Mitsubishi Lancer Evolution 7. Manual - part 247

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution 7 - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  245  246  247  248   ..

 

 

Mitsubishi Lancer Evolution 7. Manual - part 247

 

 

MANUAL TRANSMISSION - Troubleshooting <ACD>

22A-11

Code No.25 Wrong-diameter tire

Probable cause

Code No.25 is output as wrong-diameter tire when one of the four vehicle

speeds is outside the range of specified values in respect to the average of the

four vehicle speed sensors, when the vehicle speed is above 20 km/h with the

steering wheel in the straight ahead position.

However the warning lamp does not light up.

D

Tire fault

D

Wheel speed sensor fault

D

Rotor fault

D

Wheel bearing fault

D

Harness or connector fault

D

ABS-ECU fault <Vehicles with ACD and AYC>

D

4WD-ECU fault

<Vehicles with ACD and AYC>

OK

NG

OK

Check the following connector: C-44

NG→Repair

Check the following connectors:

<L.H. drive vehicles> C-44, B-123

<R.H. drive vehicles> C-44, C-147, B-123

NG→Repair

OK

YES

OK

OK

Check the wheel speed sensor and rotor.

(Refer to GROUP 35B - Wheel Speed Sensor.)

NG→Repair

Check the wheel speed sensor output voltage. (Refer to

GROUP 35B - On-vehicle Service.)

OK

Check the wheel speed sensor installation.

NG→Repair

NG

OK

Check the wheel beearing. (Refer to GROUP 26 - On-vehicle

Service, and GROUP 27B - Rear Hub Assembly.)

NG→Repair

OK

Check the following connectors:

<L.H. drive vehicles> B-123, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-128, A-43

<R.H. drive vehicles> B-123, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-128, C-136

NG→Repair

NG

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions.)

Measure at 4WD-ECU connector C-44.
D

Measure the ECU terminal voltage.

D

Ignition switch: ON

D

Rotate the tire corresponding to the measured terminal by

one and a half to one rotate per second.

(1) Voltage between terminal 9 and body earth <FR>

(2) Voltage between terminal 6 and body earth <FL>

(3) Voltage between terminal 7 and body earth <RR>

(4) Voltage between terminal 8 and body earth <RL>

OK: Changes by 0 V ↔ 5 V.

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

NG→Replace the 4WD-ECU.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

Refer to GROUP 35B - Troubleshooting. (Refer to Diagnosis

Code No.11, 12, 13, 14, 21, 22, 23, and 24.)

Are all four wheels mounted to normal tires?

NO→Repair

Check the harness between the ABS-ECU and each wheel

speed sensor.
D

Check for open circuit and ground of the output line.

D

Check for open circuit and damage of the earth line.

NG→Repair

OK

Check the harness between the 4WD-ECU and

ABS-ECU.
D

Check for open circuit, ground and damage of

the power line.

NG→Repair

OK

MANUAL TRANSMISSION - Troubleshooting <ACD>

22A-12

<Vehicles with ACD>

OK

OK

NG

OK

NG

OK

OK

OK

NG

Measure at 4WD-ECU connector C-44.
D

Disconnect the connector and measure at the harness

side.

(1) Resistance between terminals 9 and 22 (vehicle speed

sensor <FR>)

(2) Resistance between terminals 6 and 19 (vehicle speed

sensor <FL>)

(3) Resistance between terminals 7 and 20 (vehicle speed

sensor <RR>)

(4) Resistance between terminals 8 and 21 (vehicle speed

sensor <RL>)

OK: 1.2 - 1.6 kΩ

Check the wheel speed sensor.

(Refer to GROUP 35B - Wheel Speed Sensor.)

NG→Replace

Check the installation of the wheel speed sensor.

NG→Repair

Check the wheel speed sensor and rotor.

(Refer to GROUP 35B - Wheel Speed Sensor.)

NG→Repair

Check the wheel beearing. (Refer to GROUP 26 - On-vehicle

Service, and GROUP 27B - Rear Hub Assembly.)

NG→Repair

OK

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

Check the following connectors:

<L.H. drive vehicles> C-44, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-128, A-43

<R.H. drive vehicles> C-44, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-136, C-147

NG→Repair

Check the harness between the 4WD-ECU and each wheel

speed sensor.
D

Check for open circuit and ground of the output line.

D

Check for open circuit and damage of the earth line.

NG→Repair

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

NG→Replace the 4WD-ECU.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

OK

Check the following connector: C-44

NG→Repair

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

NG→Replace the 4WD-ECU.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

Check the wheel speed sensor output voltage. (Refer to

P.22A-44.)

MANUAL TRANSMISSION - Troubleshooting <ACD>

22A-13

Code No.26 Wheel speed sensor system (faulty output

signal)

Probable cause

Code No.26 is output as output signal error of the wheel speed sensor when

one wheel speed is outside the specified range at the vehicle speed of above

20 km/h.

