Mitsubishi Lancer Evolution 8. Manual - part 133

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution 8 - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  131  132  133  134   ..

 

 

Mitsubishi Lancer Evolution 8. Manual - part 133

 

 

SWS – TROUBLESHOOTING

54B-55

Is the sunroof working correctly in normal operation?

SWS monitor ECU check
• Ignition switch: OFF
• Multi-mode operation performed using keyless entry

transmitter

(1)  ETACS-ECU
(2)  Sunroof ECU
OK: “OK” is displayed for all

SWS monitor service data
(Diagnosis by Function) Multi-mode keyless entry  Multi-
close
• Ignition switch: OFF
• Multi-mode operation performed using keyless entry

transmitter

Item No.

Item Name

Normal state

(a) 34

Multi-mode keyless

Multi-close 

(b) 72   Sunroof ECU response  Normal response*
OK: All display normal state

Transient problem

To Inspection procedure F-1  Sunroof not working at
all (p.54B-56)

To Inspection procedure A-3  No communication with
ETACS-ECU (p.54B-28)

To Inspection procedure A-6  No communication with
sunroof motor assembly (p.54B-31)

Replace the ETACS-ECU 

Replace the sunroof motor assembly

Inspection procedure E-6

Note:
*: About 30 seconds after the end of the multi-mode operation, the display will change from “normal response” to “sleep
response”.

Sunroof close operation not working correctly with multi-mode
keyless entry function

Probable Cause

If the sunroof is working correctly in normal operation, then
there is probably a fault in the ETACS-ECU.

• Fault in ETACS-ECU 
• Fault in sunroof motor assembly

YES

NO

NG (1)

NG (a)

NG (b)

NG (2)

OK

OK

SWS – TROUBLESHOOTING

54B-56

Inspection Procedure F-1

Check connector D-27

Measure at the Sunroof motor assembly connector D-27
• Detach the connector and measure at the harness side
• Voltage between 1 & body earth
OK: Battery voltage

Check the harness between the sunroof motor assembly
and the battery voltage, and repair

Measure at the Sunroof motor assembly connector D-27
• Detach the connector and measure at the harness side
• Ignition switch: ON
• Voltage between 2 & body earth
OK: Battery voltage

Measure at the Sunroof motor assembly connector D-27
• Detach the connector and measure at the harness side
• Connectivity between 5 & body earth
OK: Connectivity

Measure at the Sunroof switch connector D-26
• Detach the connector and measure at the harness side
• Connectivity between 4 & body earth
OK: Connectivity

Check connector D-26

Check the sunroof switch (See Chap. 42) *

Confirm the trouble symptoms

Transient problem

Check connectors C-113, C-223, C-210, C-32

Check connectors C-216, C-210

Check the harness between the sunroof motor assembly
and the ignition switch (IG2), and repair

Check the harness between the sunroof motor assembly
and the body earth, and repair

Check the harness between the sunroof switch and the
body earth, and repair

Replace the sunroof motor assembly

Sunroof not working at all

Probable Cause

There is probably a fault in the sunroof switch, a problem in
the sunroof motor assembly power circuit, or a fault in the
sunroof motor assembly.

• Fault in sunroof switch
• Fault in sunroof motor assembly
• Fault in harness or connectors

Note:
*: See ’00-5 Lancer Cedia Servicing Manual (No. 1036K00)

OK

OK

NG

NG

Repair

Repair

OK

NG

NG

NG

Repair

OK

OK

OK

OK

OK

OK

OK

NG

NG

NG

NG

NG

Repair

Repair

SWS – TROUBLESHOOTING

54B-57

SWS monitor ECU check
• Ignition switch: OFF
(1)  ETACS-ECU
(2)  Sunroof ECU
OK: “OK” is displayed for all

SWS monitor service data
(Diagnosis by Function) Sunroof: Sunroof operation
• Ignition switch: ON ‡ OFF
• P/W lock SW: OFF
Item No.

Item Name

Normal state

(a) 30

Ignition SW IG1

OFF

(b) 72    Sunroof ECU response            Normal response
OK: All display normal state

SWS monitor service data
(Diagnosis by Function) Sunroof: Sunroof operation
• Sunroof switch: Particular 
Item No.

