Mitsubishi Lancer Evolution 8. Manual - part 140

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution 8 - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  138  139  140  141   ..

 

 

Mitsubishi Lancer Evolution 8. Manual - part 140

 

 

SWS – TROUBLESHOOTING

54B-83

Are the tail lights and head lights working normally?

SWS monitor service data
(Function by Diagnosis) Lighting: Fog light
• Ignition switch: ON
• Tail light switch: ON
• Fog light switch: ON
Item No.

Item Name

Normal value

(a)  30

Ignition SW IG1

ON

(b) 36

Fog light

ON

OK:  Normal value displayed for all

Check connectors A-06X

Check fog light relay
(See Chap 54A Fog lights *)

Measure at the Fog light relay connector A-06X
• Remove the relay, and check on the relay box side
• Voltage between 2 and body earth
• Voltage between 4 and body earth
OK: Battery voltage

Check connectors A-12X

Check the harness between the fog light relay and the
front ECU

Confirm the trouble symptoms 

Transient problem

Check the head lights and tail lights (See Chart of
Trouble Symptoms)

To Inspection procedure R-2  Ignition switch (IG1) signal
not input (p.54B-96)

To Inspection procedure R-18 Fog light switch signal not
input (p.54B-110)

Check the harness between the fog light relay and the
special fuse, and repair.

Replace the front ECU

Inspection procedure L-1

Note: 
*: See ’00-5 Lancer Sedia Servicing Manual (No. 1036K00)

Fog lights do not light up correctly

Probable Cause

If any one of the fog lights does not light up correctly, but the
tail lights and head lights are working normally, then there is
probably a problem in the fog light switch input circuit system,
a problem in the fog light relay, or a fault in the front ECU. 

• Fault in fog light switch
• Fault in fog light relay
• Fault in front ECU
• Fault in harness or connectors

YES

OK

OK 

OK 

OK 

OK 

OK 

OK 

NO

NG (a)

NG (b)

NG

NG

NG

NG

NG

NG

Repair

Repair

Replace

Repair

SWS – TROUBLESHOOTING

54B-84

Inspection procedure L-2

Check connectors
(Fog light RH)  A-40
(Fog light LH)  A-35
(Fog light indicator light) C-108, C-106

Check the fog light bulb or fog light indicator bulb that is
not working

Measure at the Fog light connector A-40 (RH), A-35 (LH),
or the Fog light indicator light connector C-108

• Detach the connector and check on the harness side

(Fog light)

• Connectivity between 2 & body earth

(Fog light indicator light)

• Connectivity between 48 & body earth
OK: Connectivity

(Fog light indicator light)
Check connectors C-31

Check the harness between the fog light or fog light
indicator light that is not working, and the fog light relay,
and repair

Check the harness between the fog light or fog light
indicator light which is not working, and that body earth,
and repair

One of the fog lights does not light up (including fog light indicator light) Probable Cause

If any one of the fog lights does not light up normally, then there is probably a
fault in the harness/connectors, or a fault in the bulb

• Fault in fog light bulb
• Fault in harness or connectors

OK

OK

OK

OK

NG

NG

NG

NG

Repair

Replace

Repair

SWS – TROUBLESHOOTING

54B-85

Are the hazard lights working normally?

Check connectors C-224

Measure at ETACS-ECU connector C-224
• Detach the connector, and measure on the

junction box side

• Voltage between 11 & body earth
OK: Battery voltage

Check connector C-31

Check the harness between
ETACS-ECU connector and the
battery, and repair

Confirm the trouble symptoms 

Transient problem

To Inspection procedure R-2  Ignition switch (IG1) signal
not input (p.54B-96)

Transient problem

Confirm the trouble
symptoms

Replace the ETACS-
ECU 

To Inspection procedure R-5 RH turn indicator light
switch signal not input (p.54B-99)

To Inspection procedure R-5 LH turn indicator light switch
signal not input (p.54B-99)

Replace the ETACS-ECU 

SWS monitor service data
(Function by Diagnosis) Turn indicator lights: R turn
signal
• Turn indicator light switch: RH
• Ignition switch: ON
Item No.

Item Name

Normal state

(a)  30

Ignition SW IG1

ON

(b)  10

RH turn indicator SW

ON

OK:  Normal value displayed for all

SWS monitor service data
(Function by Diagnosis) Turn indicator lights: L turn
signal
• Turn indicator light switch: LH
• Ignition switch: ON
Item No.

Item Name

Normal state

11

LH turn indicator SW

ON

OK:  Normal value displayed

Inspection procedure M-1

Turn indicator lights do not light up

Probable Cause

If none of the turn indicator lights is working, then there is
probably a problem in the ignition switch (IG1) or turn
indicator light switch input circuit system, or a fault in the
ETACS-ECU.

• Fault in column switch
• Fault in ETACS-ECU 
• Fault in harness or connectors

YES

NO

OK

OK

NG

OK

NG

NG

NG

OK

Repair

Repair

NG (a)

NG (b)

NG 

OK 

NG 

OK 

OK 

SWS – TROUBLESHOOTING

54B-86

Inspection procedure M-2

Are the turn indicator lights working normally?

SWS monitor service data
ETACS switch data
• Hazard switch: ON
Item No.

Item Name

Normal state

04

Hazard light SW

ON

OK:  Normal value displayed

Confirm the trouble symptoms 

Transient problem

To Inspection procedure M-1 Turn indicator lights do not
light up (p.54B-85)

To Inspection procedure R-13 Hazard light switch signal
not input (p.54B-105)

Replace the ETACS-ECU 

Hazard lights do not light up

Probable Cause

If the hazard lights do not light up, then there is probably a
problem in the hazard light switch input circuit system, or a
fault in the ETACS-ECU.

• Fault in hazard light switch
• Fault in ETACS-ECU 
• Fault in harness or connectors

YES

OK

OK

NG

NG

NO

 

 

 

 

 

 

 

Content   ..  138  139  140  141   ..