

33

Second 
solenoid valve 
system (

P.23A-

170

.)

41

1st gear 
incorrect ratio 
(

P.23A-192

.)

42

2nd gear 
incorrect ratio 
(

P.23A-192

.)

Does not 
shift from 2 
to 3 or 3 to 
2

33

Second 
solenoid valve 
system (

P.23A-

170

.)

34

Overdrive 
solenoid valve 
system (

P.23A-

177

.)

42

2nd gear 
incorrect ratio 
(

P.23A-192

.)

43

3rd gear 
incorrect ratio 
(

P.23A-192

.)

Does not 
shift from 3 
to 4 or 4 to 
3

32

Underdrive 
solenoid valve 
system (

P.23A-

164

.)

33

Second 
solenoid valve 
system (

P.23A-

170

.)

43

3rd gear 
incorrect ratio 
(

P.23A-192

.)

44

4th gear 
incorrect ratio 
(

P.23A-192

.)

STEP CONDITION 

BEFORE TEST/
OPERATION

TEST/OPERATION

STANDARD

INSPECTI
ON ITEM

DTC

INSPECTION 
PROCEDURE 
PAGE

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-22

TORQUE CONVERTER STALL TEST

M1231005400049

This test measures the maximum engine speed when the 
selector lever is at the "D" or "R" position and the torque 
converter stalls this test the operation of the torque converter, 
starter motor and one-way clutch operation and the holding 
performance of the clutches and brakes in the transaxle.

WARNING

Do not let anybody stand in front of or behind the 
vehicle while this test is being carried out.

1. Check the A/T fluid level and temperature. Check the engine 

coolant temperature.

A/T fluid level: At the "HOT" mark on the dipstick

A/T fluid temperature: 70 

 80 

°

C (158 - 176 

°

F)

Engine coolant temperature: 80 

 100 

°

C (176 - 212 

°

F

)

2. Chock both rear wheels.

3. Connect a tachometer.

4. Apply the parking and service brakes fully.

5. Start the engine.

6. Move the selector lever to the "D" position. Fully depress the 

accelerator pedal and read the maximum engine speed.

CAUTION

The throttle should not be left fully open for any more 
than eight seconds.

If carrying out the stall test two or more times, move the 
selector lever to the "N" position and run the engine at 
1,000 r/min to let the A/T fluid cool down before 
carrying out subsequent tests.

Standard value: Stall speed: 2,100 

−−−−

 2,600 r/min

7. Move the selector lever to the "R" position and repeat step 

6.

Standard value: Stall speed: 2,100 

−−−−

 2,600 r/min

9

Selector lever 
position: N (on a 
flat and straight 
road.)

Monitor data list No. 22 
and No. 23 with the scan 
tool (MUT-II).
(1)Move selector lever to 
R range, drive at 
constant speed of 10 km/
h (6.2 mph).

The ratio 
between data list 
No. 22 and No. 
23 should be the 
same as the gear 
ratio when 
reversing.

Does not 
engage

22

Input shaft 
speed sensor 
system (

P.23A-

94

.)

23

Output shaft 
speed sensor 
system (

P.23A-

105

.)

46

Reverse gear 
incorrect ratio 
(

P.23A-192

.)

STEP CONDITION 

BEFORE TEST/
OPERATION

TEST/OPERATION

STANDARD

INSPECTI
ON ITEM

DTC

INSPECTION 
PROCEDURE 
PAGE

AC001824 AB

REVERSE
CLUTCH

LOW-
REVERSE
BRAKE

ONE-WAY
CLUTCH

UNDER-
DRIVE
CLUTCH

TORQUE
CONVERTER

OVERDRIVE
CLUTCH

SECOND
BRAKE

 

 

 

 

 

 

 

Content   ..  386  387  388  389   ..