Mitsubishi Lancer Evolution 8. Manual - part 139

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution 8 - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  137  138  139  140   ..

 

 

Mitsubishi Lancer Evolution 8. Manual - part 139

 

 

SWS – TROUBLESHOOTING

54B-79

Do the head lights (low beam and high beam) light up
correctly?

Confirm the trouble symptoms 

Transient problem

To Inspection procedure K-3 Head lights (low beam) do
not light up (p.54B-77) and Inspection procedure K-4
Head lights (high beam) do not light up (p.54B-78) 

To Inspection procedure R-5 Passing switch signal not
input (p.54B-99)

Replace the front ECU

SWS monitor service data
(Communications data)  Column ECU
• Passing switch: ON
Item No.

Item Name

Normal value

03

Passing SW

ON

OK:  Normal value displayed for all

Inspection procedure K-5

Head lights (low beam and high beam) do not light up
when passing switch is ON

Probable Cause

If neither of the head lights (low beam and high beam) lights
up properly, then there is probably a problem in the passing
switch input circuit system or a fault in the front ECU

• Fault in column switch 
• Fault in column ECU
• Fault in front ECU
• Fault in harness or connectors

YES

OK

OK

NO

NG

NG

SWS – TROUBLESHOOTING

54B-80

Inspection procedure K-6

Do the tail lights and head lights light up normally?

Is the head light automatic cut-off function set to
“Function switched off” by the adjustment function?

SWS monitor service data
(Function by Diagnosis) Lighting: Automatic cut-off
(1) Ignition switch: ON
(2) Ignition switch: ON 

OFF

Item No.

Item Name

Normal value

(a)  30

Ignition SW IG1

OFF

(3) 

Driver’s door: Open

Item No.

Item Name

Normal value

(b)  32

Front door SW RH

ON

(c)  35

HD light auto cut-off

ON

OK:  Normal value displayed for all

Confirm the trouble symptoms 

Transient problem

Check the head lights and tail lights (see Chart of
Trouble Symptoms) 

Use the adjustment function to set the headlight
automatic cut-off function to “Function ON” (p.54B-118)

To Inspection procedure R-2  Ignition switch (IG1) signal
not input (p.54B-96)

To Inspection procedure R-4 Driver’s door switch signal
not input (p.54B-98)

Replace the ETACS-ECU 

Replace the front ECU

Head light automatic cut-off function not working correctly

Probable Cause

This function is operated by determining input signals from the
ignition switch (IG1) and the driver’s door switch in the ETACS-
ECU. If it does not work properly, then there is probably a
malfunction in the input circuit system, a fault in the front ECU or a
fault in the ETACS-ECU.
It is also a possibility that the function has been switched off by the
adjustment function.

• Fault in driver’s door switch
• Fault in front ECU
• Fault in ETACS-ECU 
• Fault in harness or connectors

YES

YES

OK

OK

NO

NO

NG (a)

NG (b)

NG (c)

NG 

SWS – TROUBLESHOOTING

54B-81

Check connector
(RH head light (LO)) A-41
(RH head light (HI)) A-23
(LH head light (LO)) A-33
(LH head light (HI)) A-16
(High beam indicator light) C-106

Check the head light bulb that is not working, or the high
beam indicator bulb

(Head light (LO))
Measure at the Head light (LO) connector A-41 (RH), A-
33 (LH)
• Detach the connector and check on the harness side

(Car not fitted with discharge head lights)
• Connectivity between 3 & body earth
(Car fitted with discharge head lights)
• Connectivity between 8 & body earth
OK: Connectivity

(Head light (HI))
Measure at the Head light (HI) connector A-23 (RH), A-
16 (LH)
• Detach the connector and check on the harness side
• Connectivity between 2 & body earth
OK: Connectivity
(High beam indicator light)
Measure at the Combination meter connector C-106
• Detach the connector and check on the harness side
• Connectivity between 5 & body earth
OK: Connectivity

Check connector
(High beam indicator light)  C-31

Check the harness between the head light that is not
working or the combination meter, and the special fuse,
and repair

Check the harness between the head light that is not
working or the combination meter, and the body earth,
and repair

Inspection procedure K-7

One of the head lights does not light up (including high
beam indicator light)

Probable Cause

If any one of the head lights does not light up correctly, then
there is probably a fault in the harness connectors, or a fault
in the bulb, or the fuse has blown.

• Fault in headlight bulb
• Fault in high beam indicator bulb
• Fault in harness or connectors

Replace

Repair

OK

OK

OK

OK

NG

NG

NG

NG

Repair

SWS – TROUBLESHOOTING

54B-82

Inspection procedure K-8

Check connectors
(Tail light RH)  F-10
(Tail light LH)   F-15
(Position light RH)  A-41
(Position light LH)   A-33
(Licence plate light RH)  F-12
(Licence plate light LH)  F-13

Check connectors
(Tail light RH) C-215, C-209, C-07, C-31
(Tail light LH)  C-29, C-31
(Licence plate light) F-14, C-29, C-31

Check the harness between the rear combination light,
front combination light or licence plate light that is not
working, and the special fuse, and repair

(Licence plate light)
Check connector F-14

Check the harness between the rear combination light,
front combination light or licence plate light that is not
working, and the body earth, and repair.

Check the head light bulb that is not working

(Tail light)
Measure at the Rear combination light connector F-10
(RH) and F-15 (LH)
• Detach the connector and check on the harness side
• Connectivity between 5 & body earth
OK: Connectivity
(Position light)
Measure at the Front combination light connector A-
41(RH) A-33(LH)
• Detach the connector and check on the harness side
(Car not fitted with discharge headlights)
• Connectivity between 3 & body earth
(Car fitted with discharge headlights)
• Connectivity between 7 & body earth
OK: Connectivity
(License plate light)
Measure at the at the Licence plate light connector 
F-12(RH), F-13(LH) 
• Detach the connector and check on the harness side
• Connectivity between 1 & body earth
OK: Connectivity

One of the tail lights, position lights, or licence plate
lights does not light up

Probable Cause

If any one of the tail lights, position lights or licence plate
lights does not light up correctly, then there is probably a fault
in the harness connectors, or a fault in the bulb, or the fuse
has blown.

• Fault in tail light bulb
• Fault in position light
• Fault in licence plate light bulb
• Fault in harness or connectors

OK

NG

NG

NG

OK

OK

OK

NG

OK

NG

Repair

Repair

Replace

Repair

 

 

 

 

 

 

 

Content   ..  137  138  139  140   ..