Mitsubishi Pajero Pinin. Manual - part 347

CHASSIS ELECTRICAL – 

Multi-Center Display <High Grade>

54A-104

INSPECTION PROCEDURE 10

Compass display does not change when not following a route, or guide does not appear when
searching for and following a route.

Carry out a sensor check (service function).

NG

If no vehicle speed is input, the sensor check does not complete.

OK

Carry out a vehicle signal check (service function).

D

Does “Shift position: R” appear when the shift position is R?

D

Does “Shift position: Except R” appear when the shift position
is not R?

NO

End (no abnormality)

YES

Measure at the C-52 multi-center display unit connector.

D

Connector disconnected

D

Voltage between terminal (22) and body ground
OK: 10 V or higher when shift position is R

NG

Check the harness between the back-up lamp switch and the
multi-center display unit, and repair if necessary.

OK

Replace the multi-center display unit.

INSPECTION PROCEDURE 11

One of the following messages appears during navigation mode.

D

The CD-drive has failure condition. Confirm and reload the disc, please.

D

Wrong disc is in the CD-drive. Insert a map disc, please.

D

No disc is in the CD-drive. Insert a map disc, please.

D

A music disc is in the CD-drive.

1.

“The CD-drive has failure condition. Confirm and reload the disc, please.” or “Wrong disc is
in the CD-drive. Insert a map disc, please.” appears.

CD is dirty or damaged.

YES

Insert a proper map disc.

NO

Insert the CD once more, and then press the NAVI switch. Does
the NAVI screen (compass display, outside route, route map) still
not appear?

YES

Replace the navigation unit.

NO

End

2.

“No disc is in the CD-drive. Insert a map disc, please.” or “A music disc is in the CD-drive”
appears.

Press the eject button on the CD-drive. Is the map disc a special
CD?

NO

Insert a proper map disc.

YES

Insert the map disc once more, and then press the NAVI switch.
Does the NAVI screen (compass display, outside route, route
map) still not appear?

NO

Replace the navigation unit.

YES

End

CHASSIS ELECTRICAL – 

Multi-Center Display <High Grade>

54A-105

ERROR CODE TABLE <ACCORDING TO SCREEN DISPLAY>

Error Code
No.

Error Details

Detection Method (Reference)

Refer-
ence
Page

1011

Ambient temperature sensor not con-
nected during diagnosis

Connection checking

54A-105

1021

Fuel gauge not connected during diagnosis

Connection checking

54A-106

1031

GPS abnormality during diagnosis

Connection checking

54A-106

1041

Engine-ECU not connected during diagno-
sis

Connection checking

54A-106

1051

SWS not connected during diagnosis

Connection checking

54A-106

1091

CD drive too hot during diagnosis

Connection checking

54A-106

1092 – 1096

CD drive abnormality during diagnosis

Connection checking

54A-107

10A1, 10B1

Memory of navigation unit abnormality
during diagnosis

Connection checking

54A-107

20D1, 30D1

Vehicle speed pulse abnormality during
diagnosis

Sensor checking

54A-107

20E1, 20E2,
30E1, 30E2

Gyro level abnormality during diagnosis

Sensor checking

54A-107

INSPECTION PROCEDURES FOR EACH ERROR CODE <ACCORDING TO
SCREEN DISPLAY>

Error Code No. 1011

Were the wiring check instructions followed?

NO

Repeat the wiring check.

YES

Repeat the wiring check. If the same problem occurs, check ambi-
ent temperature sensor.

Replace the ambient temperature sensor.

OK

Measure at the multi-center display connector B-08.

D

Disconnect connector.

D

Resistance between terminal (23) and body eartth.
OK: 500 

Ω

 – 100 k

Ω

NG

Check the harness between C-52 and A-89.

OK

Replace the multi-center display.

NG

CHASSIS ELECTRICAL – 

Multi-Center Display <High Grade>

54A-106

Error Code No. 1021

Were the wiring check instructions followed?

NO

Repeat the wiring check.

YES

Repeat the wiring check. If the same problem occurs, measure
at the multi-center display connector C-52.

D

Disconnect connector.

D

Ignition switch: ON

D

Voltage between terminal (33) and body eartth.
OK: 0.1 V (full tank full) – 3 V (fuel empty)

NG

Check the harness between C-52 and D-17.

OK

Replace the multi-center display.

Error Code No. 1031

Were the wiring check instructions followed?

NO

Repeat the wiring check.

YES

Repeat the wiring check. If the same problem occurs, there is
a malfunction of the GPS inside the multi-center display.

Replace the multi-center display.

Error Code No. 1041

Were the wiring check instructions followed?

NO

Repeat the wiring check.

YES

Connect MUT-

II 

and diagnose engine.

NG

Check the harness between C-53 and C-19.

OK

Replace the multi-center display.

Error Code No. 1051

Were the wiring check instructions followed?

NO

Repeat the wiring check.

YES

Check connector (C-53, C-83)

NG

Refer to GROUP 54B – Troubleshooting.

OK

Check SWS diagnosis trouble code.

Replace the multi-center display.

NG

Repair

OK

Error Code No. 1091

Is the navigation unit very hot because of direct sunlight, heat
air, etc.?

YES

Repeat the wiring check after the navigation unit becomes cool.

NO

Repeat the wiring check. If the same problem occurs, there is
a malfunction of the CD drive within the navigation unit.

Replace the navigation unit.

CHASSIS ELECTRICAL – 

Multi-Center Display <High Grade>

54A-107

Error Code No. 1092, 1093, 1094, 1095, 1096

Is a CD-ROM for this navigation system inside?

NO

Insert the CD-ROM for this navigation system.

YES

Is the CD-ROM inserted upside down?

YES

Insert the CD-ROM correctly.

Is the disc dirty, damaged or iced up?

YES

Repair or replace the disc.

NO

Repeat the wiring check. If the same problem occurs, there is
a malfunction of the CD drive within the navigation unit.

NO

Replace the navigation unit.

Error Code No. 10A1, 10B1

Were the wiring check instructions followed?

NO

Repeat the wiring check.

YES

Repeat the wiring check. If the same problem occurs, there is
a malfunction of the memory within the navigation unit..

Replace the navigation unit.

Error Code No. 20D1, 30D1

Were the sensor check instructions followed?

NO

Repeat the sensor check.

OK

Measure at the navigation unit connector B-08.

D

Disconnect connector.

D

Turn on the Ignition switch and then move the vehicle slowly.

D

Voltage between terminal (4) and body eartth.
OK: HI: 4 – 5 V, Lo: 0 – 1 V, pulse signal

NG

Check the vehicle speed sensor. (Refer to P.54A-27.)

OK

Replace the navigation unit.

YES

Check connector (B-08, C-50).

Repair

NG

Error Code No. 20E1, 20E2, 30E1, 30E2

Were the sensor check instructions followed?

NO

Repeat the sensor check.

YES

Repeat the sensor check. If the same problem occurs, there is
a malfunction of Gyro sensor within the navigation unit.

Replace the navigation unit.