Jeep Wrangler TJ. Manual - part 111

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  109  110  111  112   ..

 

 

Jeep Wrangler TJ. Manual - part 111

 

 

Symptom:

P0462-FUEL LEVEL SENSOR NO.1 LOW

When Monitored and Set Condition:

P0462-FUEL LEVEL SENSOR NO.1 LOW

When Monitored:

Ignition on and battery voltage above 10.4 volts.

Set Condition:

The fuel level sensor signal voltage goes below 0.0196 of a volt for more

than 90 seconds.

POSSIBLE CAUSES

FUEL LEVEL SENSOR VOLTAGE BELOW 0.0196 OF A VOLT

FUEL LEVEL SENSOR

(N4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO GROUND

(N4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t, read DTCs and record the related Freeze Frame data.

With the DRBIII

t, read the Fuel Level Sensor voltage.

Is the Fuel Level Sensor voltage below 0.0196 of a volt?

All

Yes

→ Go To 2

No

→ Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2

Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Ignition on, engine not running.
With the DRBIII

t, read the Fuel Level Sensor voltage.

Did the Fuel Level Sensor voltage change from below 0.4 of a volt to above 4.0 volts?

All

Yes

→ Replace the Fuel Level Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 3

3

Turn the ignition off.
Disconnect the C2 and C3 PCM harness connectors.
Measure the resistance between ground and the (N4) Fuel Level Signal circuit at the
Fuel Level Sensor harness connector.
Is the resistance below 100 ohms?

All

Yes

→ Repair the short to ground in the (N4) Fuel Level Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 4

169

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

4

Measure the resistance between the (N4) Fuel Level Signal circuit and the (K900)
Sensor ground circuit at the Fuel Pump Module harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the short between the (K900) Sensor ground and the (N4)

Fuel Level Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 5

5

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

170

DRIVEABILITY - NGC

P0462-FUEL LEVEL SENSOR NO.1 LOW —

Continued

Symptom:

P0463-FUEL LEVEL SENSOR NO.1 HIGH

When Monitored and Set Condition:

P0463-FUEL LEVEL SENSOR NO.1 HIGH

When Monitored:

Ignition on and battery voltage above 10.4 volts.

Set Condition:

The fuel level sensor signal voltage at the PCM goes above 4.9 volts for

more than 90 seconds.

POSSIBLE CAUSES

FUEL LEVEL SENSOR VOLTAGE ABOVE 4.9 VOLTS

FUEL LEVEL SENSOR

(N4) FUEL LEVEL SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

(N4) FUEL LEVEL SIGNAL CIRCUIT OPEN

(K900) SENSOR GROUND CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t, read the Fuel Level Sensor voltage.

Is the Fuel Level Sensor voltage above 4.9 volts?

All

Yes

→ Go To 2

No

→ Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

2

Turn the ignition off.
Disconnect the Fuel Pump Module electrical harness connector.
Connect a jumper wire between the (N4) Fuel Level Signal circuit and the (K900)
Sensor ground circuit at the Fuel Pump Module harness connector.
Ignition on, engine not running.
With the DRBIII

t, read the Fuel Level Sensor voltage.

Did the Fuel Level Sensor voltage change from above 4.8 volts to below 0.4 of a volt?

All

Yes

→ Replace the Fuel Level Sensor.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 3

NOTE: Remove the jumper wire before continuing.

171

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the C2 and C3 PCM harness connectors.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Measure the voltage on the (N4) Fuel Level Signal circuit at the Fuel Pump Module
harness connector.
Is the voltage above 5.3 volts?

All

Yes

→ Repair the short to voltage in the (N4) Fuel Level Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 4

4

Turn the ignition off.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (N4) Fuel Level Signal circuit from the Fuel Pump
Module harness connector to the appropriate terminal in special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair the open in the (N4) Fuel Level Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

5

CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K900) Sensor ground circuit from the Fuel Pump
Module harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 6

No

→ Repair the open in the (K900) Sensor ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

6

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

172

DRIVEABILITY - NGC

P0463-FUEL LEVEL SENSOR NO.1 HIGH —

Continued

 

 

 

 

 

 

 

Content   ..  109  110  111  112   ..