Mitsubishi Lancer (4A9 engine). Manual - part 118

 

  Index      Mitsubishi     Mitsubishi Lancer (4A9 engine) 12GS41 & 44S - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  116  117  118  119   ..

 

 

Mitsubishi Lancer (4A9 engine). Manual - part 118

 

 

HEADLAMP

CHASSIS ELECTRICAL

54A-134

Comfort flasher With/without 

comfort flasher 
function

Disable

No function

Enable

With function (initial condition)

Comfort flasher 
switch time

Switch operation 
time to activate the 
comfort flasher 
function

Normal

0.4 second (initial condition)

Long

0.8 second

Hazard answer 
back

Adjustment of the 
number of keyless 
hazard warning 
lamp answer back 
flashes

Lock:1, Unlock:2

LOCK: Flashes once, UNLOCK: Flashes 
twice (initial condition)

Lock:1, Unlock:0

LOCK: Flashes once, UNLOCK: No flash

Lock:0, Unlock:2

LOCK: No flash, UNLOCK: Flash twice

Lock:2, Unlock:1

LOCK: Flash twice, UNLOCK: Flash once

Lock:2, Unlock:0

LOCK: Flash twice, UNLOCK: No flash

Lock:0, Unlock:1

LOCK: No flash, UNLOCK: Flash once

Lock:0, Unlock:0

No function

Sensitivity for 
auto lamp

Lighting control 
sensor sensitivity 
(illumination 
intensity) <vehicles 
with auto lamp>

Level 1 bright

High-high ambient brightness

Level 2 bright

High ambient brightness

Level 3

Standard ambient brightness (initial 
condition)

Level 4 dark

Low ambient brightness

Level 5 dark

Low-low ambient brightness

Head lamp auto 
cut customise

Adjustment of 
headlamp 
automatic shutdown 
function

Disable

No function

Enable (B-spec.)

With function (initial condition)

Coming home 
light

Disabling or 
enabling coming 
home light function

Disabled

No function

15 sec

The headlamps illuminate for 15 seconds.

30sec

The headlamps illuminate for 30 seconds. 
(initial condition)

60 sec

The headlamps illuminate for 60 seconds.

180 sec

The headlamps illuminate for 180 seconds.

Welcome light

Disabling or 
enabling welcome 
light function

Disabled

No function <Initial condition (vehicles for 
RUSSIA)>

Small

The tail lamp illuminates. <Initial condition 
(except vehicles for RUSSIA)>

Head

The headlamps illuminate.

Adjustment 
item (M.U.T.-III 
display)

Adjustment item

Adjusting content 
(M.U.T.-III display)

Adjusting content

HEADLAMP

CHASSIS ELECTRICAL

54A-135

HEADLAMP REMOVAL AND INSTALLATION

M1540101000506

REMOVAL SERVICE POINTS

<<A>> HEADLAMP CONTROL UNIT (HARNESS) 
REMOVAL <VEHICLES WITH DISCHARGE HEAD-
LAMP>

1. As shown in the figure, use the commercial tool to 

remove it.

Post-installation operation
Check the beam direction of the headlamp (Refer to 
Headlamp Aiming ).

AC613544AB

8

4.5 ± 1.5 N·m

9

1

2

3

4

5

6

7

3

4.5 ± 1.5 N·m

4.5 ± 1.5 N·m

1.5 ± 0.3 N·m

Grommet

Section A - A

1

A

A

Removal Steps 

Front bumper and radiator grille 
assembly (Refer to GROUP 51 - 
Front Bumper Assembly and 
Radiator Grille ).

1.

Headlamp assembly

2.

Headlamp bulb socket cover 
<Vehicles with discharge 
headlamp>

 

<<

A

>> >>

A

<<

3.

Headlamp control unit <Vehicles 
with discharge headlamp>

 

<<

B

>>

4.

Headlamp bulb <Vehicles with 
discharge headlamp>

5.

Headlamp bulb (low-beam) 
<Vehicles without discharge 
headlamp>

6.

Headlamp bulb (high-beam) 
<Vehicles without discharge 
headlamp> or bending lamp 
<Vehicles with discharge 
headlamp>

7.

Front turn-signal lamp bulb

8.

Position lamp bulb

9.

Grommet

AC712425AC

Commercial tool

HEADLAMP

CHASSIS ELECTRICAL

54A-136

2. To insert the tool available in the market into the 

headlamp assembly from the opening at the 
igniter side, firstly remove the headlamp control 
unit, the socket cover, the igniter and the earth 
connector. 

3. Using the commercial tool, make the resin washer 

sag to push up the harness above the resin 
washer.

4. Pull out the harness from the headlamp assembly.

 <<B>> HEADLAMP BULB REMOVAL <VEHICLES 
WITH DISCHARGE HEADLAMP>

CAUTION

Do not touch the bulb surface with bare hands or 
dirty gloves. If the bulb surface (glass part) gets 
dirty, immediately clean it with alcohol or thinner. 
After drying completely, install the bulb.
1. Twist the socket cover to remove.

2. Disconnect the igniter.

3. Release the bulb securing spring, and remove the 

bulb.

AC712430AC

Igniter

Earth
connector

Headlamp
control unit
connector

Commercial
tool

AC802237AB

Resin washer

Commercial tool

Headlamp control unit connector

Harness

Resin washer

Rib

AC613475

AB

Socket cover

AC609658

ZC501539

AC701335

AB

Igniter

AC609659

AC701336

AB

Spring

HEADLAMP

CHASSIS ELECTRICAL

54A-137

INSTALLATION SERVICE POINT

>>A<< HEADLAMP CONTROL UNIT INSTALLA-
TION <VEHICLES WITH DISCHARGE HEAD-
LAMP>

1. As shown in the figure, doubly wrap the portion in 

the vinyl tape, from the headlamp control unit 
connector root to the point where the harness 
separation is hidden.

2. Install the harness to the headlamp assembly. At 

that time, fitting the harness into the resin washer 
is unnecessary.

HEADLAMP LEVELLING SWITCH REMOVAL AND INSTALLATION

M1540105200148

AC712428AC

Plastic tape

Headlamp control
unit connector

AC712429

AC709853

AB

1

2

Removal Steps 

1.

Instrument lower panel (Refer to 
GROUP 52A 

− Instrument Lower 

Panel ).

2.

Headlamp levelling switch

 

 

 

 

 

 

 

Content   ..  116  117  118  119   ..