Jeep XJ. Manual - part 539

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  537  538  539  540   ..

 

 

Jeep XJ. Manual - part 539

 

 

TEST

ACTION

APPLICABILITY

4

Warning: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
Disconnect the Airbag Control Module connector
NOTE: Check connectors - Clean and repair as necessary.
Measure the resistance of the Fused Ignition Switch Output Run - Start circuit at the
Airbag Control Module connector.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Fused Ignition Switch Output Run - Start circuit short
to ground.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding. Replace Airbag Run - Start
Fuse.
Perform AIRBAG VERIFICATION TEST - VER 1.

5

WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Turn Ignition On, then reconnect the Battery.
Measure the voltage of the Fused Ignition Switch Output Run - Start Circuit from the
Airbag Control Module connector to ground.
Is the voltage above 4.5 volts?

All

Yes

Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

Repair open Fused Ignition Switch Output Run - Start circuit.
Perform AIRBAG VERIFICATION TEST - VER 1.

36

AIRBAG

LOSS OF IGNITION RUN-START - ACTIVE —

Continued

Symptom:

NO CCD COMMUNICATION - STORED

When Monitored and Set Condition:

NO CCD COMMUNICATION - STORED

When Monitored:

The ACM monitors the CCD Bus for ACM transmitted messages

continuously with the ignition on.

Set Condition:

The code will set if ACM transmitted messages are not detected on the

CCD BUS for 5 consecutive seconds.

POSSIBLE CAUSES

NO CCD BUS DTCS

INTERMITTENT CCD BUS TEST

TEST

ACTION

APPLICABILITY

1

Turn ignition on.
NOTE: Ensure the battery is fully charged.
Active codes must be resolved before diagnosing stored codes.
Read both active and stored codes, and record them.
With the DRBIII

t monitor stored codes as you work through the system.

NOTE: Check for partially seated connectors and spread terminals - Clean
and repair as necessary.
Wiggle the wiring harness of each module on the CCD Bus.
While monitoring the DRB, road test the vehicle.
Is there a wiring, connector problem, or NO CCD COMMUNICATION DTC?

All

Yes

Repair the CCD Bus wiring, connectors or terminals as necessary.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

No problem found at this time. Erase all codes before returning
vehicle to customer.
Perform AIRBAG VERIFICATION TEST - VER 1.

37

AIRBAG

Symptom:

NO CLUSTER MESSAGE - ACTIVE

POSSIBLE CAUSES

MIC, NO CLUSTER MESSAGE - ACTIVE

TEST

ACTION

APPLICABILITY

1

Note: Ensure communications with the Mechanical Instrument Cluster.
With the DRB select PASSIVE RESTRAINTS, AIRBAG and MONITOR DISPLAY,
WARNING LAMP STATUS.
Using the DRB, read the MIC LAMP STATUS monitor.
Cycle the ignition key and observe the warning lamp monitors.
Does the DRBIII

t show MIC LAMP STATUS: ON or OFF?

All

YES

Test Complete.

NO

Replace Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.

38

AIRBAG

Symptom:

PASSENGER SQUIB CIRCUIT OPEN - ACTIVE

When Monitored and Set Condition:

PASSENGER SQUIB CIRCUIT OPEN - ACTIVE

When Monitored:

When the ignition is On, the ACM monitors the resistance of the

Passenger Squib circuits.

Set Condition:

The ACM has detected an open circuit or high resistance on the Passenger

Squib circuits.

POSSIBLE CAUSES

PASSENGER AIRBAG OPEN

PASSENGER AIRBAG LINE 1 CIRCUIT OPEN

PASSENGER AIRBAG LINE 2 CIRCUIT OPEN

ACM, PASSENGER AIRBAG OPEN

TEST

ACTION

APPLICABILITY

1

Note: Ensure the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
CAUTION: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Passenger Airbag Module.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 brown cable and jumper harness to the
Passenger Airbag Module connector.
Turn Ignition On, then reconnect the Battery.
With the DRBIII

t, read the active Airbag DTCs.

Does the DRB show PASSENGER SQUIB OPEN?

All

Yes

Go To

2

No

Replace Passenger Airbag.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.

39

AIRBAG

 

 

 

 

 

 

 

Content   ..  537  538  539  540   ..