However, warning lamp will light up.

D

Tire fault

D

Wheel speed sensor fault

D

Rotor fault

D

Wheel bearing fault

D

Harness or connector fault

D

ABS-ECU fault <Vehicles with ACD and AYC>

D

4WD-ECU fault

<Vehicles with ACD and AYC>

OK

NG

OK

Check the following connector: C-44

NG→Repair

Check the following connectors:

<L.H. drive vehicles> C-44, B-123

<R.H. drive vehicles> C-44, C-147, B-123

NG→Repair

OK

Check the harness between the 4WD-ECU and ABS-ECU.
D

Check for open circuit, ground and damage of the power

line.

NG→Repair

YES

OK

OK

Check the wheel speed sensor and rotor.

(Refer to GROUP 35B - Wheel Speed Sensor.)

NG→Repair

Check the wheel speed sensor output voltage. (Refer to

GROUP 35B - On-vehicle Service.)

OK

Check the installation of the wheel speed sensor.

NG→Repair

NG

OK

Check the wheel beearing.

(Refer to GROUP 26 - On-vehicle Service, and GROUP 27B

- Rear Hub Assembly.)

NG→Repair

OK

Check the following connectors:

<L.H. drive vehicles> B-123, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-128, A-43

<R.H. drive vehicles> B-123, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-128, C-136

NG→Repair

NG

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

Measure at 4WD-ECU connector C44.
D

Measure the ECU terminal voltage.

D

Ignition switch: ON

D

Rotate the tire corresponding to the measured terminal by

one and a half to one rotate per second.

(1) Voltage between terminal 9 and the body earth <FR>

(2) Voltage between terminal 6 and body earth <FL>

(3) Voltage between terminal 7 and body earth <RR>

(4) Voltage between terminal 8 and body earth <RL>

OK: Changes at 0 V ↔ 5 V.

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

NG→Replace the 4WD-ECU.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

Check the harness between the ABS-ECU and each wheel

speed sensor.
D

Check for open circuit, ground, and short circuit of the

output line.

D

Check for open circuit and damage of the earth line.

NG→Repair

YES

NO

Refer to GROUP 35B - Troubleshooting.

Are the four wheels mounted to normal tires.

NO→Repair

MUT-II Diagnosis Code
D

Are the ABS Diagnosis Code Nos.11, 12, 13, 14, 21, 22,

23, 24 output?

MANUAL TRANSMISSION - Troubleshooting <ACD>

22A-14

<Vehicles with ACD>

OK

OK

NG

OK

NG

OK

OK

OK

NG

Measure at 4WD-ECU connector C-44.
D

Disconnect the connector and measure at the harness

side.

(1) Resistance between terminals 9 and 22 (vehicle speed

sensor <FR>)

(2) Resistance between terminals 6 and 19 (vehicle speed

sensor <FL>)

(3) Resistance between terminals 7 and 20 (vehicle speed

sensor <RR>)

(4) Resistance between terminals 8 and 21 (vehicle speed

sensor <RL>)

OK: 1.2 - 1.6 kΩ

Check the wheel speed sensor. (Refer to GROUP 35B -

Wheel Speed Sensor.)

NG→Replace

Check the installation of the wheel speed sensor.

NG→Repair

Check the wheel speed sensor and rotor.

(Refer to GROUP 35B - Wheel Speed Sensor.)

NG→Repair

Check the wheel bearing (Refer to GROUP 26 - On-vehicle

Service, and GROUP 27B - Rear Hub Assembly.)

NG→Repair

OK

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

Check the following connectors:

<L.H. drive vehicles> C-44, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-128, A-43

<R.H. drive vehicles> C-44, A-03, A-37, D-10, D-04, D-30,

C-146, C-111, C-136, C-147

NG→Repair

Check the harness between the 4WD-ECU and wheel speed

sensor.
D

Check for open circuit, grounding, and short-circuit of the

output line.

D

Check for open circuit and damage of the earth line

NG→Repair

MUT-II Data List
D

No.01 Vehicle speed sensor <FR>

D

No.02 Vehicle speed sensor <FL>

D

No.03 Vehicle speed sensor <RR>

D

No.04 Vehicle speed sensor <RL>

OK: The speed meter display and MUT-II display match.

NG→Replace the 4WD-ECU.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

OK

Check the following connector: C-44

NG→Repair

MUT-II Data List
D

No.01 Vehicle speed sensor<FR>

D

No.02 Vehicle speed sensor<FL>

D

No.03 Vehicle speed sensor<RR>

D

No.04 Vehicle speed sensor<RL>

OK: The speed meter display and MUT-II display match.

NG→Replace the 4WD-ECU.

OK→Intermittent malfunction (Refer to GROUP 00 - Points to

Note for Intermittent Malfunctions)

Check the wheel speed sensor output voltage. (Refer to

P.22A-44.)

 

 

 

 

 

 

 

Content   ..  245  246  247  248   ..