Item Name

Normal value

72       Sunroof ECU response    Input check

OK: Displays normal value at appropriate switch position

Confirm the trouble symptoms 

Transient problem

Confirm the trouble symptoms 

Transient problem

Replace the sunroof motor assembly

Replace the sunroof switch

Replace the sunroof motor assembly

To Inspection procedure A-3  No communication with
ETACS-ECU (p.54B-28)

To Inspection procedure A-6  No communication with
sunroof motor assembly (p.54B-31)

To Inspection procedure R-2 Ignition switch (IG1)
signal not input  (p.54B-96)

Replace the sunroof motor assembly

Replace the sunroof motor assembly

Inspection procedure F-2

Note 
When performing the SWS monitor service data check, the normal analysis value for Item No.72 Sunroof ECU response will
show “Normal response” for about 30 seconds, before changing to “Sleep response”. The sunroof timer period can be
extended by means of a delay operation. (See ’00-5 Lancer Cedia Servicing Manual (No. 1036K00))

Inspection procedure F-3

Sunroof timer function not working

Probable Cause

This function is operated by determining the ignition switch
(IG1) signal from the ignition switch (IG2) circuit of the sunroof
motor assembly and the ETACS-ECU.

• Fault in sunroof motor assembly
• Fault in ETACS-ECU 
• Fault in harness or connectors

Particular sunroof functions not working

Probable Cause

If particular sunroof functions cannot be operated, then there
is probably a fault in the sunroof motor assembly, or the
sunroof switch. 

• Fault in sunroof motor assembly
• Fault in sunroof switch

Sunroof trap prevention function not working correctly

Probable Cause

There is probably a fault in the rotation detector sensor of the
sunroof motor assembly.

• Fault in sunroof motor assembly

Inspection procedure F-4

OK

OK

OK

OK

OK

NG

NG

NG

NG (b)

NG (a)

NG (1)

NG (2)

SWS – TROUBLESHOOTING

54B-58

Inspection procedure G-1

SWS monitor ECU check
• Ignition switch: OFF
(1) Column switch
(2) Front ECU
OK: “OK” is displayed for all

SWS monitor service data
(Diagnosis by Function) Windscreen wipers: INT
• Ignition switch: ACC
• Windscreen wiper switch: INT
Item No.

Item Name

Normal value  

(a) 05

INT wiper SW      ON

(b) 70    Front ECU response          Normal response or 

high beam response

OK: All display normal value

Check connector A-13X

Measure at Front ECU connector A-13X
• Detach the connector and measure at the relay box

side

• Ignition switch: ACC
• Voltage between 24 & body earth
OK: Battery voltage

Check connector B-12

Check the windscreen wiper motor (See Chap. 51*)

Measure at Windscreen wiper motor connector B-12
• Detach the connector and measure at the harness side
• Connectivity between 5 & body earth
OK: Connectivity

Check connector C-34

Confirm the trouble symptoms

Transient problem

To Inspection procedure A-2  No communication with
column switch (column ECU) (p.54B-27)

To Inspection procedure A-4 No communication with
front ECU (p.54B-29)

Replace the column ECU

Replace the front ECU

Check connectors C-21, C-209, C-210

Check the harness between the front ECU and the
ignition switch (ACC)

Check the harness between windscreen wiper motor
and the body earth

Replace the front ECU

Note:
*: See ’00-5 Lancer Cedia Servicing Manual (No. 1036K00)

Windscreen wipers not working at all

Probable Cause

There is probably a fault in the windscreen wipers, a fault in
the column ECU or a fault in the front ECU.
If the SWS monitor ECU check returns an NG result, then the
wiper backup circuit should also be checked, and repaired, if
necessary.

• Fault in column switch
• Fault in front ECU
• Fault in harness or connectors

OK

NG (1)

NG (a)

NG (b)

NG (2)

OK

OK

Repair

Repair

Repair

Repair

Replace

NG

NG

NG

NG

NG

NG

NG

NG

OK

OK

OK

OK

OK

OK

OK

 

 

 

 

 

 

 

Content   ..  131  132  133  134   ..